REAR AXLE HUB BOLT REPLACEMENT

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear axle hub bolt removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link

  • Rear disc (Including removal and installation)

  • Parking brake shoe (Including removal and installation)

 Parking brake bedding Electric parking brake system

Click here

Note


  • When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1341, C1342, C1343 and/or C1344 may be stored. As there is no malfunction, clear the DTCs.

  • While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch is turned on. Therefore, when servicing, do not depress the brake pedal or open/close the doors while the auxiliary battery is connected.

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. AIR SUSPENSION CONTOL PROHIBITED (w/ Air Suspension)

    Click here

  2. DISCONNECT BRAKE BOOSTER PUMP CONNECTOR

    Click here

  3. REMOVE REAR WHEEL

    Click here

  4. DISCONNECT REAR DISC BRAKE CYLINDER ASSEMBLY


  5. REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG


  6. REMOVE REAR DISC LH


  7. REMOVE REAR AXLE HUB BOLT


    1. B004SWWC01
      *a Service Nut
      *b Hold
      *c Turn

      Temporarily install 2 service nuts to the rear axle hub bolts as shown in the illustration.

      Recommended Service Nut
      Thread diameter: 14.0 mm (0.551 in.)
      Thread pitch: 1.5 mm (0.0591 in.)

      Note

      Install the service nuts to prevent damage to the rear axle hub bolts.

    2. Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.

      SST
      09650-17011

      Note

      Do not damage the threads of the rear axle hub bolts.

  8. INSTALL REAR AXLE HUB BOLT


    1. B004TI1C01
      *a Service Nut
      *b Washer
      *c Hold
      *d Turn

      Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.

    2. Install a washer and service nut to the rear axle hub bolt as shown in the illustration.

      Recommended Service Nut
      Thread diameter: 14.0 mm (0.551 in.)
      Thread pitch: 1.5 mm (0.0591 in.)

      Tech Tips

      Recommended washer thickness is 5 mm (0.197 in.) or more.

    3. Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.

      Note


      • Install the service nuts to prevent damage to the rear axle hub bolts.

      • Do not damage the threads of the rear axle hub bolts.

    4. Remove the 3 service nuts and washer from the 3 rear axle hub bolts.

  9. INSTALL REAR DISC LH


  10. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG


  11. CONNECT REAR DISC BRAKE CYLINDER ASSEMBLY


  12. ADJUST PARKING BRAKE

    Click here

  13. INSTALL REAR WHEEL

    Click here

  14. CONNECT BRAKE BOOSTER PUMP CONNECTOR

    Click here

  15. PERFORM PARKING BRAKE SHOE BEDDING

    Click here