ENTRY AND START SYSTEM(for Start Function) TERMINALS OF ECU


  1. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    B004AAPE12

    1. Disconnect the X23 and P66 certification ECU (smart key ECU assembly) connectors.

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Tech Tips

      Measure the values on the wire harness side with the connector disconnected.

      Tester Connection Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
      X23-25 (STP1) - Body ground R - Body ground Input Stop light switch signal Brake pedal depressed → Brake pedal released 9 V or higher → 1 V or less

      Power Source Control


      • Stop Light Switch1
      P66-4 (+B) - P66-18 (E) W - W-B Input Power source Power switch off 11 to 14 V -
      P66-15 (CUTB) - Body ground P - Body ground Input Dark current cut pin* Power switch off 11 to 14 V -
      P66-18 (E) - Body ground W-B - Body ground - Ground Always Below 1 Ω -
      P66-21 (SSW2) - Body ground G - Body ground Input

      SSW2 contact signal

      Tech Tips

      Backup for SSW1. Behaves the same way as SSW1.

      		 Power switch pushed → Power switch not pushed Below 15 Ω → 10 kΩ or higher

      Power Source Control


      • Start Switch2
      P66-23 (SSW1) - Body ground V - Body ground Input SSW1 contact signal Power switch pushed → Power switch not pushed Below 15 Ω → 10 kΩ or higher

      Power Source Control


      • Start Switch1
      P66-19 (SPD) - Body ground SB - Body ground Input Vehicle speed signal Always 30 kΩ or higher

      Power Source Control


      • Vehicle Speed Signal

      • *: In order to prevent the vehicle auxiliary battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is installed in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle auxiliary battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of radio waves every 0.25 seconds, which form the detection area, stops).

    3. Reconnect the X23 and P66 certification ECU (smart key ECU assembly) connectors.

    4. Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

      Tester Connection Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
      X23-25 (STP1) - P66-18 (E) R - W-B Input Stop light switch signal Brake pedal released → Brake pedal depressed 1 V or less → 9 V or higher

      Power Source Control


      • Stop Light Switch1
      P66-14 (SLP) - P66-18 (E) R - W-B Input Steering lock position signal Steering locked → Steering unlocked 11 to 14 V → 1.5 V or less

      Power Source Control


      • Steering Unlock Switch
      P66-25 (SLR+) - P66-18 (E) G - W-B Output

      Steering lock motor operation command signal

      (Steering lock motor operation permission signal sent from the certification ECU (smart key ECU assembly))

      When a door is opened, the steering lock motor will be operated if all of the following conditions are met:


      • The steering is unlocked.

      • The power switch is off.

      • The shift state park (P).

      Pulse generation

      (See waveform 1)

      		 -
      P66-13 (LIN) - P66-18 (E) G - W-B Input/Output LIN communication line Power switch on (IG) Pulse generation

      Entry&Start


      • Steering Lock Start Cond
      P66-3 (IGB) - P66-18 (E) LG - W-B Output IGB signal Power switch off → Power switch on (IG) 1 V or less → 8.5 V or higher -
      P66-22 (P) - P66-18 (E) LG - W-B Input P position signal

      Procedure:


      1. Power switch on (IG)

      2. Shift state park (P)

      Pulse generation

      (See waveform 7)

      Power Source Control


      • Shift P Signal
      P66-21 (SSW2) - P66-18 (E) G - W-B Input

      SSW2 contact signal

      Tech Tips

      Backup for SSW1. Behaves the same way as SSW1.

      		 Power switch not pushed → Power switch pushed 9 V or higher → 1 V or less

      Power Source Control


      • Start Switch2
      P66-23 (SSW1) - P66-18 (E) V - W-B Input SSW1 contact signal Power switch not pushed → Power switch pushed 9 V or higher → 1 V or less

      Power Source Control


      • Start Switch1
      P66-16 (ACCD) - P66-18 (E) SB- W-B Output ACC signal Power switch off → Power switch on (ACC) 1 V or less → 8.5 V or higher

      Power Source Control


      • ACC Relay Monitor
      P66-17 (IG1D) - P66-18 (E) B - W-B Output IG1 signal Power switch on (ACC) → Power switch on (IG) 1 V or less → 9 V or higher

      Power Source Control


      • IG Relay Monitor (Outside)
      P66-19 (SPD) - P66-18 (E) SB - W-B Input Vehicle speed signal Vehicle being driven at approximately 5 km/h (3 mph)

      Pulse generation

      (See waveform 2)

      Power Source Control


      • Vehicle Speed Signal
      P66-27 (ST2) - P66-18 (E) BR - W-B Output Starter request signal With the brake pedal depressed, the power switch is pressed and held → After approximately 3 sec. has elapsed, the power switch is released 8.5 V or higher → 1 V or less -
      P66-8 (CLG5) - P66-18 (E) GR - W-B Output Output to No. 1 indoor electrical key antenna assembly (front floor)

      Procedure:


      1. Power switch off

      2. Electrical key transmitter sub-assembly not inside vehicle

      3. Within 30 seconds of closing any door

      Pulse generation

      (See waveform 3)

      		 -
      P66-9 (CG5B) - P66-18 (E) B - W-B Output Output to No. 1 indoor electrical key antenna assembly (front floor) (terminal on opposite side of component from CLG5 output terminal)

      Procedure:


      1. Power switch off

      2. Electrical key transmitter sub-assembly not inside vehicle

      3. Within 30 seconds of closing any door

      Pulse generation

      (See waveform 3)

      		 -
      X23-5 (CLG6) - P66-18 (E) BE - W-B Output Output to No. 1 indoor electrical key antenna assembly (rear floor)

      Procedure:


      1. Power switch off

      2. Electrical key transmitter sub-assembly not inside vehicle

      3. Within 30 seconds of closing any door

      Pulse generation

      (See waveform 3)

      		 -
      X23-6 (CG6B) - P66-18 (E) L - W-B Output Output to No. 1 indoor electrical key antenna assembly (rear floor) (terminal on opposite side of component from CLG6 output terminal)

      Procedure:


      1. Power switch off

      2. Electrical key transmitter sub-assembly not inside vehicle

      3. Within 30 seconds of closing any door

      Pulse generation

      (See waveform 3)

      		 -
      P66-5 (TXCT) - P66-11 (AGND) W - L Output Signal output to transponder key amplifier Power switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V

      Entry&Start


      • BCC Malfunction

      • Abnormal Status

      • Different Encrypt Code

      • Different Serial Number

      • Frame Error

      • Response
      P66-6 (CODE) - P66-11 (AGND) Y - L Input Signal input from transponder key amplifier Power switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
      P66-7 (VC5) - P66-11 (AGND) P - L Output Transponder key amplifier power supply Power switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
      P66-11 (AGND) - Body ground L - Body ground - Transponder key amplifier ground Always Below 1 Ω
      P66-5 (TXCT) - P66-11 (AGND) W - L Output

      Signal output to transponder key amplifier

      (Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into power switch, and then transmitted by transponder key amplifier antenna as radio waves)

      		 Power switch off, key not in cabin, within 30 seconds after power switch pressed

      Pulse generation

      (See waveform 4)

      Entry&Start


      • BCC Malfunction

      • Abnormal Status

      • Different Encrypt Code

      • Different Serial Number

      • Frame Error

      • Response

      Tech Tips

      If immobiliser key code verification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above
      P66-6 (CODE) - P66-11 (AGND) Y - L Input

      Signal input from transponder key amplifier

      (Radio waves from transponder key amplifier built into power switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))

      		 Power switch off, power switch pressed with key held near power switch*

      Pulse generation

      (See waveform 5)
      P66-7 (VC5) - P66-11 (AGND) P - L Output

      Transponder key amplifier power supply

      (Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into power switch activated)

      		 Power switch off, key not in cabin, within 30 seconds after power switch pressed

      Pulse generation

      (See waveform 6)
      P66-20 (IND) - P66-18 (E) R - W-B Output Security indicator output Power switch off → on (IG) Pulse generation → Below 2 V -

      Tech Tips


      • The waveform of the steering lock actuator motor stopped can be checked without performing any particular operation.

      • The waveform of the steering lock actuator motor operating can be checked if either of the following operations is performed:


        • To unlock the steering, bring the electrical key transmitter sub-assembly into the cabin and turn the power switch on (ACC) or on (IG).

        • To lock the steering, open a door with the power switch off and the shift state park (P).

      • *: Remove the transmitter battery before performing this inspection.

    5. Using an oscilloscope, check the waveform of the ECU.

      Note

      The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


      1. B000S1ZC22
        *a Steering lock motor not operating
        *b Steering lock motor operating

        Waveform 1

        Item Content
        Tester Connection P66-25 (SLR+) - P66-18(E)
        Tool Setting 2 V/DIV., 200 ms./DIV.
        Condition

        When a door is opened, the steering lock motor will be operated if all of the following conditions are met:


        • The steering is unlocked.

        • The power switch is off.

        • The shift state park (P).
      2. B000OZ4N12

        Waveform 2

        Item Content
        Tester Connection P66-19 (SPD) - P66-18(E)
        Tool Setting 5 V/DIV., 20 ms./DIV.
        Condition Vehicle being driven at approximately 5 km/h (3 mph)

        Tech Tips

        The wavelength becomes shorter as the vehicle speed increases.

      3. B000OMMC02
        *a For 30 seconds after any door closed
        *b After 30 seconds or more have elapsed since any door closed

        Waveform 3

        Item Content
        Tester Connection

        P66-8 (CLG5) - P66-18 (E)

        P66-9 (CG5B) - P66-18 (E)

        X23-5 (CLG6) - P66-18 (E)

        X23-6 (CG6B) - P66-18 (E)
        Tool Setting 2 V/DIV., 500 ms./DIV.
        Condition

        Procedure:


        1. Power switch off

        2. Electrical key transmitter sub-assembly not inside vehicle

        3. Within 30 seconds of closing any door
      4. B000OAGN19

        Waveform 4

        Item Content
        Tester Connection P66-5 (TXCT) - P66-11 (AGND)
        Tool Setting 2 V/DIV., 20 ms./DIV.
        Condition Power switch off, key not in cabin, within 30 seconds after power switch pressed
      5. B000S1CC01
        *a Waveform
        *b Waveform (detail)

        Waveform 5

        Item Content
        Tester Connection P66-6 (CODE) - P66-11 (AGND)
        Tool Setting

        • Waveform:

          2 V/DIV., 20 ms./DIV.

        • Waveform (detail):

          2 V/DIV., 100 μs./DIV.
        Condition Power switch off, power switch pressed with key held near power switch*

        Tech Tips

        *: Remove the transmitter battery before performing this inspection.

      6. B000RSTN06

        Waveform 6

        Item Content
        Tester Connection P66-7 (VC5) - P66-11 (AGND)
        Tool Setting 2 V/DIV., 200 ms./DIV.
        Condition Power switch off, key not in cabin, within 30 seconds after power switch pressed
      7. B000RPJE03

        Waveform 7

        Item Content
        Tester Connection P66-22 (P) - P66-18 (E)
        Tool Setting 10 V/DIV., 10 ms./DIV.
        Condition

        Procedure:


        1. Power switch on (IG)

        2. Shift state park (P)

        Tech Tips

        The waveform will vary depending on the shift state.

  2. CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

    B000TFEC20

    1. Disconnect the P14 steering lock ECU (steering lock actuator or upper bracket assembly) connector.

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Tech Tips

      Measure the values on the wire harness side with the connector disconnected.

      Tester Connection Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
      P14-1 (GND) - Body ground W-B - Body ground - Ground Always Below 1 Ω -
      P14-6 (IG2) - P14-1 (GND) R - W-B Input Power source mode signal Power switch off → power switch on (IG) Below 1 V → 11 to 14 V -
      P14-7 (B) - Body ground V - Body ground Input Power source Power switch off 11 to 14 V -

    3. Reconnect the P14 steering lock ECU (steering lock actuator or upper bracket assembly) connector.

    4. Measure the voltage and puless according to the value(s) in the table below.

      Tester Connection Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
      P14-4 (SLP1) - P14-1 (GND) W - W-B Output Steering lock bar position signal (output signal from steering unlock sensor) Steering locked → unlocked 11 to 14 V → Below 1.5 V

      Entry&Start


      • Sensor Value
      P14-5 (LIN) - P14-1 (GND) V - W-B Input/Output LIN communication line Power switch on (IG) Pulse generation

      Entry&Start


      • Steering Lock Start Cond

    5. Check for pulses according to the value(s) in the table below.

      Tester Connection Wiring Color Wiring Color Terminal Description Condition Specified Condition Related Data List Item
      P14-3 (IGE) - P14-1 (GND) G - W-B Input Steering lock motor activation command signal

      Any door opened when conditions below met, and then steering lock motor activated:


      • Shift state park (P)

      • Steering lock unlocked in advance by carrying key and turning power switch on (IG)

      • After above conditions met, power switch turned off

      Pulse generation

      (see waveform 1)

      Entry&Start


      • Power Supply Short

      • Unlock Request Receive

      • Lock Request Receive

      Tech Tips


      • When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

      • In order to take measurements when the lock motor is operating, perform either of the following operations:


        • To unlock the steering, carry the key and turn the power switch on (ACC) or on (IG).

        • To lock the steering, turn the power switch off with the shift state park (P), and then open a door.

    6. Using an oscilloscope, check the waveform of the ECU.

      Note

      The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


      1. B000S1ZC19
        *a Steering Lock Motor not Operating
        *b Steering Lock Motor Operating

        Waveform 1

        Item Content
        Tester Connection P14-3 (IGE) - P14-1 (GND)
        Tool Setting 2 V/DIV., 200 ms./DIV.
        Condition

        Any door opened when conditions below met, and then steering lock motor activated:


        • Shift state park (P)

        • Steering lock unlocked in advance by carrying key and turning power switch on (IG)

        • After above conditions met, power switch turned off

  3. CHECK ID CODE BOX (IMMOBILISER CODE ECU)

    B000OUFE35

    1. Disconnect the P51 ID code box (immobiliser code ECU) connector.

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Tech Tips

      Measure the values on the wire harness side with the connector disconnected.

      Tester Connection Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
      P51-1 (+B) - Body ground GR - Body ground Input Power source Power switch off 11 to 14 V -
      P51-5 (GND) - Body ground BR - Body ground - Ground Always Below 1 Ω

    3. Reconnect the P51 ID code box (immobiliser code ECU) connector.

    4. Measure the voltage and check for pulses according to the value(s) in the table below.

      Tester Connection Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
      P51-3 (EFII) - P51-5 (GND) V - BR Input

      EFI communication input

      (Signal input from hybrid vehicle control ECU assembly to ID code box (immobiliser code ECU))

      		 Power switch off 11 to 14 V

      Entry&Start


      • EFI Code Receive

      • Engine Start Request
      P51-3 (EFII) - P51-5 (GND) V - BR Input

      EFI communication input

      (Signal input from hybrid vehicle control ECU assembly to ID code box (immobiliser code ECU))

      		 Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery

      Pulse generation

      (See waveform 1)
      P51-4 (EFIO) - P51-5 (GND) LG - BR Output

      EFI communication output

      (Signal output from ID code box (immobiliser code ECU) to hybrid vehicle control ECU assembly)

      		 Power switch off Below 1 V
      P51-4 (EFIO) - P51-5 (GND) LG - BR Output

      EFI communication output

      (Signal output from ID code box (immobiliser code ECU) to hybrid vehicle control ECU assembly)

      		 Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery

      Pulse generation

      (See waveform 2)
      P51-2 (LIN1) - P51-5 (GND) L - BR Input/Output LIN communication line Power switch on (IG) Pulse generation

      Entry&Start


      • Steering Lock Start Cond

    5. Using an oscilloscope, check the waveform of the ECU.

      Note

      The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


      1. Waveform 1

        B000SCVC03
        *a Approximately 160 ms *b Approximately 270 ms
        Item Content
        Tester Connection P51-3 (EFII) - P51-5 (GND)
        Tool Setting 2 V/DIV., 500 ms./DIV.
        Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery

      2. Waveform 2

        B000Q2AC02
        *a Approximately 160 ms *b Approximately 270 ms
        Item Content
        Tester Connection P51-4 (EFIO) - P51-5 (GND)
        Tool Setting 2 V/DIV., 500 ms./DIV.
        Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery

  4. CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY

    B000OQ5E17

    1. Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

      Tester Connection Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
      A22-2 (IG2) - P64-6 (E1) B - W-B Input Power source Power switch on (IG) 11 to 14 V -
      P64-6 (E1) - Body ground W-B - Body ground - Ground Always Below 1 Ω -
      P64-12 (IMO) - P64-6 (E1) V - W-B Output

      EFI communication output

      (Signal output from hybrid vehicle control ECU assembly to ID code box (immobiliser code ECU))

      		 Power switch off 11 to 14 V

      Entry&Start


      • EFI Code Receive

      • Engine Start Request
      P64-12 (IMO) - P64-6 (E1) V - W-B Output

      EFI communication output

      (Signal output from hybrid vehicle control ECU assembly to ID code box (immobiliser code ECU))

      		 Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery

      Pulse generation

      (See waveform 1)
      P64-11 (IMI) - P64-6 (E1) LG - W-B Input

      EFI communication input

      (Signal input from ID code box (immobiliser code ECU) to hybrid vehicle control ECU assembly)

      		 Power switch off Below 1 V
      P64-11 (IMI) - P64-6 (E1) LG - W-B Input

      EFI communication input

      (Signal input from ID code box (immobiliser code ECU) to hybrid vehicle control ECU assembly)

      		 Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery

      Pulse generation

      (See waveform 2)

    2. Using an oscilloscope, check the waveform of the ECU.

      Note

      The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


      1. Waveform 1

        B000SCVC03
        *a Approximately 160 ms *b Approximately 270 ms
        Item Content
        Tester Connection P64-12 (IMO) - P64-6 (E1)
        Tool Setting 2 V/DIV., 500 ms./DIV.
        Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery

      2. Waveform 2 (Reference)

        B000Q2AC02
        *a Approximately 160 ms *b Approximately 270 ms
        Item Content
        Tester Connection P64-11 (IMI) - P64-6 (E1)
        Tool Setting 2 V/DIV., 500 ms./DIV.
        Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery

  5. CHECK POWER SWITCH

    B000R7SE35

    1. Measure the voltage and resistance according to the value(s) in the table below.

      Tester Connection Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
      P27-6 (AGND) - Body ground L - Body ground - Transponder key amplifier ground Always Below 1 Ω -
      P27-7 (TXCT) - P27-6 (AGND) W - L Input Immobiliser communication input Power switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed Below 1 V -
      P27-8 (CODE) - P27-6 (AGND) Y - L Output Immobiliser communication output Power switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed Below 1 V -
      P27-10 (VC5) - P27-6 (AGND) P - L Input Transponder key amplifier power supply Power switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed Below 1 V -

    2. Check for pulses according to the value(s) in the table below.

      Tester Connection Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
      P27-7 (TXCT) - P27-6 (AGND) W - L Input

      Signal input from certification ECU (smart key ECU assembly)

      (Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into power switch, and then transmitted by transponder key amplifier antenna as radio waves)

      		 Power switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds after power switch pressed

      Pulse generation

      (See waveform 1)

      Entry&Start


      • BCC Malfunction

      • Abnormal Status

      • Different Encrypt Code

      • Different Serial Number

      • Frame Error

      • Response

      Tech Tips

      If immobiliser key code verification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above
      P27-8 (CODE) - P27-6 (AGND) Y - L Output

      Signal output to certification ECU (smart key ECU assembly)

      (Radio waves from transponder key amplifier built into power switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))

      		 Power switch off, power switch pressed with electrical key transmitter sub-assembly held near power switch*

      Pulse generation

      (See waveform 2)
      P27-10 (VC5) - P27-6 (AGND) P - L Input

      Transponder key amplifier power supply

      (Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into power switch activated)

      		 Power switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds after power switch pressed

      Pulse generation

      (See waveform 3)

      Tech Tips

      *: Remove the transmitter battery before performing this inspection.

    3. Using an oscilloscope, check the waveform.

      Note

      The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


      1. B000OAGN18

        Waveform 1

        Item Content
        Tester Connection P27-7 (TXCT) - P27-6 (AGND)
        Tool Setting 2 V/DIV., 20 ms./DIV.
        Condition Power switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds after power switch pressed
      2. B000S1CC01
        *a Waveform
        *b Waveform (detail)

        Waveform 2

        Item Content
        Tester Connection P27-8 (CODE) - P27-6 (AGND)
        Tool Setting

        Procedure:


        • Waveform

          1 V/DIV., 20 ms./DIV.

        • Waveform (detail)

          2 V/DIV., 100 μs./DIV.
        Condition Power switch off, power switch pressed with electrical key transmitter sub-assembly held near power switch*

        Tech Tips

        *: Remove the transmitter battery before performing this inspection.

      3. B000RSTN05

        Waveform 3

        Item Content
        Tester Connection P27-10 (VC5) - P27-6 (AGND)
        Tool Setting 2 V/DIV., 200 ms./DIV.
        Condition Power switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds after power switch pressed