DATA LIST
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Tech Tips
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Turn the power switch off.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical and Chassis / (desired system) / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Wiper Switch HI (Line) | Windshield wiper switch assembly HI signal (abnormal control system) input condition | OFF or ON | OFF: Windshield wiper switch assembly not in HI position ON: Windshield wiper switch assembly in HI position |
- |
| Wiper Stop Position | Displays windshield wiper motor assembly stop position | Store Are, Lower Rev Pos, Wipe Area or Upper Rev Pos | Store Are/Lower Rev Pos: Lower reverse position or lower Lower Rev Pos: Lower reverse position or lower reverse position or less Wipe Area: Between lower reverse position and upper reverse position Upper Rev Pos: Upper reverse position |
- |
| Wiper Position | Displays the wiper position | Store Are, Exchange Position or Wipe Area | Store Area: Lower reverse position Exchange Position: Service position Wipe Area: Lower reverse position higher or upper reverse position or less |
- |
| Status of Motor Lock | Windshield wiper motor assembly stuck malfunction condition | Normal or Lock | Normal: Normal operation possible Lock: Operation unavailable |
- |
| Status of Temperature Protection | Condition of temperature protection control for the windshield wiper motor assembly | Normal, LO Operation, INT Operation or Stop | Normal: Motor temperature less than 95°C (203°F) LO Operation: Motor temperature 95°C (203°F) or more INT Operation: Motor temperature 100°C (212°F) or more Stop: Motor temperature 105°C (221°F) or more |
- |
| Status of Overvoltage | Windshield wiper motor assembly voltage condition | Normal or Overvoltage | Normal: Normal operation possible Overvoltage: Operation unavailable |
- |
| Status of Low Voltage | Windshield wiper motor assembly voltage condition | Normal or Low Voltage | Normal: Normal operation possible Low Voltage: Operation unavailable |
- |
| Motor Shaft Angle | Displays windshield wiper motor assembly rotation angle | 0 to 255 ° | Displays windshield wiper motor assembly rotation angle |
Tech Tips
|
| Motor Temperature | Displays windshield wiper motor assembly internal temperature sensor value | Min.: -128°C (-262°F), Max.: 128°C (262°F) | Displays windshield wiper motor assembly internal temperature sensor value | - |
| Motor Current | Displays windshield wiper motor assembly current | 0 to 63 A | Displays windshield wiper motor assembly current | - |
| Motor Power Supply Voltage | Displays windshield wiper motor assembly voltage | 0 to 63 V | Displays windshield wiper motor assembly voltage | - |
| Wiper Stop Position (Sub Motor) | Displays No. 2 windshield wiper motor assembly stop position | Store Are, Lower Rev Pos, Wipe Area or Upper Rev Pos | Lower Rev Pos: Lower reverse position or lower reverse position or less Wipe Area: Above or below the upper reverse position from the lower reverse position Upper Rev Pos: Upper reverse position or higher |
- |
| Status of Motor Lock (Sub Motor) | No. 2 windshield wiper motor assembly stuck malfunction condition | Normal or Lock | Normal: Normal operation possible Lock: Operation unavailable |
- |
| Status of Temperature Protection (Sub Motor) | Condition of temperature protection control for the No. 2 windshield wiper motor assembly | Normal, LO Operation, INT Operation or Stop | Normal: Motor temperature less than 95°C (203°F) LO Operation: Motor temperature 95°C (203°F) or more INT Operation: Motor temperature 100°C (212°F) or more Stop: Motor temperature 105°C (221°F) or more |
- |
| Status of Overvoltage (Sub Motor) | No. 2 windshield wiper motor assembly voltage condition | Normal or Overvoltage | Normal: Normal operation possible Overvoltage: Operation unavailable |
- |
| Status of Low Voltage (Sub Motor) | No. 2 windshield wiper motor assembly voltage condition | Normal or Low Voltage | Normal: Normal operation possible Low Voltage: Operation unavailable |
- |
| Motor Shaft Angle (Sub Motor) | Displays No. 2 windshield wiper motor assembly rotation angle | 0 to 255 ° | Displays No. 2 windshield wiper motor assembly rotation angle |
Tech Tips
|
| Motor Temperature (Sub Motor) | Displays No. 2 windshield wiper motor assembly internal temperature sensor value | Min.: -128°C (-262°F), Max.: 128°C (262°F) | Displays No. 2 windshield wiper motor assembly internal temperature sensor value | - |
| Motor Current (Sub Motor) | Displays No. 2 windshield wiper motor assembly current | 0 to 63 A | Displays No. 2 windshield wiper motor assembly current | - |
| Motor Power Supply Voltage (Sub Motor) | Displays No. 2 windshield wiper motor assembly voltage | 0 to 63 V | Displays No. 2 windshield wiper motor assembly voltage | - |
| Number of DTCs | Number of trouble codes | 0 to 255 | When system is normal: 0 When a malfunction is detected: More than 0 |
- |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Sensor Info | Rain sensor temperature circuit condition | OK or NG | OK: Rain sensor is normal NG: Malfunction in rain sensor thermistor |
- |
| Sensor Reaction Info | Rain sensor output condition | OK or NG | OK: Rain sensor is normal NG: Malfunction in rain thermistor output |
- |
| Sensor High Temp Info | Rain sensor high temperature condition | OK or NG | OK: Rain sensor is normal NG: Rain sensor high temperature |
- |
| Sensor Low Temp Info | Rain sensor low temperature condition | OK or NG | OK: Rain sensor is normal NG: Rain sensor low temperature |
- |
| Wiper Switch Auto Signal | Windshield wiper switch assembly (AUTO position) condition | OFF or ON | OFF: Windshield wiper switch assembly not in AUTO position ON: Windshield wiper switch assembly in AUTO position |
- |
| Intermittent Time Volume | Intermittent time adjustment volume condition | Shortest, Shorter, Longer or Longest | Shortest: Windshield wiper switch assembly (intermittent time adjustment volume condition) P4 position Shorter: Windshield wiper switch assembly (intermittent time adjustment volume condition) P3 position Longer: Windshield wiper switch assembly (intermittent time adjustment volume condition) P2 position Longest: Windshield wiper switch assembly (intermittent time adjustment volume condition) P1 position |
- |
| Wiper Type | Displays vehicle wiper type | Normal, Reversing (1 Motor) or Reversing (2 Motor) | Shows vehicle wiper type | - |
| Wiper Stop Position | Windshield wiper motor assembly stop position | Store Area, Lower Rev Pos, Wipe Area or Upper Rev Pos | Store Area: Lower reverse position or lower reverse position or less Lower Rev Pos: Above or below the upper reverse position from the lower reverse position Wipe Area: Outside of lower reverse position or upper reverse position, retraction range Upper Rev Pos: Upper reverse position |
- |
| Wiper Stop Position (Sub Motor) | No. 2 Windshield wiper motor assembly stop position | Store Area, Lower Rev Pos, Wipe Area or Upper Rev Pos | Store Area: Lower reverse position or lower reverse position or less Lower Rev Pos: Above or below the upper reverse position from the lower reverse position Wipe Area: Outside of lower reverse position or upper reverse position, retraction range Upper Rev Pos: Upper reverse position |
- |
| Motor Status | Wiper motor control condition in response to rain sensor request | Normal, Normal (Link Ctrl), Normal (Req Deny), Abnormal or Normal (Wiper Ctrl) | Current motor control condition | - |
| Wiping Mode Signal (Sensor to Wiper) | Status of command request signal for front wiper speed and intermittent time from rain sensor | Stop, LO Mode, HI Mode, Wait, INT Mode1 (Vehicle Stop), INT Mode2 (Vehicle Stop), INT Mode3 (Vehicle Stop), INT Mode4 (Vehicle Stop), INT Mode5 (Vehicle Stop), INT Mode6 (Vehicle Stop), INT Mode7 (Vehicle Stop), INT Mode1 (Vehicle Run), INT Mode2 (Vehicle Run), INT Mode3 (Vehicle Run), INT Mode4 (Vehicle Run), INT Mode5 (Vehicle Run), INT Mode6 (Vehicle Run), INT Mode7 (Vehicle Run), INT Mode (Sensor Abnormal), OFF (Customize) or Fail Stop | Stop: Windshield wiper switch assembly in AUTO position and stop requested (Windshield wiper switch assembly OFF included) (because rain not detected) LO Mode: Windshield wiper switch assembly in AUTO position and LO operation requested HI Mode: Windshield wiper switch assembly in AUTO position and HI operation requested Wait: INT Mode 1 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 32.7 s INT Mode 2 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 17.5 s INT Mode 3 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 9.7 s INT Mode 4 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 5.4 s INT Mode 5 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 3.1 s INT Mode 6 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 1.6 s INT Mode 7 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 0.8 s INT Mode 1 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 17.9 s INT Mode 2 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 10.1 s INT Mode 3 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 5.9 s INT Mode 4 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 3.5 s INT Mode 5 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 2.1 s INT Mode 6 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 1.2 s INT Mode 7 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 0.6 s INT Mode (Sensor Abnormal): Windshield wiper switch assembly in AUTO position and speed sensing intermittent operation requested OFF (Customize): Windshield wiper switch assembly in AUTO position and stop requested (for customization) Fail Stop: Windshield wiper switch assembly in AUTO position and stop requested (sensor malfunction) |
- |
| Wiper LO Single Operation Signal | LO operation condition signal | ON or OFF | ON: Windshield wiper switch assembly in AUTO position and sensor determines small amount of rain while wiper is in stopped position OFF: Windshield wiper switch assembly in AUTO position and wiper in position other than stopped |
- |
| Wiping Mode Signal (Wiper to Sensor) | Response status of command request signal for front wiper speed and intermittent time from rain sensor to windshield wiper motor assembly | Stop, LO Mode, HI Mode, Wait, INT Mode1 (Vehicle Stop), INT Mode2 (Vehicle Stop), INT Mode3 (Vehicle Stop), INT Mode4 (Vehicle Stop), INT Mode5 (Vehicle Stop), INT Mode6 (Vehicle Stop), INT Mode7 (Vehicle Stop), INT Mode1 (Vehicle Run), INT Mode2 (Vehicle Run), INT Mode3 (Vehicle Run), INT Mode4 (Vehicle Run), INT Mode5 (Vehicle Run), INT Mode6 (Vehicle Run), INT Mode7 (Vehicle Run), INT Mode (Sensor Abnormal), OFF (Customize) or Fail Stop | Stop: Windshield wiper switch assembly in AUTO position and stop requested (Windshield wiper switch assembly OFF included) (because rain not detected) LO Mode: Windshield wiper switch assembly in AUTO position and LO operation requested HI Mode: Windshield wiper switch assembly in AUTO position and HI operation requested Wait: INT Mode 1 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 32.7 s INT Mode 2 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 17.5 s INT Mode 3 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 9.7 s aINT Mode 4 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 5.4 s INT Mode 5 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 3.1 s INT Mode 6 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 1.6 s INT Mode 7 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 0.8 s INT Mode 1 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 17.9 s INT Mode 2 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 10.1 s INT Mode 3 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 5.9 s INT Mode 4 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 3.5 s INT Mode 5 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 2.1 s INT Mode 6 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 1.2 s INT Mode 7 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 0.6 s INT Mode (Sensor Abnormal): Windshield wiper switch assembly in AUTO position and speed sensing intermittent operation requested OFF (Customize): Windshield wiper switch assembly in AUTO position and stop requested (for customization) Fail Stop: Windshield wiper switch assembly in AUTO position and stop requested (sensor malfunction) |
- |
| Sensor High Temp History | A history item indicating if the rain sensor temperature was high (approximately 80°C) | OFF or ON | OFF: The rain sensor temperature was not high (approximately 80°C [176°F]) ON: The rain sensor temperature was high (approximately 80°C [176°F]) |
Clearing the DTCs also clears the history |
| Sensor Low Temp History | A history item indicating if the rain sensor temperature was low (approximately -40 °C) | OFF or ON | OFF: The rain sensor temperature was not low (approximately -40°C [-104°F]) ON: The rain sensor temperature was low (approximately -40°C [-104°F]) |
Clearing the DTCs also clears the history |
| Vehicle Speed | Vehicle speed | Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Almost the same as actual vehicle speed | - |
| Auto Wiper | Setting to switch control of automatic wipers/vehicle speed sensing intermittent time adjustment | Avail or Not Avl | Customize setting displayed | - |
| Number of Trouble Code | Number of DTCs | 0 to 255 | When system is normal: 0 When a malfunction is detected: More than 0 |
- |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Washer Switch | Level warning switch assembly state | ON or OFF | ON: Washer fluid level low OFF: Washer fluid level not low |
- |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Wiper OFF Switch | Windshield wiper switch assembly (OFF position) condition | OFF or ON | OFF: Windshield wiper switch assembly not in OFF position ON: Windshield wiper switch assembly in OFF position |
- |
| Wiper Auto/Int Switch | Windshield wiper switch assembly (AUTO position) condition | OFF or ON | OFF: Windshield wiper switch assembly not in AUTO position ON: Windshield wiper switch assembly in AUTO position |
- |
| Wiper Lo Switch | Windshield wiper switch assembly (LO position) condition | OFF or ON | OFF: Windshield wiper switch assembly not in LO position ON: Windshield wiper switch assembly in LO position |
- |
| Wiper Hi Switch | Windshield wiper switch assembly (HI position) condition | OFF or ON | OFF: Windshield wiper switch assembly not in HI position ON: Windshield wiper switch assembly in HI position |
- |
| Wiper Mist Switch | Windshield wiper switch assembly (MIST position) condition | OFF or ON | OFF: Windshield wiper switch assembly not in MIST position ON: Windshield wiper switch assembly in MIST position |
- |
| Washer Switch | Windshield wiper switch assembly (washer switch) condition | OFF or ON | OFF: Windshield wiper switch assembly (washer switch) in OFF position ON: Windshield wiper switch assembly (washer switch) in ON position |
- |
| Rear Wiper Lo Switch | Windshield wiper switch assembly (rear wiper switch LO position) condition | OFF or ON | OFF: Windshield wiper switch assembly (rear wiper switch) not in LO position ON: Windshield wiper switch assembly (rear wiper switch) in LO position |
Although the item is displayed on the GTS, it is not applicable to this vehicle |
| Rear Wiper Hi Switch | Windshield wiper switch assembly (rear wiper switch HI position) condition | OFF or ON | OFF: Windshield wiper switch assembly (rear wiper switch) not in HI position ON: Windshield wiper switch assembly (rear wiper switch) in HI position |
Although the item is displayed on the GTS, it is not applicable to this vehicle |
| Rear Washer Switch | Windshield wiper switch assembly (rear washer switch) condition | OFF or ON | OFF: Windshield wiper switch assembly (rear washer switch) in OFF position ON: Windshield wiper switch assembly (rear washer switch) in ON position |
Although the item is displayed on the GTS, it is not applicable to this vehicle |
| Intermittent Time Volume | Intermittent time adjustment volume condition | Shortest, Shorter, Longer or Longest | Shortest: Windshield wiper switch assembly (intermittent time adjustment volume condition) P4 position Shorter: Windshield wiper switch assembly (intermittent time adjustment volume condition) P3 position Longer: Windshield wiper switch assembly (intermittent time adjustment volume condition) P2 position Longest: Windshield wiper switch assembly (intermittent time adjustment volume condition) P1 position |
- |
| Wiper Spec Info | Specification information | Unknown, Auto spec or Int spec | Unknown: Specification not stored Auto Spec: Automatic wiper control Int Spec: Vehicle speed sensing intermittent time adjustment control |
- |
| The Number of DTCs | Number of DTCs | 0 to 255 | When system is normal: 0 When a malfunction is detected: More than 0 |
- |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Front Window Washer Switch | Windshield wiper switch assembly (washer switch) condition | OFF or ON | OFF: Windshield wiper switch assembly (washer switch) off ON: Windshield wiper switch assembly (washer switch) on |
- |
| Headlight Cleaner Switch | Headlight cleaner switch condition | OFF or ON | OFF: Headlight cleaner switch off ON: Headlight cleaner switch on |
Although the item is displayed on the GTS, it is not applicable to this vehicle |
ACTIVE TEST
Tech Tips
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Turn the power switch off.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / (desired system) / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wiper Motor LO | Operates the windshield wiper motor assembly and No. 2 windshield wiper motor assembly in LO | OFF or ON | - |
| Wiper Motor HI | Operates the windshield wiper motor assembly and No. 2 windshield wiper motor assembly in HI | OFF or ON | - |
| Front Washer | Operates the open side washer | OFF or ON | - |
| Rear Washer | Operates the closed side washer | OFF or ON | - |
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wiper Power Relay | Operates the windshield wiper switch relay (WIPER NO.1) and windshield wiper switch relay (WIPER NO.2) | OFF or ON | - |
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Headlight Cleaner | Operate headlight cleaner motor and pump assembly | OFF or ON | - |