ENTRY AND START SYSTEM(for Start Function) Security Indicator Light Does not Blink

DESCRIPTION


WIRING DIAGRAM

B0049ZQE15
*1 Main Body ECU (Multiplex Network Body ECU)
*2 Integration Control and Panel Assembly (Security Indicator Light)
*3 Certification ECU (Smart Key ECU Assembly)
*4 CAN Communication Line

CAUTION / NOTICE / HINT

Note


  • When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

    Click here

  • Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to the Service Bulletin.

  • Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

  • After completing repairs, confirm that the problem does not recur.

  • After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

PROCEDURE


  1. CHECK FOR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Entry&Start / Trouble Codes.

    5. Check for DTCs.


      Body Electrical > Entry&Start > Trouble Codes
      Powertrain > Hybrid Control > Trouble Codes
      OK
      DTCs are not output.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO DIAGNOSTIC TROUBLE CODE CHART Click here

    OK

  2. PERFORM ACTIVE TEST USING GTS (IMMOBILISER INDICATOR)


    1. Enter the following menus: Body Electrical / Entry&Start / Active Test.

    2. Perform the Active Test according to the display on the GTS.


      Body Electrical > Entry&Start > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Immobiliser Indicator Security indicator light OFF/ON -

      Body Electrical > Entry&Start > Active Test
      Tester Display
      Immobiliser Indicator
      OK
      The security indicator light (integration control and panel assembly) operates normally.
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SECURITY INDICATOR LIGHT (INTEGRATION CONTROL AND PANEL ASSEMBLY)) Click here

    OK

  3. CHECK SECURITY INDICATOR LIGHT (INTEGRATION CONTROL AND PANEL ASSEMBLY) OPERATION


    1. When the immobiliser is set, check that the security indicator light (integration control and panel assembly) blinks.*1

      OK
      The security indicator light (integration control and panel assembly) blinks normally.

    2. When the theft deterrent system is in the arming preparation state, check that the security indicator light (integration control and panel assembly) illuminates.*2

      OK
      The security indicator light (integration control and panel assembly) illuminates normally.
      Result
      Result Proceed to
      *1 is NG (*2 is OK) A
      *2 is NG (*1 is OK) B

    A

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    B

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

  4. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SECURITY INDICATOR LIGHT (INTEGRATION CONTROL AND PANEL ASSEMBLY))


    1. Disconnect the P66 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the P73 security indicator light (integration control and panel assembly) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P66-20 (IND) - P73-7 (LP) Always Below 1 Ω
      P66-20 (IND) or P73-7 (LP) - Other terminals and body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


    1. Reconnect the P66 certification ECU (smart key ECU assembly) connector.

    2. Reconnect the P73 security indicator light (integration control and panel assembly) connector.

    3. Using an oscilloscope, check the waveform.

      B004BQTC47
      *a

      Component with harness connected

      (Certification ECU (Smart Key ECU Assembly))

      		 - -
      Measurement Condition
      Tester Connection Switch Condition Specified Condition
      P66-20 (IND) - Body ground Power switch off → on (IG) Pulse generation → Below 2 V
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE SECURITY INDICATOR LIGHT (INTEGRATION CONTROL AND PANEL ASSEMBLY) Click here

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)