Click here

REAR DOOR SUNSHADE SYSTEM DATA LIST / ACTIVE TEST

Click here
Click here
Click here

  1. DATA LIST

    Tip:

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Turn the power switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the power switch on (IG).

    4. Turn the GTS on.

    5. Enter the following menus: Body Electrical / Rear Left Door or Rear Right Door / Data List.

    6. According to the display on the GTS, read the Data List.


      • *: w/ Side Window Curtain


      1. Body Electrical > Rear Left Door > Data List
        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Rear Door Sunshade Status Rear curtain sub-assembly LH open/closed status OPEN, OPENING, CLOSE, CLOSING or NG

        OPEN: Rear door sunshade open

        OPENING: Rear door sunshade open operation in progress

        CLOSE: Rear door sunshade closed

        CLOSING: Rear door sunshade close operation in progress

        NG: When unconfirmed immediately after a voltage reset (before position correction (initialization) or a hall sensor malfunction)

        		 -
        Rear Door Sunshade Rear curtain sub-assembly LH fail condition FAIL STOP, RECOV or NORMAL

        FAIL STOP: Stopped according to hall sensor malfunction

        RECOV: Close operation in progress after stopping according to hall sensor malfunction

        NORMAL: Normal

        		 -
        Rear Door Sunshade Stop Status IC condition inside rear curtain sub-assembly LH OK or NG

        OK: Hall sensor normal

        NG: Hall sensor malfunction

        		 -
        Rear Door Quarter Window Sunshade Condition Rear side window curtain assembly LH condition* OK or NG

        OK: Hall sensor normal

        NG: Hall sensor malfunction

        		 -
        Rear Left Master SW Shade Function Function to operate the rear curtain sub-assembly LH and rear side window curtain assembly LH* by operating the rear left seat remote switch of the multiplex network master switch assembly. OFF or ON Customized value displayed -







      1. Body Electrical > Rear Right Door > Data List
        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Rear Door Sunshade Status Rear curtain sub-assembly RH open/closed status OPEN, OPENING, CLOSE, CLOSING or NG

        OPEN: Rear door sunshade open

        OPENING: Rear door sunshade open operation in progress

        CLOSE: Rear door sunshade closed

        CLOSING: Rear door sunshade close operation in progress

        NG: When unconfirmed immediately after a voltage reset (before position correction (initialization) or a hall sensor malfunction)

        		 -
        Rear Door Sunshade Rear curtain sub-assembly RH fail condition FAIL STOP, RECOV or NORMAL

        FAIL STOP: Stopped according to hall sensor malfunction

        RECOV: Close operation in progress after stopping according to hall sensor malfunction

        NORMAL: Normal

        		 -
        Rear Door Sunshade Stop Status IC condition inside rear curtain sub-assembly RH OK or NG

        OK: Hall sensor normal

        NG: Hall sensor malfunction

        		 -
        Rear Door Quarter Window Sunshade Condition Rear side window curtain assembly RH condition* OK or NG

        OK: Hall sensor normal

        NG: Hall sensor malfunction

        		 -
        Rear Right Master SW Shade Function Function to operate the rear curtain sub-assembly RH and rear side window curtain assembly RH* by operating the rear right seat remote switch of the multiplex network master switch assembly. OFF or ON Customized value displayed -






  2. ACTIVE TEST

    Tip:

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Turn the power switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the power switch on (IG).

    4. Turn the GTS on.

    5. Enter the following menus: Body Electrical / Rear Left Door or Rear Right Door / Active Test.

    6. According to the display on GTS perform the "Active Test".


      1. Body Electrical > Rear Left Door > Active Test
        Tester Display Measurement Item Control Range Diagnostic Note
        Rear Door Sunshade Up Rear curtain sub-assembly LH close operation Up or Stop w/ Side Window Curtain specification: a rear side window curtain assembly LH close operation is also performed
        Rear Door Sunshade Down Rear curtain sub-assembly LH open operation Down or Stop w/ Side Window Curtain specification: a rear side window curtain assembly LH open operation is also performed




      1. Body Electrical > Rear Right Door > Active Test
        Tester Display Measurement Item Control Range Diagnostic Note
        Rear Door Sunshade Up Rear curtain sub-assembly RH close operation Up or Stop w/ Side Window Curtain specification: a rear side window curtain assembly RH close operation is also performed
        Rear Door Sunshade Down Rear curtain sub-assembly RH open operation Down or Stop w/ Side Window Curtain specification: a rear side window curtain assembly RH open operation is also performed