Click here

INTAKE MANIFOLD INSTALLATION

Click here
Click here

PROCEDURE


  1. Click here

    INSTALL STUD BOLT

    Tip:

    If a stud bolt is deformed or the threads are damaged, replace it.


    1. Using an E8 "TORX" socket wrench, install the 2 stud bolts to the intake manifold.

      10 N*m 102 kgf*cm 7 ft.*lbf
  2. Click here

    INSTALL INTAKE MANIFOLD


    1. B004SUIC01
      *a Protrusion

      Set 2 new No. 1 intake manifolds to head gaskets on each cylinder head as shown in the illustration.

      Note:

      • Align the port holes of the gasket, cylinder head sub-assembly and cylinder head LH.

      • Be careful of the installation direction.

    2. Set the intake manifold on the cylinder head sub-assembly and cylinder head LH.

    3. Install and uniformly tighten the 4 bolts and 4 nuts.

      21 N*m 214 kgf*cm 15 ft.*lbf
  3. Click here

    INSTALL EGR VALVE ASSEMBLY

    Click here

  4. Click here

    INSTALL WATER BY-PASS HOSE

    Click here

  5. Click here

    CONNECT NO. 15 WATER BY-PASS HOSE

    Click here

  6. Click here

    CONNECT GENERATOR CABLE AND MOTOR CABLE (for LHD)

    Click here

  7. Click here

    INSTALL FUEL DELIVERY WITH SENSOR PIPE ASSEMBLY

    Click here

  8. Click here

    CONNECT WIRE HARNESS

    Click here

  9. Click here

    INSTALL FUEL TUBE SUB-ASSEMBLY

    Click here

  10. Click here

    INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

    Click here

  11. Click here

    INSTALL INTAKE AIR SURGE TANK ASSEMBLY

    Note:

    Do not apply oil to the bolts and nuts as listed below:

    Oil Application Prohibited Bolt and Nut
    Bolt and Nut for Intake Air Surge Tank Assembly and Intake Manifold
    Bolt for No. 2 Surge Tank Stay and Intake Air Surge Tank Assembly

    1. Install a new air surge tank to intake manifold gasket to the intake air surge tank assembly.

    2. Set the intake air surge tank assembly on the intake manifold.

    3. Install and uniformly tighten the 5 bolts and 2 nuts.

      21 N*m 214 kgf*cm 15 ft.*lbf

    4. Install the No. 2 surge tank stay to the intake air surge tank assembly and camshaft housing sub-assembly LH with the 2 bolts.

      21 N*m 214 kgf*cm 15 ft.*lbf

    5. Connect the PCV hose to the intake air surge tank assembly, and slide the clamp to secure the hose.

    6. Attach the 2 clamps to connect the transmission breather assembly.

    7. for RHD:

      Attach the 2 clamps to connect the motor cable and generator cable.

    8. Attach the clamp to connect the No. 1 fuel tube sub-assembly.

    9. Connect the wire harness with the bolt.

      10 N*m 102 kgf*cm 7 ft.*lbf

    10. Attach the 3 clamps.

    11. Connect the vacuum sensor connector.

    12. Connect the purge VSV to the intake air surge tank assembly with the bolt.

      21 N*m 214 kgf*cm 15 ft.*lbf

    13. Connect the No. 1 fuel vapor feed hose to the intake air surge tank assembly.

    14. Connect the purge VSV connector.

  12. Click here

    INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

    Click here

  13. Click here

    INSPECT FOR FUEL LEAK

    Click here