POP UP HOOD LIFTER(for Front Side) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the pop up hood lifter assembly LH/RH removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point LKA/LDA system

Click here

Pre-collision system
Parking assist monitor system

Click here

Steering sensor zero point calibration Variable gear ratio steering system

Click here

CAUTION:

If the hood release lever is pulled after the pop up hood lifter assembly is activated, the hood may rise more.

Tech Tips


  • Use the same procedure as for the RHD and LHD vehicles.

  • The procedure listed below is for the LHD vehicles.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read precaution thoroughly before servicing.

    Click here

    B004CGW

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. REMOVE NO. 2 DECK BOARD

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    B004A52

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE FRONT AIRBAG SENSOR LH (for LH Side)

    Click here

  5. REMOVE FRONT AIRBAG SENSOR RH (for RH Side)

    Tech Tips

    Use the same procedure for the LH side.

  6. REMOVE HOOD LOCK RELEASE LEVER PROTECTOR (for RH Side)

    Click here

  7. REMOVE HOOD LOCK CONTROL CABLE COVER RH (for RH Side)

    Click here

  8. REMOVE HOOD LOCK CONTROL ASSEMBLY (for RH Side)


    1. B004A1DC01
      *A for LHD
      *B for RHD
      *a End of Hood Lock Control Assembly
      B004B1M Remove in this Direction

      Disconnect the clamp.

    2. Move the end of the hood lock control assembly in the direction of the arrow shown in the illustration and detach it from the hood lock assembly.

  9. REMOVE POP UP HOOD LIFTER ASSEMBLY LH

    CAUTION:


    • When storing the pop up hood lifter assembly LH even temporarily, be sure to keep the extended section side facing upward.

    • If the pop up hood lifter assembly LH deploys for any reason, it may cause a serious accident.

    B004BIIC01
    B004CG0 Extended Section

    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:


      • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

      B004A52
    3. B004C3H

      Detach the 2 clamps.

    4. B004B37C01
      *a Housing Lock
      *b CPA
      B004B1M Slide

      Disconnect pop up hood lifter assembly LH connector.

      Note

      When disconnecting pop up hood lifter assembly LH connector, take care not to damage the wire harness.


      1. Push down the housing lock and slide the CPA. (At this time, the connector cannot be disconnected yet.)

      2. Push the housing lock again and disconnect the connector.

        Note

        Do not push down the upper part of the CPA shown in the illustration when disconnecting the pop up hood lifter assembly LH connector.

      3. After disconnecting the connector, check that the position of the housing lock is correct as shown in the illustration.

        B004AD8C07
        *a Correct *b Incorrect
        *c CPA *d Housing
    5. B004CLW

      Remove the 3 bolts.

    6. B004BW8C01
      B0049X5 Place Hands Here
      B004B1M Remove in this Direction (1)
      B004CNL Remove in this Direction (2)

      Move the pop up hood lifter assembly LH in the direction of the arrow shown in the illustration direction (1) and detach the hook.

    7. Place your hand at the position shown in the illustration and move the pop up hood lifter assembly LH in the direction of the arrow shown in the illustration direction (2), pull out the pop up hood lifter assembly LH.

      Note

      When pulling out the pop up hood lifter assembly LH, do not pull the wire harness.

  10. REMOVE POP UP HOOD LIFTER ASSEMBLY RH

    CAUTION:


    • When storing the horn button assembly, keep the airbag deployment side facing upward.

    • If the pop up hood lifter assembly LH operates for any reason, it may cause a serious accident.

    B004BIIC01
    B004CG0 Extended Section

    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:


      • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

      B004A52

    3. Disconnect pop up hood lifter assembly RH connector.

      Note

      When disconnecting pop up hood lifter assembly RH connector, take care not to damage the wire harness.


      1. B004B37C01
        *a Housing Lock
        *b CPA
        *c CPA Upper Part
        B004B1M Slide

        Push down the housing lock and slide the CPA. (At this time, the connector cannot be disconnected yet.)

      2. Push the housing lock again and disconnect the connector.

        Note

        Do not push down the upper part of the CPA shown in the illustration when disconnecting the pop up hood lifter assembly RH connector.

      3. After disconnecting the connector, check that the position of the housing lock is correct as shown in the illustration.

        B004AD8C07
        *a Correct *b Incorrect
        *c CPA *d Housing
    4. B004B7SC01
      B004C4F Bolt

      Remove the 3 bolts.

    5. B004CQ7C02
      B0049X5 Place Hands Here
      B004B1M Remove in this Direction(1)
      B004CNL Remove in this Direction(2)

      Move the pop up hood lifter assembly RH in the direction of the arrow shown in the illustration direction (1) and detach the hook.

      Note

      When pulling out the pop up hood lifter assembly RH, do not pull the wire harness.

    6. Place your hand at the position shown in the illustration and move the pop up hood lifter assembly RH in the direction of the arrow shown in the illustration direction (2), pull out the pop up hood lifter assembly RH and remove it.

    7. B004AN4C01
      *a End of Hood Lock Control Assembly
      B004B1M Remove in this Direction

      Disconnect the clamp.

    8. Move the end of the hood lock control assembly in the direction of the arrow shown in the illustration and remove it from the pop up hood lifter assembly RH.