LKA/LDA SYSTEM(for Mono Camera Type) TERMINALS OF ECU

CHECK FORWARD RECOGNITION CAMERA

1. Disconnect the N5 forward recognition camera connector.

   Note:
   

   • DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

   • Do not apply excessive force to the N5 forward recognition camera connector.

2. Measure the voltage and resistance according to the value(s) in the table below.

   Tip:

   If the result is not as specified, there may be a malfunction on the wire harness side.

   Terminal No. (Symbol)	Wiring Color	Terminal Description	Condition	Specified Condition
   N5-7 (IGB) - Body ground	R - Body ground	Power source	Power switch on (IG)	11 to 14 V
   			Power switch off	Below 1 V
   N5-10 (GND) - Body ground	BR - Body ground	Ground	Always	Below 1 Ω

3. Reconnect the N5 forward recognition camera connector.

4. Measure the waveform according to the value(s) in the table below.

   Terminal No. (Symbol)	Wiring Color	Terminal Description	Condition	Specified Condition
   N5-2 (STRV) - N5-10 (GND)	GR - BR	LIN communication signal	Power switch on (IG)	Pulse generation (See waveform 1)

5. WAVEFORM 1

   
   
   1. 

      LIN communication signal

      Item	Content
      Terminal Name	Between N5-2(STRV) and N5-10 (GND)
      Tester Range	5 V/DIV., 10 msec./DIV.
      Condition	Power switch on (IG)

      Tip:

      Oscilloscope waveform samples are provided here for informational purposes. Noise and fluttering waveforms have been omitted.

6. Check for pulses according to the value(s) in the table below.

   Terminal No. (Symbol)	Wiring Color	Terminal Description	Condition	Specified Condition
   N5-5 (CA1P) - N5-10 (GND)	B - BR	CAN communication signal	Power switch on (IG)	Pulse generation (See waveform 1)
   N5-11 (CA1N) - N5-10 (GND)	BE - BR	CAN communication signal	Power switch on (IG)	Pulse generation (See waveform 2)
   N5-6 (CANH) - N5-10 (GND)	B - BR	CAN communication signal	Power switch on (IG)	Pulse generation (See waveform 1)
   N5-12 (CANL) - N5-10 (GND)	V - BR	CAN communication signal	Power switch on (IG)	Pulse generation (See waveform 2)

7. WAVEFORM 1

   
   
   1. 

      Table 1.

      *a	1 V/DIV.
      *b	10 μsec./DIV.

      CAN communication signal

      Item	Content
      Terminal Name	Between N5-5 (CA1P) and N5-10 (GND) Between N5-6 (CANH) and N5-10 (GND)
      Tester Range	1 V/DIV., 10 μsec./DIV.
      Condition	Power switch on (IG)

      Tip:

      The waveform varies depending on the CAN communication signal.

8. WAVEFORM 2

   
   
   1. 

      Table 2.

      *a	1 V/DIV.
      *b	10 μsec./DIV.

      CAN communication signal

      Item	Content
      Terminal Name	Between N5-11 (CA1N) and N5-10 (GND) Between N5-12 (CANL) and N5-10 (GND)
      Tester Range	1 V/DIV., 10 μsec./DIV.
      Condition	Power switch on (IG)

      Tip:

      The waveform varies depending on the CAN communication signal.

CHECK DRIVING SUPPORT ECU ASSEMBLY

1. Measure the voltage and resistance according to the value(s) in the table below.

   Tip:

   If the result is not as specified, there may be a malfunction on the wire harness side.

   Terminal No. (Symbol)	Wiring Color	Terminal Description	Condition	Specified Condition
   G68-7 (B) - G68-28 (GND)	LA-V - LA	Power source	Power switch on (IG)	11 to 14 V
   			Power switch off	Below 1 V
   G68-23 (SPSW) - G68-28 (GND)	Y - LA	Steering pad switch signal (LKA/LDA main switch signal)	Power switch off LKA/LDA main switch (steering pad switch assembly) off	1 MΩ or higher
   			Power switch off LKA/LDA main switch (steering pad switch assembly) on	228 to 252 Ω
   G68-28 (GND) - Body ground	LA - Body ground	Ground	Always	Below 1 Ω

2. Check for pulses according to the value(s) in the table below.

   Terminal No. (Symbol)	Wiring Color	Terminal Description	Condition	Specified Condition
   G68-8 (CA1P) - G68-28 (GND)	R - LA	CAN communication signal	Power switch on (IG)	Pulse generation (See waveform 1)
   G68-9 (CA1N) - G68-28 (GND)	W - LA	CAN communication signal	Power switch on (IG)	Pulse generation (See waveform 2)
   G68-10 (CA2H) - G68-28 (GND)	R - LA	CAN communication signal	Power switch on (IG)	Pulse generation (See waveform 1)
   G68-11 (CA2L) - G68-28 (GND)	W - LA	CAN communication signal	Power switch on (IG)	Pulse generation (See waveform 2)

3. WAVEFORM 1

   
   
   1. 

      Table 3.

      *a	1 V/DIV.
      *b	10 μsec./DIV.

      CAN communication signal

      Item	Content
      Terminal Name	Between G68-8 (CA1P) - G68-28 (GND) Between G68-10 (CA2H) - G68-28 (GND)
      Tester Range	1 V/DIV., 10 μsec./DIV.
      Condition	Power switch on (IG)

      Tip:

      The waveform varies depending on the CAN communication signal.

4. WAVEFORM 2

   
   
   1. 

      Table 4.

      *a	1 V/DIV.
      *b	10 μsec./DIV.

      CAN communication signal

      Item	Content
      Terminal Name	Between G68-9 (CA1N) - G68-28 (GND) Between G68-11 (CA2L) - G68-28 (GND)
      Tester Range	1 V/DIV., 10 μsec./DIV.
      Condition	Power switch on (IG)

      Tip:

      The waveform varies depending on the CAN communication signal.

CHECK STEERING VIBRATION ECU

1. Measure the voltage and resistance according to the value(s) in the table below.

   Terminal No. (Symbol)	Terminal Description	Condition	Specified Condition
   z7-4 (IG) - z7-1 (GND)	Power source	Power switch on (IG)	11 to 14 V
   		Power switch off	Below 1 V
   A-3 (M+) - z7-1 (GND)	Steering vibration operation signal	Power switch on (IG) Steering vibration operating	Pulse generation
   		Power switch on (IG) Steering vibration not operating	Below 1 V
   z7-1 (GND) - Body ground	Ground	Always	Below 1 Ω

2. Measure the waveform according to the value(s) in the table below.

   Terminal No. (Symbol)	Terminal Description	Condition	Specified Condition
   z7-2 (LIN1) - z7-1 (GND)	LIN communication signal	Power switch on (IG)	Pulse generation