FRONT SEAT OUTER BELT ASSEMBLY INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL FRONT SEAT BELT RETRACTOR COVER LH


    1. B004B9UC01
      B004B1M Install in this Direction (1)
      B004CNL Install in this Direction (2)

      Slide in the installation direction (1) shown in the illustration to attach the guide.

    2. Push in the installation direction (2) shown in the illustration to attach the claw and install the front seat belt retractor cover LH.

  2. INSPECT FRONT SEAT OUTER BELT ASSEMBLY LH

    Click here

  3. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH


    1. B004C7SN01

      Attach the guides and temporarily install the front seat outer belt assembly LH.

    2. Install the 2 bolts.

      Torque:
      Bolt A
      12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }
      Bolt B
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. B004CCZC01
      *a Locking Button
      *b Lock

      Connect the pretensioner connector and lock the locking button as shown in the illustration.

      Note


      • When handling the pretensioner connector, take care not to damage the pretensioner wire harness.

      • Securely lock the locking button.

    4. Connect the tension reducer connector.

    5. B004BWQ

      Install the shoulder anchor of the front seat outer belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  4. INSTALL NO. 4 HYBRID BATTERY INTAKE DUCT

    Click here

  5. INSTALL NO. 3 HYBRID BATTERY INTAKE DUCT

    Tech Tips

    Use the same procedure described for the No. 1 hybrid battery intake duct.

    Click here

  6. INSTALL CENTER PILLAR GARNISH ASSEMBLY LH

    Click here

  7. INSTALL QUARTER TRIM PANEL ASSEMBLY LH

    Click here

  8. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH(FLOOR ANCHOR)


    1. B004CUEC01
      *a Tongue Plate
      *b Floor Anchor

      Install the floor anchor of the front seat outer belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      When connecting the floor anchor of the front seat outer belt assembly LH, make sure that the tongue plate is facing the front of the vehicle.

    2. Check that the ELR locks.


      1. With the front seat outer belt assembly installed to the vehicle, check that the belt locks when it is pulled out quickly.

  9. INSTALL OUTER LAP BELT ANCHOR COVER


    1. B004A5KC01
      *a Guide A
      *b Guide B
      B004B1M Install in this Direction (1)
      B004CNL Install in this Direction (2)

      Slide in the installation direction (1) shown in the illustration to attach the guide B.

    2. Push in the installation direction (2) shown in the illustration to attach the guide A and install the outer lap belt anchor cover.

  10. INSTALL FRONT DOOR SCUFF PLATE LH

    Click here

  11. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

    Click here

  12. INSTALL QUARTER INSIDE TRIM BOARD LH

    Click here

  13. INSTALL REAR SEATBACK ASSEMBLY LH

    Click here

  14. INSTALL REAR SEATBACK COVER

    Click here

  15. INSTALL REAR SEAT SIDE GARNISH

    Click here

  16. INSTALL REAR SEAT CUSHION LOCK HOOK

    Click here

  17. INSTALL REAR SEAT CUSHION ASSEMBLY

    Click here

  18. INSTALL FRONT SEAT ASSEMBLY LH

    Click here

  19. INITIALIZATION OF SEAT ECU

    Click here

  20. INSPECT SEAT BELT WARNING SYSTEM

    Click here

  21. INSPECT SRS WARNING LIGHT

    Click here