BACK WINDOW GLASS REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the back window glass removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point LKA/LDA system

Click here

Pre-collision system
Parking assist monitor system

Click here

Steering sensor zero point calibration Variable gear ratio steering system

Click here

Front seat assembly LH (Only for removal and installation) Initialize position control ECU Front Power Seat Control System

Click here

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

    Click here

    B004CGW

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

    Tech Tips

    When the cable is disconnected/reconnected to the negative (-) auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

  2. REMOVE NO. 2 DECK BOARD

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    B004A52

    Click here

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE ROOF HEADLINING ASSEMBLY

    Click here

  5. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY

    Click here

  6. REMOVE ANTENNA ASSEMBLY WITH HOLDER

    Click here

  7. REMOVE CENTER STOP LIGHT ASSEMBLY

    Click here

  8. REMOVE ROOF DRIP SIDE FINISH MOULDING LH

    Click here

  9. REMOVE ROOF DRIP SIDE FINISH MOULDING RH

    Tech Tips

    Use the same procedure described for the LH side.

  10. REMOVE UPPER QUARTER WINDOW MOULDING LH

    Click here

  11. REMOVE UPPER QUARTER WINDOW MOULDING RH

    Tech Tips

    Use the same procedure described for the LH side.

  12. REMOVE REAR ROOF SIDE GARNISH SUB-ASSEMBLY LH

    Click here

  13. REMOVE REAR ROOF SIDE GARNISH SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  14. REMOVE NO. 1 DECK BOARD

    Click here

  15. REMOVE LUGGAGE COMPARTMENT TRIM COVER LH

    Click here

  16. REMOVE LUGGAGE COMPARTMENT TRIM COVER RH

    Click here

  17. REMOVE SIDE TRIM BOX

    Click here

  18. REMOVE REAR FLOOR FINISH PLATE

    Click here

  19. REMOVE LUGGAGE COMPARTMENT TRIM BOX

    Click here

  20. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

    Click here

  21. REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER

    Click here

  22. REMOVE INNER LUGGAGE COMPARTMENT TRIM COVER RH

    Click here

  23. REMOVE INNER LUGGAGE COMPARTMENT TRIM COVER LH

    Click here

  24. REMOVE REAR COMBINATION LIGHT BODY BRACKET LH

    Click here

  25. REMOVE REAR COMBINATION LIGHT BODY BRACKET RH

    Tech Tips

    Use the same procedure described for the LH side.

  26. REMOVE UPPER NO. 1 LUGGAGE COMPARTMENT COVER RH

    Click here

  27. REMOVE UPPER NO. 1 LUGGAGE COMPARTMENT COVER LH

    Click here

  28. REMOVE LUGGAGE COMPARTMENT DOOR HINGE COVER RH

    Click here

  29. REMOVE LUGGAGE COMPARTMENT DOOR HINGE COVER LH

    Click here

  30. REMOVE NO. 4 LUGGAGE ROOM WIRE

    Click here

  31. REMOVE WIRE HARNESS GROMMET

    Click here

  32. REMOVE LOWER BACK WINDOW OUTSIDE MOULDING

    Click here

  33. REMOVE BACK WINDOW GLASS

    Note


    • The back window glass may fall while performing this procedure. Therefore, use suction cups to hold the back window glass from the outside of the vehicle.The back window glass may fall while performing this procedure. Therefore, use suction cups to hold the back window glass from the outside of the vehicle.

    • Be careful not to damage the back window glass when cutting as the back window spacers are installed to the back window glass.


    1. Disconnect each connector.

    2. B004BSOC01
      B004CG0 Protective Tape

      Apply protective tape to the outer surface of the vehicle body to prevent scratches.

    3. B004CKIC01
      *a Cut Off

      Using a knife, cut off the upper outside back window moulding LH as shown in the illustration.

      Note


      • Do not damage the back window glass or body panel.

      • If the body panel is damaged, perform rust-prevention treatment after removing the back window glass.

      Tech Tips

      Use the same procedure for both upper outside back window moulding RH.

    4. When reusing the windshield glass:


      1. B004C3KC01
        *a Matchmarks

        Place matchmarks over the glass and vehicle body at the locations indicated in the illustration.

      2. Install the suction cups to the windshield glass.

    5. B0049SVC01
      *1 Back Window Glass Spacer
      *2 No. 1 Back Window Glass Spacer
      *3 No. 2 Back Window Glass Spacer
      *a Piano Wire

      From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.

    6. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

      Note

      When separating the glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

    7. Cut through the adhesive by pulling the piano wire around the glass.(Leave back window glass spacer LH)

      Note


      • When working near the back window glass connector, be careful not to damage it with the piano wire.

      • Leave as much adhesive on the vehicle body as possible when cutting through the adhesive.

    8. Using suction cups, remove the windshield glass.

      Note

      Do not drop the back window glass.

  34. REMOVE NO. 1 REAR WINDOW WIRE


    1. B004AG3C01
      *a Backside

      Detach the connector, remove the No. 1 rear window wire.

      Note

      Do not damage the back window glass.

  35. REMOVE UPPER OUTSIDE BACK WINDOW MOULDING LH


    1. When reusing the back window glass:


      1. B004C4TC01
        *a Backside

        Using a gasket scraper, remove the upper outside back window moulding LH from the back window glass.

        Note


        • Do not damage the back window glass.

        • Be sure to replace the upper outside back window moulding LH with a new one.

  36. REMOVE UPPER OUTSIDE BACK WINDOW MOULDING RH


    1. When reusing the back window glass:


      1. B004CBXC01
        *a Backside

        Using a gasket scraper, remove the upper outside back window moulding RH from the back window glass.

        Note


        • Do not damage the back window glass.

        • Be sure to replace the upper outside back window moulding RH with a new one.

  37. REMOVE WINDOW GLASS ADHESIVE DAM


    1. When reusing the back window glass:


      1. B004CR1C01
        *a Backside

        Using a gasket scraper, remove the 8 window glass adhesive dams from the back window glass.

        Note


        • Do not damage the back window glass.

        • Be sure to replace the window glass adhesive dam with a new one.

  38. REMOVE BACK WINDOW GLASS ADHESIVE DAM


    1. When reusing the back window glass:


      1. B004A9CC01
        *a Backside

        Using a gasket scraper, remove the back window glass adhesive dams from the back window glass.

        Note


        • Do not damage the back window glass.

        • Be sure to replace the back window glass adhesive dam with a new one.

  39. REMOVE CENTER STOP LIGHT BRACKET LH


    1. When reusing the back window glass:


      1. B004CTXC01
        *a Backside

        Using a gasket scraper, remove the center stop light bracket LH from the back window glass.

        Note


        • Do not damage the back window glass.

        • Be sure to replace the center stop light bracket LH with a new one.

  40. REMOVE CENTER STOP BRACKET


    1. When reusing the back window glass:


      1. B004BK7C01
        *a Backside

        Using a gasket scraper, remove the center stop bracket from the back window glass.

        Note

        Do not damage the back window glass.

  41. REMOVE LIGHT WIRE


    1. When reusing the back window glass:


      1. B004BT6C01
        *a Backside

        Using a gasket scraper, remove the light wire from the back window glass.

        Note


        • Do not damage the back window glass.

        • Be sure to replace the light wire with a new one.

  42. REMOVE BACK WINDOW GLASS SPACER


    1. When reusing the back window glass:


      1. B004A5HC01
        *a Backside

        Using a gasket scraper, remove the back window glass spacer from the back window glass.

        Note


        • Do not damage the back window glass.

        • Be sure to replace the back window glass spacer with a new one.

  43. REMOVE NO. 1 BACK WINDOW GLASS SPACER


    1. When reusing the back window glass:


      1. B004APIC01
        *a Backside

        Using a gasket scraper, remove the No. 1 back window glass spacer from the back window glass.

        Note


        • Do not damage the back window glass.

        • Be sure to replace the No. 1 back window glass spacer with a new one.

  44. REMOVE NO. 2 BACK WINDOW GLASS SPACER


    1. When reusing the back window glass:


      1. B004BBLC01
        *a Backside

        Using a gasket scraper, remove the No. 2 back window glass spacer from the back window glass.

        Note


        • Do not damage the back window glass.

        • Be sure to replace the No. 2 back window glass spacer with a new one.