INVERTER WITH CONVERTER COMPONENTS
ILLUSTRATION
| *1 | NEGATIVE AUXILIARY BATTERY TERMINAL | *2 | LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | - | - |
ILLUSTRATION
| *A | for Power Seat | - | - |
| *1 | NO. 1 ROOM PARTITION COVER | *2 | NO. 8 HV BATTERY SHIELD PANEL |
| *3 | SERVICE PLUG GRIP | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for Fixed Seat Type | - | - |
| *1 | DOOR ARMREST CAP | *2 | NO. 8 HV BATTERY SHIELD PANEL |
| *3 | SERVICE PLUG GRIP | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | LOWER RADIATOR AIR DEFLECTOR | *2 | RADIATOR COVER PLATE |
| *3 | UPPER RADIATOR SUPPORT SEAL | - | - |
ILLUSTRATION
| *A | for LHD | - | - |
| *1 | CONNECTOR COVER ASSEMBLY | *2 | ENGINE ROOM MAIN WIRE (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR) |
| *3 | FENDER APRON BRACE SUB-ASSEMBLY RH | *4 | GENERATOR CABLE |
| *5 | HIGH VOLTAGE FUSE | *6 | HV FLOOR UNDER WIRE |
| *7 | INVERTER COVER ASSEMBLY RH | *8 | INVERTER MOTOR CABLE BRACKET ASSEMBLY |
| *9 | INVERTER TERMINAL COVER | *10 | INVERTER WITH CONVERTER ASSEMBLY |
| *11 | MOTOR CABLE | *12 | NO. 4 INVERTER COOLING HOSE |
| *13 | NO. 5 INVERTER COOLING HOSE | *14 | ENGINE ROOM MAIN WIRE (HV AIR CONDITIONING WIRE) |
| *15 | HOSE CLIP | *16 | WIRING HARNESS CLAMP BRACKET |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| * | For use with SST | ● | Non-reusable part |
ILLUSTRATION
| *A | for LHD | - | - |
| *1 | INVERTER BUS-BAR PLATE SUB-ASSEMBLY | *2 | NO. 1 INVERTER COOLING HOSE |
| *3 | NO. 4 INVERTER BRACKET | *4 | NO. 6 INVERTER BRACKET |
| *5 | HOSE CLIP | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *A | for RHD | - | - |
| *1 | CONNECTOR COVER ASSEMBLY | *2 | ENGINE ROOM MAIN WIRE (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR) |
| *3 | FENDER APRON BRACE SUB-ASSEMBLY LH | *4 | GENERATOR CABLE |
| *5 | HIGH VOLTAGE FUSE | *6 | HV FLOOR UNDER WIRE |
| *7 | INVERTER COVER ASSEMBLY LH | *8 | INVERTER MOTOR CABLE BRACKET ASSEMBLY |
| *9 | INVERTER TERMINAL COVER | *10 | INVERTER WITH CONVERTER ASSEMBLY |
| *11 | MOTOR CABLE | *12 | NO. 4 INVERTER COOLING HOSE |
| *13 | NO. 5 INVERTER COOLING HOSE | *14 | ENGINE ROOM MAIN WIRE (HV AIR CONDITIONING WIRE) |
| *15 | HOSE CLIP | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | - | - |
ILLUSTRATION
| *A | for RHD | - | - |
| *1 | INVERTER BUS-BAR PLATE SUB-ASSEMBLY | *2 | NO. 1 INVERTER COOLING HOSE |
| *3 | NO. 4 INVERTER BRACKET | *4 | NO. 6 INVERTER BRACKET |
| *5 | HOSE CLIP | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |