PANORAMIC VIEW MONITOR SYSTEM HOW TO PROCEED WITH TROUBLESHOOTING

CAUTION / NOTICE / HINT

PROCEDURE

1. Click here

   VEHICLE BROUGHT TO WORKSHOP

   Result
   Proceed to NEXT

   
   
   • NEXTClick here
2. Click here

   CUSTOMER PROBLEM ANALYSIS

   
   

   1. Ask the customer about the problems and the conditions at the time the malfunction occurred to make sure the problem symptom was not temporarily caused by radio waves in the surrounding environment.

      Tip:

      The parking assist monitor display may be temporarily distorted due to radio waves around the vehicle.

      Problem Symptom	Cause
      The problem symptom indicates a parking assist monitor display malfunction and the problem symptom cannot be reproduced.	The display may be temporarily distorted when the vehicle is close to an object that transmits radio waves, such as a telecommunication tower, an airport or a truck equipped with a transceiver.

      Result
      Proceed to NEXT

   
   
   • NEXTClick here
3. Click here

   INSPECT AUXILIARY BATTERY VOLTAGE

   
   

   1. Measure the auxiliary battery voltage with the power switch off.

      Standard voltage
      11 to 14 V

      If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding.

      Result
      Proceed to NEXT

   
   
   • NEXTClick here
4. Click here

   SYSTEM CHECK

   
   

   1. Check the vehicle specification.

      Result
      Result Proceed to w/ Navigation System A w/ Audio and Visual System B

   
   
   • AClick here
   • BClick here
5. Click here

   CHECK NAVIGATION SYSTEM

   
   

   1. Refer to the navigation system.

      Click here

      Result
      Result Proceed to Navigation system is normal A Navigation system is abnormal B

   
   
   • AClick here

     GO TO STEP 7

   • B

     GO TO NAVIGATION SYSTEMClick here

6. Click here

   CHECK AUDIO AND VISUAL SYSTEM

   
   

   1. Refer to the audio and visual system.

      Click here

      OK
      Audio and visual system is normal.

      Result
      Proceed to OK NG

   
   
   • OKClick here
   • NG

     GO TO AUDIO AND VISUAL SYSTEMClick here

7. Click here

   CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

   
   

   1. Use the GTS to check if the CAN communication system is functioning normally.

      Click here

      Result
      Result Proceed to CAN DTCs are not output A CAN DTCs are output B

   
   
   • AClick here
   • B

     GO TO CAN COMMUNICATION SYSTEMClick here

8. Click here

   CHECK FOR DTC*

   
   

   1. Check for DTCs and note any codes that are output.

      Click here

      
      
      1. Chassis > Panoramic View Monitor > Trouble Codes
      2. 
         
      3. 
         

   2. Clear the DTCs.

      Click here

      
      
      1. Chassis > Panoramic View Monitor > Clear DTCs
      2. 
         
      3. 
         

   3. Recheck for DTCs. Try to prompt the DTC by simulating the original activity that the DTC suggests.

      
      
      1. Chassis > Panoramic View Monitor > Trouble Codes
      2. 
         
      3. 
         

      Result
      Result Proceed to DTC is not output A DTC is output B

   
   
   • AClick here
   • B

     GO TO DIAGNOSTIC TROUBLE CODE CHARTClick here

9. Click here

   PROBLEM SYMPTOMS TABLE

   
   

   1. Refer to the Problem Symptoms Table.

      Click here

      Result
      Result Proceed to Fault is not listed in Problem Symptoms Table A Fault is listed in Problem Symptoms Table B

   
   
   • AClick here
   • BClick here

     GO TO STEP 11

10. Click here

    OVERALL ANALYSIS AND TROUBLESHOOTING*

    
    

    1. Data List / Active Test

       Click here

    2. Terminals of ECU

       Click here

       Result
       Proceed to NEXT

    
    
    • NEXTClick here
11. Click here

    ADJUST, REPAIR OR REPLACE

    Result
    Proceed to NEXT

    
    
    • NEXTClick here
12. Click here

    CONFIRMATION TEST

    Result
    Proceed to NEXT

    
    
    • NEXT

      END