Click here

AUDIO AND VISUAL SYSTEM Display does not Dim when Light Control Switch is Turned ON

Click here
Click here
DTC Code DTC Name
  Display does not Dim when Light Control Switch is Turned ON
Click here

DESCRIPTION

If the audio and visual system is turned on with the light control switch in the tail or head position, before AVC-LAN communication is established, the multi-display dims according to the illumination signal received via a direct line.

After AVC-LAN communication is established, the multi-display dims the display according to a dimmer signal sent via AVC-LAN communication.

The radio receiver assembly changes the multi-display between daytime mode and night mode according to the illumination signal input.

Table 1. *a from PANEL P Relay *b Multi-display *c Radio Receiver Assembly *d AVC-LAN Communication Line
Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

Inspect the fuse for circuits related to this system before performing the following procedure.

Tip:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click here

Click here

PROCEDURE


  1. Click here

    CHECK SYMPTOMS


    1. Check the symptoms that occur by viewing the display.

      Result
      Result Proceed to
      There is a delay in when the multi-display dims after the audio and visual system is turned on with the light control switch in the tail or head position. A
      The multi-display dims for a moment and then becomes bright after the audio and visual system is turned on with the light control switch in the tail or head position. B
      When the light control switch is in the tail or head position, the multi-display dims but does not change to night mode.
      When the light control switch is in the tail or head position, the multi-display neither dims nor switches to night mode. C
      Tip:

      • When the audio and visual system is activated with the light control switch in the tail or head position, before AVC-LAN communication is established, the multi-display dims the display according to the illumination signal received via a direct line.

      • After AVC-LAN communication is established, the multi-display dims the display according to a dimmer signal sent via a direct line.

      • The radio receiver assembly changes the multi-display between daytime mode and night mode according to the illumination signal input.


  2. Click here

    CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL CIRCUIT)


    1. Disconnect the G51 multi-display connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G51-13 (GND1) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      G51-2 (ILL) - Body ground

      Power switch on (IG)

      Light control switch in tail or head position

      		 11 to 14 V
      Result
      Proceed to
      OK
      NG

    • OK

      PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLEClick here

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  3. Click here

    CHECK IMAGE QUALITY SETTING


    1. Turn the light control switch to the tail or head position.

    2. Check that daytime mode on the display adjustment screen is set to on.

      Result
      Result Proceed to
      Daytime mode is set to on. A
      Daytime mode is set to off. B

  4. Click here

    CHECK VEHICLE SIGNAL (OPERATION CHECK)


    1. B004SS1

      Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal in Operation Check.

      Click here

    2. Check that the display for "TAIL" changes between ON and OFF according to the light control switch operation.

      OK
      Light Control Switch Display
      Tail or head ON
      Off or AUTO OFF
      Tip:

      • This display is updated once per second. As a result, it is normal for the display to lag behind the actual switch operation.

      • Make sure to move the vehicle to a bright area before performing an operation check with the light control switch in the AUTO position.

      Result
      Proceed to
      OK
      NG

  5. Click here

    CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL CIRCUIT)


    1. Disconnect the radio receiver assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G52-1 (GND1) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      G54-15 (ILL+) - Body ground

      Power switch on (IG)

      Light control switch in tail or head position

      		 11 to 14 V
      Result
      Proceed to
      OK
      NG

    • OK

      PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLEClick here

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR