POP UP HOOD LIFTER(for Rear Side) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the No. 2 pop up hood lifter assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure	Necessary Procedures	Effects / Inoperative when not Performed	Link
Disconnect cable from negative (-) auxiliary battery terminal	Memorize steering angle neutral point	LKA/LDA system	Click here
		Pre-collision system	Click here
		Parking assist monitor system	Click here
	Steering sensor zero point calibration	Variable gear ratio steering system	Click here

CAUTION:

If the hood release lever is pulled after the No. 2 pop up hood lifter assembly is activated, the hood may rise more.

Tech Tips

Use the same procedure as for the RHD and LHD vehicles.
The procedure listed below is for the LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.

PROCEDURE

PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click here

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here
REMOVE NO. 2 DECK BOARD

Click here
DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Click here
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If the airbag deploys for any reason, it may cause a serious accident.
Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here
REMOVE ENGINE ROOM SIDE COVER LH

Click here
REMOVE RADIATOR SUPPORT TO FRAME SEAL RH

Click here
REMOVE LOWER RADIATOR AIR DEFLECTOR

Click here
REMOVE FRONT FENDER REINFORCEMENT SUB-ASSEMBLY TOP LH

Click here
REMOVE NO. 3 COWL TOP PANEL INSULATOR (for LH Side)

for LHD:

Click here

for RHD:

Click here
REMOVE NO. 2 COWL TOP PANEL INSULATOR (for RH Side)

for LHD:

Click here

for RHD:

Click here

REMOVE NO. 2 POP UP HOOD LIFTER ASSEMBLY LH

CAUTION:

Extended Section

When storing the No. 2 pop up hood lifter assembly LH, keep the No. 2 pop up hood lifter assembly LH extended section side facing upward.
If the No. 2 pop up hood lifter assembly LH deploys for any reason, it may cause a serious accident.

Check that the power switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If the pop up hood lifter assembly deploys for any reason, it may cause a serious accident.

*a	Housing Lock
*b	CPA
*c	CPA Upper Part
	Slide

Disconnect pop up hood lifter assembly LH connector.

Note

When disconnecting any pop up hood lifter assembly LH connector, take care not to damage the wire harness.

Push down the housing lock and slide the CPA. (At this time, the connector cannot be disconnected yet.)
Push the housing lock again and disconnect the connector.

Note

Do not push down the upper part of the CPA shown in the illustration when disconnecting the pop up hood lifter assembly LH connector.

After disconnecting the connector, check that the position of the housing lock is correct as shown in the illustration.

*a	Correct	*b	Incorrect
*c	CPA	*d	Housing

Remove the 2 nuts.
Detach the clamps and remove the No. 2 pop up hood lifter assembly LH.