Click here

PARKING LOCK RELEASE CABLE INSTALLATION

Click here
Click here

CAUTION / NOTICE / HINT

Note:

The parking shift lock release stopper used to prevent improper installation that is included with the parking lock release lever supply part is removed in the No. 2 parking lock release cable assembly installation procedure.

Click here

PROCEDURE


  1. Click here

    INSTALL NO. 2 PARKING RELEASE CABLE BRACKET SUB-ASSEMBLY

    Tip:

    Perform this procedure only when replacing the No. 2 parking release cable bracket sub-assembly.


    1. B004XX5

      Install the No. 2 parking release cable bracket sub-assembly to the engine rear mounting member with the 2 nuts.

      5.0 N*m 51 kgf*cm 44 in.*lbf
  2. Click here

    INSTALL PARKING LOCK RELEASE LEVER ASSEMBLY


    1. B004T54C02
      *A for LHD
      *B for RHD
      B004SZX Bolt A
      B004UK4 Bolt B

      Pass the parking lock release lever assembly through the floor panel through holes and install it with the 4 bolts.

      Tip:

      • Do not damage the cable with the floor panel through holes.

      • Do not bend the cable.

      for bolt A
      12 N*m 122 kgf*cm 9 ft.*lbf
      for bolt B
      14.5 N*m 148 kgf*cm 11 ft.*lbf
    2. B004X23C02
      *a Protector
      *b Clamp

      Install the No. 1 parking lock release cable clamp bracket to the parking lock release lever assembly protector.

      Note:

      Securely install the protector into the clamp.

    3. B004XXXC01
      *a Stopper

      Install the No. 1 parking lock release cable clamp bracket to the body with the nut.

      8.0 N*m 82 kgf*cm 71 in.*lbf
      Note:

      The rear side of the floor stud bolt is used as a stopper. Therefore, install the nut to the front side.

  3. Click here

    INSTALL TRANSMISSION CONTROL SHAFT LEVER


    1. B004US5

      Install the transmission control shaft lever to the No. 2 parking lock release cable assembly with the nut and spring washer.

      12.7 N*m 130 kgf*cm 9 ft.*lbf
  4. Click here

    INSTALL NO. 2 PARKING LOCK RELEASE CABLE ASSEMBLY


    1. B004R8LC01
      *a Long Hole

      Install the No. 2 parking lock release cable assembly to the No. 2 parking release cable bracket sub-assembly with the 2 bolts.

      7.5 N*m 76 kgf*cm 66 in.*lbf
      Note:

      Install so that the long hole is at the bottom side of the vehicle.

    2. B004UGNC01
      *1 Parking Lock Release Lever Assembly Cable End
      *2 No. 2 Parking Lock Release Cable Assembly Cable End

      Connect the parking lock release lever assembly cable end to the No. 2 parking lock release cable assembly cable end.

    3. B004Y4MC01
      *1 Cover
      B004RMI Connect

      Attach the 2 claws and connect the cover to the No. 2 parking lock release cable assembly as shown in the illustration.

    4. B004TQRC01
      B004SZX Bolt
      B004UK4 Nut and Spring Washer

      Connect the No. 2 parking lock release cable assembly to the shift control actuator assembly with the nut, spring washer and 2 bolts.

      for bolt
      8.0 N*m 82 kgf*cm 71 in.*lbf
      for nut
      12.7 N*m 130 kgf*cm 9 ft.*lbf
    5. B004U8HC02
      *A for LHD
      *B for RHD
      B004RMI Remove

      Remove the parking shift lock release stopper used to prevent improper installation from the parking lock release lever assembly.

      Tip:

      The parking shift lock release stopper used to prevent improper installation is only included with supply parts.

  5. Click here

    INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY

    Click here