REAR AXLE HUB INSTALLATION

CAUTION / NOTICE / HINT

Note


  • When using a vise, place aluminum plates between the part and vise.

  • When using a vise, do not overtighten it.

Tech Tips


  • The following procedure is for the LH side.

  • Other than areas where instructions are provided, use the same procedure for the LH and RH sides.

PROCEDURE


  1. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH


    1. Install the parking brake anchor block sub-assembly, cable support bracket and parking brake plate from the rear axle carrier with the 2 nuts.

      Torque:
      75.5 N*m  { 770 kgf*cm, 56 ft.*lbf }

    2. Install the parking brake plate LH and the rear axle hub and bearing assembly LH to the rear axle carrier LH with the 4 bolts.

      Torque:
      97 N*m  { 989 kgf*cm, 72 ft.*lbf }

  2. INSTALL REAR NO. 1 WHEEL BEARING DUST DEFLECTOR LH


    1. B004A2YC01
      *1 No. 1 Rear Wheel Bearing Dust Deflector LH
      *a Align
      *b No. 1 Rear Wheel Bearing Dust Deflector LH End Face
      *c Rear Axle Hub Bearing Outer Race End Face

      Using SST and a press, press a new No. 1 rear wheel bearing dust deflector LH into the rear axle carrier while checking the sensor installation hole position.

      SST
      09950-70010   ( 09951-07150 )
      09951-01000
      Standard Length
      23.3 to 23.9 mm (0.918 to 0.940 in.)

      Note

      Align the installation hole of the No. 1 rear wheel bearing dust deflector LH with the installation hole of the speed sensor on the rear axle carrier.

  3. INSTALL REAR AXLE ASSEMBLY


    1. B004AU7

      Apply TOYOTA body grease W to the entire contact surface between the rear drive shaft assembly and rear axle hub sub-assembly surface or only apply 0.1 to 0.3 g (0.00353 to 0.0105 oz.) of TOYOTA body grease W to the 4 areas on the axle hub bearing shown in the illustration.

    2. B004C7XC01
      *a Matchmark

      Align the rear axle assembly with the matchmark and install it to the rear drive shaft assembly.

  4. TEMPORARILY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH


    1. B004C6O

      Temporarily tighten the washer and rear shock absorber assembly LH (lower side) with a new nut.

  5. CONNECT REAR NO. 1 SUSPENSION ARM ASSEMBLY LH


    1. B004AVZC01
      *a Torque Wrench Fulcrum Length

      Using ball joint lock nut wrench, fully tighten nut.

      Torque:
      Specified tightening torque
      160 N*m  { 1632 kgf*cm, 118 ft.*lbf }

      Tech Tips


      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Click here

      • When using a ball joint lock nut wrench (fulcrum length of 150 mm (5.906 in.)) + torque wrench (fulcrum length of 600 mm (23.622 in.)): 128 N*m (1305 kgf*cm, 94 ft.*lbf)

  6. CONNECT REAR UPPER CONTROL ARM ASSEMBLY LH


    1. B004ABD

      Fully tighten a new nut.

      Torque:
      160 N*m  { 1632 kgf*cm, 118 ft.*lbf }

  7. CONNECT TOE CONTROL LINK SUB-ASSEMBLY LH (w/o Dynamic Rear Steering)


    1. B004BMM

      Connect the toe control link sub-assembly LH with a new nut.

      Torque:
      118 N*m  { 1203 kgf*cm, 87 ft.*lbf }

  8. CONNECT REAR STEERING TIE ROD ASSEMBLY LH (w/ Dynamic Rear Steering)

    Click here

  9. TEMPORARILY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH


    1. B004CPK

      Insert the bolt from the front of the vehicle. Then temporarily tighten the rear No. 2 suspension arm assembly LH with the nut and washer.

  10. TEMPORARILY TIGHTEN LOWER CONTROL ARM ASSEMBLY LH


    1. B004AZS

      Temporarily tighten the lower control arm assembly LH with a new nut.

  11. TEMPORARILY TIGHTEN REAR STABILIZER LINK ASSEMBLY LH

    Click here

  12. INSTALL PARKING BRAKE

    Click here

  13. TEMPORARILY TIGHTEN REAR AXLE SHAFT NUT LH


    1. Using a 32 mm socket wrench, while applying the brakes, temporarily install the rear axle shaft nut.

      Torque:
      290 N*m  { 2957 kgf*cm, 214 ft.*lbf }

      Note

      Stake the rear axle shaft nut after inspecting for looseness and runout in the following steps.

      Tech Tips

      Keep depressing the brake pedal to prevent the rear drive shaft assembly from rotating.

  14. INSPECT REAR AXLE HUB BEARING LOOSENESS

    Click here

  15. INSPECT REAR AXLE HUB RUNOUT

    Click here

  16. INSTALL REAR DISC LH

    Click here

  17. ADJUST BRAKE DISC INSIDE DIAMETER

    Click here

  18. INSTALL PARKING BRAKE SHOE SHOE ADJUSTING HOLE PLUG

    Click here

  19. INSTALL REAR SPEED SENSOR LH

    Click here

  20. CONNECT SKID CONTROL SENSOR WIRE


    1. B004B84

      for LH Side:


      1. Install the sensor clamp with the bolt.

        Torque:
        8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      2. Connect the speed sensor connector to the rear speed sensor LH.

    2. B004B8S

      for RH Side:


      1. Install the sensor clamp with the bolt.

        Torque:
        8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      2. Connect the speed sensor connector to the rear speed sensor RH.

      3. Connect the pad wear indicator connector.

  21. CONNECT REAR DISC BRAKE CYLINDER ASSEMBLY


    1. Install the rear disc brake cylinder assembly LH to the steering knuckle with the 2 bolts.

      Torque:
      151 N*m  { 1540 kgf*cm, 111 ft.*lbf }

      Note


      • Do not twist the flexible hose.

      • Make sure that the threaded portion is free from damage and foreign matter.

      • Do not overtighten the bolts, as the threaded portion is part of the aluminum hub carrier.

    2. for RH side:


      1. Attach the 4 clamps to connect the pad wear indicator assembly to the parking brake plate.

  22. INSTALL REAR AXLE SHAFT NUT LH


    1. B004A1I

      Using a chisel and hammer, stake the rear axle shaft nut LH.

  23. STABILIZE SUSPENSION

    Click here

  24. FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH


    1. B004C6O

      Fully tighten the nut.

      Torque:
      110 N*m  { 1122 kgf*cm, 81 ft.*lbf }

  25. FULLY TIGHTEN REAR STABILIZER LINK ASSEMBLY LH

    Click here

  26. CONNECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

    Click here

  27. FULLY TIGHTEN LOWER CONTROL ARM ASSEMBLY LH


    1. Fully tighten the nut.

      Torque:
      118 N*m  { 1203 kgf*cm, 87 ft.*lbf }

  28. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH


    1. B004CPK

      Fully tighten the nut.

      Torque:
      165 N*m  { 1683 kgf*cm, 122 ft.*lbf }

  29. FULLY TIGHTEN TOE CONTROL LINK SUB-ASSEMBLY LH


    1. B004AZS

      Fully tighten the nut (rear axle carrier sub-assembly LH side).

      Torque:
      118 N*m  { 1203 kgf*cm, 87 ft.*lbf }

  30. ADJUST PARKING BRAKE

    Click here

  31. INSTALL REAR WHEEL

    Click here

  32. CONNECT BRAKE BOOSTER PUMP CONNECTOR

    Click here

  33. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

    Click here

  34. CHECK FOR SPEED SENSOR SIGNAL

    Click here

  35. ADJUST HEADLIGHT AIMING

    Click here

  36. ADJUST REAR TELEVISION CAMERA ASSEMBLY OPTICAL AXIS

    Click here

  37. PERFORM DYNAMIC REAR STEERING SYSTEM CALIBRATION (w/ Dynamic Rear Steering)

    Click here