WIPER AND WASHER SYSTEM FREEZE FRAME DATA


  1. FREEZE FRAME DATA


    1. Whenever a DTC is detected, the windshield wiper motor assembly stores the current vehicle state as Freeze Frame Data.

  2. CHECK FREEZE FRAME DATA


    1. Turn the power switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the power switch on (IG).

    4. Turn the GTS on.

    5. Enter the following menus: Body Electrical / Wiper / Trouble Codes.


      Body Electrical > Wiper > Trouble Codes
      Body Electrical > Wiper
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Wiper Switch HI (Line) Windshield wiper switch assembly HI signal (abnormal control system) input condition OFF or ON

      OFF: Windshield wiper switch assembly not in HI position

      ON: Windshield wiper switch assembly in HI position

      		 -
      Wiper Stop Position Displays windshield wiper motor assembly stop position Store Are, Lower Rev Pos, Wipe Area or Upper Rev Pos

      Store Are/Lower Rev Pos: Lower reverse position or lower

      Lower Rev Pos: Lower reverse position or lower reverse position or less

      Wipe Area: Between lower reverse position and upper reverse position

      Upper Rev Pos: Upper reverse position

      		 -
      Wiper Position Displays the wiper position Store Are, Exchange Position or Wipe Area

      Store Area: Lower reverse position

      Exchange Position: Service position

      Wipe Area: Lower reverse position higher or upper reverse position or less

      		 -
      Status of Motor Lock Windshield wiper motor assembly stuck malfunction condition Normal or Lock

      Normal: Normal operation possible

      Lock: Operation unavailable

      		 -
      Status of Temperature Protection Condition of temperature protection control for the windshield wiper motor assembly Normal, LO Operation, INT Operation or Stop

      Normal: Motor temperature less than 95°C (203°F)

      LO Operation: Motor temperature 95°C (203°F) or more

      INT Operation: Motor temperature 100°C (212°F) or more

      Stop: Motor temperature 105°C (221°F) or more

      		 -
      Status of Overvoltage Windshield wiper motor assembly voltage condition Normal or Overvoltage

      Normal: Normal operation possible

      Overvoltage: Operation unavailable

      		 -
      Status of Low Voltage Windshield wiper motor assembly voltage condition Normal or Low Voltage

      Normal: Normal operation possible

      Low Voltage: Operation unavailable

      		 -
      Motor Shaft Angle Displays windshield wiper motor assembly rotation angle 0 to 255 ° Displays windshield wiper motor assembly rotation angle

      Tech Tips


      • Upper reverse position: 83.1°

      • Retracted position or lower than the retracted position: 0°
      Motor Temperature Displays windshield wiper motor assembly internal temperature sensor value Min.: -128°C (-262°F), Max.: 128°C (262°F) Displays windshield wiper motor assembly internal temperature sensor value -
      Motor Current Displays windshield wiper motor assembly current 0 to 63 A Displays windshield wiper motor assembly current -
      Motor Power Supply Voltage Displays windshield wiper motor assembly voltage 0 to 63 V Displays windshield wiper motor assembly voltage -
      Wiper Stop Position (Sub Motor) Displays No. 2 windshield wiper motor assembly stop position Store Are, Lower Rev Pos, Wipe Area or Upper Rev Pos

      Lower Rev Pos: Lower reverse position or lower reverse position or less

      Wipe Area: Above or below the upper reverse position from the lower reverse position

      Upper Rev Pos: Upper reverse position or higher

      		 -
      Status of Motor Lock (Sub Motor) No. 2 windshield wiper motor assembly stuck malfunction condition Normal or Lock

      Normal: Normal operation possible

      Lock: Operation unavailable

      		 -
      Status of Temperature Protection (Sub Motor) Condition of temperature protection control for the No. 2 windshield wiper motor assembly Normal, LO Operation, INT Operation or Stop

      Normal: Motor temperature less than 95°C (203°F)

      LO Operation: Motor temperature 95°C (203°F) or more

      INT Operation: Motor temperature 100°C (212°F) or more

      Stop: Motor temperature 105°C (221°F) or more

      		 -
      Status of Overvoltage (Sub Motor) No. 2 windshield wiper motor assembly voltage condition Normal or Overvoltage

      Normal: Normal operation possible

      Overvoltage: Operation unavailable

      		 -
      Status of Low Voltage (Sub Motor) No. 2 windshield wiper motor assembly voltage condition Normal or Low Voltage

      Normal: Normal operation possible

      Low Voltage: Operation unavailable

      		 -
      Motor Shaft Angle (Sub Motor) Displays No. 2 windshield wiper motor assembly rotation angle 0 to 255 ° Displays No. 2 windshield wiper motor assembly rotation angle

      Tech Tips


      • Upper reverse position: 85.8°

      • Retracted position or lower than the retracted position: 0°
      Motor Temperature (Sub Motor) Displays No. 2 windshield wiper motor assembly internal temperature sensor value Min.: -128°C (-262°F), Max.: 128°C (262°F) Displays No. 2 windshield wiper motor assembly internal temperature sensor value -
      Motor Current (Sub Motor) Displays No. 2 windshield wiper motor assembly current 0 to 63 A Displays No. 2 windshield wiper motor assembly current -
      Motor Power Supply Voltage (Sub Motor) Displays No. 2 windshield wiper motor assembly voltage 0 to 63 V Displays No. 2 windshield wiper motor assembly voltage -
      Number of DTCs Number of trouble codes 0 to 255

      When system is normal: 0

      When a malfunction is detected: More than 0

      		 -