DYNAMIC RADAR CRUISE CONTROL SYSTEM(for Stereo Camera Type) Steering Pad Switch Circuit

DESCRIPTION


WIRING DIAGRAM

B004WWWE09

CAUTION / NOTICE / HINT

Note


  • Before replacing the hybrid vehicle control ECU, refer to Registration.

    Click here

  • The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

    Click here

PROCEDURE


  1. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Radar Cruise 1 / Data List.

    5. Read the Data List according to the display on the GTS.

      Click here


      Powertrain > Radar Cruise1 > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Cancel Switch CANCEL switch status ON or OFF

      ON: CANCEL switch pushed

      OFF: CANCEL switch not pushed

      		 -
      -SET Switch -SET switch status ON or OFF

      ON: -SET switch pushed

      OFF: -SET switch not pushed

      		 -
      +RES Switch +RES switch status ON or OFF

      ON: +RES switch pushed

      OFF: +RES switch not pushed

      		 -
      Cruise Main Switch Operation Condition Cruise control main switch status ON or OFF

      ON: Cruise control main switch pushed

      OFF: Cruise control main switch not pushed

      		 -

      Powertrain > Radar Cruise1 > Data List
      Tester Display
      Cancel Switch
      -SET Switch
      +RES Switch
      Cruise Main Switch Operation Condition
      OK
      The value of each measurement item changes according to the operation of the steering pad switch assembly.
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

  2. INSPECT STEERING PAD SWITCH ASSEMBLY


    1. Remove the steering pad switch assembly.

      Click here

    2. Inspect the steering pad switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE STEERING PAD SWITCH ASSEMBLY Click here

    OK

  3. INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY


    1. Remove the spiral with sensor cable sub-assembly.

      Click here

    2. Inspect the spiral with sensor cable sub-assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU ASSEMBLY AND BODY GROUND)


    1. Disconnect the G27 spiral cable sub-assembly connector.

    2. Disconnect the G93 hybrid vehicle control ECU assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G27-13 (CCS) - G93-9 (CCS) Always Below 1 Ω
      G27-2 (ECC) - Body ground Always Below 1 Ω
      G27-13 (CCS) or G93-9 (CCS) - Body ground Always 10 kΩ or higher

    4. Connect the G93 hybrid vehicle control ECU assembly connector.

    5. Connect the G27 spiral cable sub-assembly connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU ASSEMBLY AND BODY GROUND)