TELEMATICS SYSTEM(for G-BOOK) Transmitted Voice Signal Circuit

WIRING DIAGRAM

B004VKLE01

CAUTION / NOTICE / HINT

Note


  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for G-BOOK.

    Click here

  • When replacing the telematics transceiver, make sure to replace it with a new one.

  • When replacing the radio receiver assembly, always replace it with a new one.

    If a radio receiver assembly which was installed to another vehicle is used, the following may occur:


    • A communication malfunction DTC may be stored.

    • The radio receiver assembly may not operate normally.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - ANTENNA CORD SUB-ASSEMBLY [I/P])


    1. Disconnect the G53 radio receiver assembly connector.

    2. Disconnect the G152 Antenna cord sub-assembly (I/P) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G53-13 (VOR+) - G152-8 (VOR+) Always Below 1 Ω
      G53-14 (VOR-) - G152-7 (VOR-) Always Below 1 Ω
      G53-15 (VOT+) - G152-4 (VOT+) Always Below 1 Ω
      G53-16 (VOT-) - G152-6 (VOT-) Always Below 1 Ω
      G53-13 (VOR+) - Body ground Always 10 kΩ or higher
      G53-14 (VOR-) - Body ground Always 10 kΩ or higher
      G53-15 (VOT+) - Body ground Always 10 kΩ or higher
      G53-16 (VOT-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. CHECK ANTENNA CORD SUB-ASSEMBLY (I/P)


    1. B004XUJC03
      *a

      Front view of wire harness connector

      (to Telematics Transceiver)
      *b

      Front view of wire harness connector

      (to Wire Harness)

      Disconnect the antenna connector from the telematics transceiver.

    2. Disconnect the antenna connector from the wire harness.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-9 (VOR+) - G152-4 (VOT+) Always Below 1 Ω
      A-8 (VOR-) - G152-6 (VOT-) Always Below 1 Ω
      A-4 (VOT+) - G152-8 (VOR+) Always Below 1 Ω
      A-7 (VOT-) - G152-7 (VOR-) Always Below 1 Ω
      A-9 (VOR+) - Body ground Always 10 kΩ or higher
      A-8 (VOR-) - Body ground Always 10 kΩ or higher
      A-4 (VOT+) - Body ground Always 10 kΩ or higher
      A-7 (VOT-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE ANTENNA CORD SUB-ASSEMBLY (I/P) Click here

    OK

  3. CHECK RADIO RECEIVER ASSEMBLY


    1. Remove the radio receiver assembly with the connectors still connected.

    2. B004RDRC02
      *a

      Component with harness connected

      (Radio Receiver Assembly)

      Check for pulses according to the value(s) in the table below.

      Standard
      Tester Connection Condition Specified Condition
      G53-15 (VOT+) - Body ground Calling while using the operator service A waveform synchronized with the sent voice is output
      G53-16 (VOT-) - Body ground Calling while using the operator service A waveform synchronized with the sent voice is output
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE TELEMATICS TRANSCEIVER Click here

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here