INSTRUMENT PANEL SAFETY PAD DISASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. REMOVE ANTENNA CORD SUB-ASSEMBLY

    Click here

  2. REMOVE NO. 3 HEATER TO REGISTER DUCT


    1. B000Q9XN01

      Remove the 3 screws <F> or <H>.

    2. Detach the guides and remove the No. 3 heater to register duct.

  3. REMOVE NAVIGATION ANTENNA ASSEMBLY WITH BRACKET

    Click here

  4. REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

    Click here

  5. REMOVE AUTOMATIC LIGHT CONTROL SENSOR

    Click here

  6. REMOVE NO. 1 HEATER TO REGISTER DUCT


    1. B000QFVN01

      Remove the 2 screws <F> or <H> and No. 1 heater to register duct.

  7. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. B000SBNC01
      B004C4F Screw
      B004ANI Connector

      Remove the 4 screws <H>.

    2. Detach the guides and remove the No. 1 instrument panel register assembly.

    3. Disconnect the connector.

  8. REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY


    1. B000OAPC01
      B004B1M Remove in this Direction

      Detach the claws and remove the No. 1 speaker opening cover assembly.

    2. Disconnect the connector.

  9. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY


    1. B000RJJC01
      B004C4F Screw
      B004ANI Connector

      Remove the 2 screws.

    2. Disconnect the connector and remove the front No. 2 speaker assembly.

      Note

      Do not touch the cone part of the front No. 2 speaker assembly.

  10. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY MAIN


    1. B000T4E

      Remove the screw.

    2. Detach the claw and guide and remove the instrument panel sub-assembly main.

  11. REMOVE DEFROSTER NOZZLE ASSEMBLY


    1. B000RQWN01

      Remove the 3 screws <H> or <F>.

    2. Detach the guides and remove the defroster nozzle assembly.

  12. REMOVE NO. 1 INSTRUMENT PANEL PIN


    1. B000OP9C01
      B004B1M Remove in this Direction

      Remove the screw.

    2. Detach the guide in the direction of the arrow shown in the illustration and remove the No. 1 instrument panel pin.

      Tech Tips

      Use the same procedure to remove the No. 1 instrument panel pin on the other side.

  13. REMOVE NO. 2 INSTRUMENT PANEL WIRE


    1. Detach the clamps and remove the No. 2 instrument panel wire.

      B000SRY

  14. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. B000PHK

      Remove the 24 screws.

    2. Detach the claws and remove the upper instrument panel finish panel sub-assembly.

  15. REMOVE NO. 1 DEFROSTER NOZZLE GARNISH


    1. B000PYCC01
      B004B1M Remove in this Direction (1)
      B004CNL Remove in this Direction (2)

      Remove the 4 screws.

    2. Detach the claws and guides in the direction of the arrow shown in the illustration and remove the No. 1 defroster nozzle garnish.

  16. REMOVE GLOVE COMPARTMENT DOOR LOCK COVER

    Note

    Only perform this procedure when removing and installing the glove compartment door lock cylinder assembly. Furthermore, always replace the glove compartment door assembly with a new one when performing this procedure.


    1. B000RW4

      Using a screwdriver, cut the claws and remove the glove compartment door lock cover.

  17. REMOVE GLOVE COMPARTMENT DOOR LOCK CYLINDER ASSEMBLY

    Note

    Always replace the glove compartment door assembly with a new one when performing this procedure.


    1. B000OYDC01
      *1 Cylinder Lock
      B004B1M Remove in this Direction

      Press the cylinder lock to release it and pull out the glove compartment door lock cylinder assembly from the glove compartment door assembly to remove it as shown in the illustration.