ROOF HEADLINING REASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL NO. 1 ROOF WIRE


    1. Apply butyl tape to the roof headlining ensuring it does not go over the marking.

      Tech Tips


      • Apply securely so that the butyl tape will not shift or peel off.

      • The double portion of the butyl tape is set as a surplus absorbing area.

      B004SQDC02
      *A for 24 Speakers - -
      *a Butyl Tape *b Marking

    2. for LHD:


      1. Attach the No. 1 roof wire to the butyl tape in the order and direction indicated by the arrows shown in the illustration and secure the No. 1 roof wire with pieces of tape.

        Tech Tips


        • Align the positioning tape of the No. 1 roof wire with the protrusion of the roof headlining and wrap tape around them as shown in the part of the illustration labeled A.

        • Make sure that the No. 1 roof wire is securely attached to the roof headlining along its entire length and not twisted.

      2. Attach each guide and each clamp.

        B004SE1C01
        *A w/o Pre-collision *B w/ Pre-collision
        *C for Mono Camera Type *D for Stereo Camera Type
        *E for 24 Speakers *F for 12 Speakers
        *a Align positioning tape of No. 1 roof wire and protrusion of roof headlining - -
        B004VGX Tape B004UCN Positioning Tape

    3. for RHD:


      1. Attach the No. 1 roof wire to the butyl tape in the order and direction indicated by the arrows shown in the illustration and secure the No. 1 roof wire with pieces of tape.

        Tech Tips


        • Align the positioning tape of the No. 1 roof wire with the protrusion of the roof headlining and wrap tape around them as shown in the part of the illustration labeled A.

        • Make sure that the No. 1 roof wire is securely attached to the roof headlining along its entire length and not twisted.

      2. Attach each guide and each clamp.

        B004XO0C01
        *A w/o Pre-collision *B w/ Pre-collision
        *C for Mono Camera Type *D for Stereo Camera Type
        *E for 24 Speakers *F for 12 Speakers
        *a Align positioning tape of No. 1 roof wire and protrusion of roof headlining - -
        B004VGX Tape B004UCN Positioning Tape
    4. B004XFHC01
      B004RMI Install in this Direction

      Turn the visor connectors approximately 90° clockwise and install them to the roof headlining.

  2. INSTALL ROOF SIDE REGISTER BEZEL LH (w/ Rear Cooler)


    1. B004VEH

      Insert the guide and attach the claw to install the roof side register bezel LH.

  3. INSTALL ROOF SIDE REGISTER BEZEL RH (w/ Rear Cooler)

    Tech Tips

    Use the same procedure described for the LH side.

  4. INSTALL REAR SPEAKER GRILLE (for 24 Speakers)


    1. B004TYG

      Align the guide and attach the claw to install the rear speaker grille.

      Tech Tips

      Use the same procedure for the opposite side.

  5. INSTALL ROOF SPEAKER ASSEMBLY (for 24 Speakers, Rear Side)

    Click here

  6. INSTALL ROOF SPEAKER GRILLE LH


    1. for 24 Speakers:


      1. B004VDB

        Insert the guide and attach the claw to install the roof speaker grille LH.

    2. for 12 Speakers:


      1. B004Y7L

        Attach the claw and install the roof speaker grille LH.

  7. INSTALL ROOF SPEAKER GRILLE RH

    Tech Tips

    Use the same procedure described for the LH side.

  8. INSTALL ACTIVE NOISE CONTROL MICROPHONE

    Click here

  9. INSTALL TELEPHONE MICROPHONE ASSEMBLY

    Click here

  10. INSTALL ROOF SPEAKER ASSEMBLY (for 24 Speakers, Rear Side)

    Click here