ACTIVE REAR WING INSTALLATION

PROCEDURE

1. INSTALL COLLAR

   
   

   1. 

      Install the 8 collars.

2. INSTALL ACTIVE REAR WING

   
   

   1. Insert the guides and attach the clip.

      

   2. Install the active rear wing with the 14 nuts.

      Torque:

      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

   3. Connect the connector.

3. INSPECT REAR SPOILER SUB-ASSEMBLY

   
   

   1. Check the difference in level (a) between the luggage compartment door panel and upper surface of the rear spoiler when the rear spoiler is retracted.

      

      Standard
      Area Measurement Area Measurement Front [A-A] 0 to 1.5 mm (0 to 0.059 in.) 0 to -1.5 mm (0 to -0.059 in.) Rear [B-B] 0 to 1.5 mm (0 to 0.059 in.) 0 to -1.5 mm (0 to -0.059 in.)

      Tech Tips

      
      

      • For the (a) dimension, (+) represents the condition that the rear spoiler is above the luggage compartment door panel level. (-) represents the condition that the rear spoiler is below the luggage compartment door panel level.

      • Use the same procedure for the RH and LH sides.

4. ADJUST REAR SPOILER SUB-ASSEMBLY

   Tech Tips

   Use the same procedure is for the other side.

   
   

   1. 

      Using a T30 "TORX" socket wrench, remove the 2 "TORX" screws.

   2. 

      *a	Up
      *b	Down

      Using a screwdriver, turn the 2 collars of the top cover lock control link sub-assembly LH to adjust the height.

   3. Using a T30 "TORX" socket wrench, install 2 new "TORX" screws.

      Torque:

      5.1 N*m  { 52 kgf*cm, 45 in.*lbf }

      Note

      Do not reuse the "TORX" screw that has been removed.

5. INSTALL REAR SPOILER DRAIN END CAP LH

   Tech Tips

   When installing the rear spoiler seal, heat the rear spoiler drain end cap LH and rear spoiler seal.

   Standard
   Item Temperature Rear Spoiler Drain End Cap LH 20 to 30°C (68 to 86°F) Rear Spoiler Seal

   CAUTION:

   
   

   • Do not touch the heat light and heated parts.

   • Touching the heat light may result in burns.

   • Touching heated parts for a long time may result in burns.

   

   *a	Heated Part
   *b	Heat Light

   
   

   1. When reusing the rear spoiler drain end cap LH, remove the double-sided tape remaining on the installation surface of the rear spoiler seal.

   2. Remove the peeling paper of the double-sided tape trying not to touch the adhesional surface.

   3. 

      Install a new rear spoiler seal to the rear spoiler drain end cap LH.

      Tech Tips

      Press the rear spoiler firmly to install it.

   4. Install the rear spoiler drain end cap LH with the 3 nuts.

      Torque:

      6.7 N*m  { 68 kgf*cm, 59 in.*lbf }

6. INSTALL REAR SPOILER DRAIN END CAP RH

   Tech Tips

   Use the same procedure described for the LH side.

7. CONNECT SLIDING ROOF DRAIN HOSE

   
   

   1. 

      Install in this Direction

      Connect the sliding roof hose with the clip.

      Tech Tips

      Use the same procedure for the RH and LH sides.

8. INSTALL LUGGAGE COMPARTMENT DOOR COVER

   Click here

9. INSTALL LUGGAGE COMPARTMENT DOOR ASSIST GRIP

   Click here

10. INITIALIZE ACTIVE REAR WING SYSTEM

    Click here

11. CHECK ACTIVE REAR WING SYSTEM

    Click here