MOTOR GENERATOR CONTROL SYSTEM, Diagnostic DTC:P0D2D16, P0D2D17, P0D2D1F

DTC Code DTC Name
P0D2D16 Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Above Threshold
P0D2D1F Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Intermittent

DESCRIPTION

The inverter contains a three-phase bridge circuit, which consists of 6 power transistors (IGBTs) each for the generator (MG1) and motor (MG2). The inverter converts high-voltage direct current from the HV battery into three-phase alternating current for the generator (MG1) and motor (MG2); it also converts three-phase alternating current supplied by generator (MG1) and motor (MG2) into direct current for the HV battery. The motor generator control ECU (MG ECU) controls the actuation of the power transistors (IGBTs). The inverter transmits information necessary for control, such as amperage and voltage, to the motor generator control ECU (MG ECU).

B004X5UE01

The motor generator control ECU (MG ECU) uses an inverter voltage sensor, which is built into the inverter, to detect boosted high voltage (VH) and allow control of the voltage boost.

The inverter voltage sensor outputs voltage that fluctuates between 0 to 5 V according to changes in VH.

The motor generator ECU monitors the inverter voltage sensor and detects the following malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0D2D16 Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Below Threshold

Inverter voltage (VH) signal is stuck low:

DTC stored when the VH sensor signal is excessively low.

(1 trip detection logic)

 Inverter with converter assembly Comes on

Master Warning Light:

Comes on
P0D2D17 Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Above Threshold

Inverter voltage (VH) signal is stuck high:

DTC stored when the VH sensor signal is excessively high.

(1 trip detection logic)

 Inverter with converter assembly Comes on

Master Warning Light:

Comes on
P0D2D1F Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Intermittent

An excessively high or low voltage signal is output from the inverter voltage sensor (VH) when DTC P0C7917, P0D3319, P1C5D19 or P1C5F19 is stored.

(1 trip detection logic)

 Inverter with converter assembly Does not come on

Master Warning Light:

Does not come on
Related Data List
DTC No. Data List

P0D2D16

P0D2D17

P0D2D1F

 VH Voltage

CONFIRMATION DRIVING PATTERN

Tech Tips

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click here


  1. Connect the GTS to the DLC3.

  2. Turn the power switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the power switch off and wait for 2 minutes or more.

  5. Turn the power switch on (IG) and turn the GTS on.

  6. Turn the power switch on (READY) and wait for 5 seconds or more.

  7. Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.

  8. Check the DTC judgment result.

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE, perform driving pattern again.

PROCEDURE


  1. REPLACE INVERTER WITH CONVERTER ASSEMBLY

    Click here

    Result
    Proceed to
    NEXT

    NEXT

    COMPLETED