PARKING BRAKE ASSEMBLY REASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. APPLY HIGH TEMPERATURE GREASE


    1. B004TCQC02
      B004VGX High Temperature Grease

      Apply high temperature grease to the areas of the parking brake plate which make contact with the shoe as shown in the illustration.

  2. INSTALL PARKING BRAKE ANCHOR BLOCK SUB-ASSEMBLY


    1. Install the parking brake anchor block sub-assembly and cable support bracket with the 2 nuts.

      Torque:
      75.5 N*m  { 770 kgf*cm, 56 ft.*lbf }

    2. Install the rear axle hub and bearing assembly.

      Click here

  3. CONNECT PARKING BRAKE CABLE


    1. Connect the parking brake actuator assembly with bracket with the nut.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  4. INSTALL PARKING BRAKE SHOE LEVER SUB-ASSEMBLY LH


    1. B004SPR

      Connect the parking brake cable to the parking brake shoe lever sub-assembly LH.

    2. B004Y52C02
      *A for LH Side
      *B for RH Side
      *1 Parking Brake Anchor Block Sub-assembly
      *a Pin
      B004UK4 High Temperature Grease

      Apply high temperature grease to the areas of the parking brake anchor block sub-assembly which make contact with the parking brake shoe lever sub-assembly LH.

      Note

      Check that the parking brake shoe lever sub-assembly is installed so that the pin is positioned as shown in the illustration.

    3. B004YRNC02
      *1 Parking Brake Shoe Lever Sub-assembly LH
      *a Parking Brake Inner Cable
      B004SZX Top of Vehicle

      Check that the parking brake inner cable and parking brake shoe lever sub-assembly LH are securely connected by trying to pull them apart.

  5. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH


    1. B004XH6N02

      Using SST, install the No. 1 parking brake shoe assembly LH with the parking brake shoe hold down spring cup, parking brake shoe hold down compression spring and parking brake shoe hold down spring pin.

      SST
      09718-00011

  6. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH


    1. B004VZVN02

      Using SST, install the No. 2 parking brake shoe assembly LH with the parking brake shoe hold down spring cup, parking brake shoe hold down compression spring and parking brake shoe hold down spring pin.

      SST
      09718-00011

  7. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET


    1. B004V3UC01
      B004VGX High Temperature Grease

      Apply high temperature grease to the parking brake shoe adjusting screw set as shown in the illustration.

    2. B004V95

      Install the parking brake shoe adjusting screw set to the No. 1 parking brake shoe assembly LH and No. 2 parking brake shoe assembly LH.

      Note

      Because the left and right parking brake shoe adjusting screw set are not interchangeable, verify the part number when installing the parking brake shoe adjusting screw set.

  8. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Front Side)


    1. B004S8UN02

      Using SST, install the parking brake shoe return tension spring.

      SST
      09703-30011

  9. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Rear Side)


    1. B004R4TN02

      Using SST, install the parking brake shoe return tension spring.

      SST
      09703-30011

  10. CHECK PARKING BRAKE INSTALLATION


    1. Check that each part is installed properly.

      B004Y6YC02
      *A for LH Side *B for RH Side
      B004SZX Front of the Vehicle - -

      Note

      There should be no oil or grease on the friction surfaces of the shoe linings or discs.

  11. INSTALL REAR DISC LH

    Click here

  12. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

    Click here

  13. CONNECT REAR DISC BRAKE CYLINDER ASSEMBLY LH

    Click here

  14. ADJUST PARKING BRAKE

    Click here

  15. INSTALL REAR WHEEL

    Click here

  16. CHECK PARKING BRAKE CABLE INSTALLATION


    1. B004YASC02
      *a Drive Shaft
      *b Shaft Boot
      *c Parking Brake Cable

      With the vehicle on the ground, check that the gap between the parking brake cable and drive shaft, and the gap between the parking brake cable and shaft boot are 10 mm (0.394 in.) or more.

      Tech Tips

      Make sure that the cable is not twisted.

  17. PERFORM PARKING BRAKE SHOE BEDDING

    Click here