READ DATA LIST
Tech Tips
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the power switch off.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Tilt & Telescopic / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | Driving distance | Min.: 0 Max.: 999999 |
- | - |
| Total Distance Traveled - Unit | Driving distance unit | km or mile | - | - |
| Tilt Up Limit | Uppermost tilt position | Not Mem or Mem | Not Mem: Position not memorized Mem: Position memorized |
- |
| Tilt Down Limit | Lowermost tilt position | Not Mem or Mem | Not Mem: Position not memorized Mem: Position memorized |
- |
| Telescopic Short Limit | Shortest telescopic position | Not Mem or Mem | Not Mem: Position not memorized Mem: Position memorized |
- |
| Telescopic Long Limit | Longest telescopic position | Not Mem or Mem | Not Mem: Position not memorized Mem: Position memorized |
- |
| Tilt&Telescopic Memory 1 | Tilt and telescopic memory position 1 | Not Mem or Mem | Not Mem: Position not memorized Mem: Position memorized |
- |
| Tilt&Telescopic Memory 2 | Tilt and telescopic memory position 2 | Not Mem or Mem | Not Mem: Position not memorized Mem: Position memorized |
- |
| Tilt&Telescopic Memory 3 | Tilt and telescopic memory position 3 | Not Mem or Mem | Not Mem: Position not memorized Mem: Position memorized |
- |
| Driver Information Memory 1 | Driver Information Memory 1 | Not Mem or Mem | Not Mem: Position not memorized Mem: Position memorized |
- |
| Driver Information Memory 2 | Driver Information Memory 2 | Not Mem or Mem | Not Mem: Position not memorized Mem: Position memorized |
- |
| Driver Information Memory 3 | Driver Information Memory 3 | Not Mem or Mem | Not Mem: Position not memorized Mem: Position memorized |
- |
| Ignition Switch (CAN) | Communication state of power switch | ON or OFF | ON: Communication normal OFF: Communication interrupted |
- |
| Handle Position | Steering wheel position signal | Away or Return | Away: Steering wheel in away position Return: Steering wheel in return position |
- |
| Ignition Switch | Input state of power switch | ON or OFF | ON: Input signal normal OFF: Input signal interrupted |
- |
| Tilt Manual Switch Up | Input state of tilt up switch | ON or OFF | - | - |
| Tilt Manual Switch Down | Input state of tilt down switch | ON or OFF | - | - |
| Telescopic Manual Switch Short | Input state of telescopic contract switch | ON or OFF | - | - |
| Telescopic Manual Switch Long | Input state of telescopic extend switch | ON or OFF | - | - |
| Tilt&Telescopic Manual Switch Voltage | Voltage data of tilt and telescopic switch | Min.: 0.00 V Max.: 4.99 V |
Neutral position: Below 0.20 V Tilt up: 1.67 to 2.13 V Tilt down: 0.54 to 0.74 V Telescopic contract: 1.08 to 1.40 V Telescopic extend: 2.22 to 2.77 V |
- |
| ECU Power Source Voltage | Voltage data of power supply | Min.: 0.00 V Max.: 19.99 V |
11.00 to 14.00 V | - |
| Tilt Position | Current tilt position data | Min.: 0 Max.: 65535 |
28627 to 36864 | - |
| Telescopic Position | Current telescopic position data | Min.: 0 Max.: 65535 |
28627 to 36864 | - |
| Tilt Return Memory Position | Memorized tilt return position data | Min.: 0 Max.: 65535 |
28627 to 36864 | - |
| Telescopic Return Memory Position | Memorized telescopic return position data | Min.: 0 Max.: 65535 |
28627 to 36864 | - |
| Tilt Up Limit Position | Uppermost tilt position data | Min.: 0 Max.: 65535 |
28627 to 36864 | - |
| Tilt Down Limit Position | Lowermost tilt position data | Min.: 0 Max.: 65535 |
28627 to 36864 | - |
| Telescopic Short Limit Position | Shortest telescopic position data | Min.: 0 Max.: 65535 |
28627 to 36864 | - |
| Telescopic Long Limit Position | Longest telescopic position data | Min.: 0 Max.: 65535 |
28627 to 36864 | - |
| Tilt Memory Position 1 | Tilt data of memory position 1 | Min.: 0 Max.: 65535 |
28627 to 36864 | - |
| Telescopic Memory Position 1 | Telescopic data of memory position 1 | Min.: 0 Max.: 65535 |
28627 to 36864 | - |
| Tilt Memory Position 2 | Tilt data of memory position 2 | Min.: 0 Max.: 65535 |
28627 to 36864 | - |
| Telescopic Memory Position 2 | Telescopic data of memory position 2 | Min.: 0 Max.: 65535 |
28627 to 36864 | - |
| Tilt Memory Position 3 | Tilt data of memory position 3 | Min.: 0 Max.: 65535 |
28627 to 36864 | - |
| Telescopic Memory Position 3 | Telescopic data of memory position 3 | Min.: 0 Max.: 65535 |
28627 to 36864 | - |
| Vehicle Speed | Vehicle speed data | Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph) |
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations |
- |
| Driver Tilt Memory Position 1 | Driver tilt memory position 1 | Min.: 0 Max.: 65535 |
28627 to 36864 | - |
| Driver Telescopic Memory Position 1 | Driver telescopic memory position 1 | Min.: 0 Max.: 65535 |
28627 to 36864 | - |
| Driver Tilt Memory Position 2 | Driver tilt memory position 2 | Min.: 0 Max.: 65535 |
28627 to 36864 | - |
| Driver Telescopic Memory Position 2 | Driver telescopic memory position 2 | Min.: 0 Max.: 65535 |
28627 to 36864 | - |
| Driver Tilt Memory Position 3 | Driver tilt memory position 3 | Min.: 0 Max.: 65535 |
28627 to 36864 | - |
| Driver Telescopic Memory Position 3 | Driver telescopic memory position 3 | Min.: 0 Max.: 65535 |
28627 to 36864 | - |
| Tilt Motor Machine Lock Memory Data | Tilt Motor Machine Lock Memory Data | Data or Not Data | - | - |
| Telescopic Motor Machine Lock Memory Data | Telescopic Motor Machine Lock Memory Data | Data or Not Data | - | - |
| Autoaway/Return Operation Setting | Autoaway/Return Operation Setting | Tilt ON, Telescopic ON, Tilt&Telescopic ON or Tilt&Telescopic OFF | Tilt ON: Only tilt operations permitted Telescopic ON: Only telescopic operations permitted Tilt&Telescopic ON: Tilt and telescopic operations permitted Tilt&Telescopic OFF: Tilt and telescopic operations prohibited |
- |
ACTIVE TEST
Tech Tips
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Turn the power switch off.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Tilt & Telescopic / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range |
|---|---|---|
| Tilt Motor | Tilt operation | UP/DOWN |
| Telescopic Motor | Telescopic operation | LONG/SHORT |