PARKING LOCK RELEASE CABLE INSTALLATION

CAUTION / NOTICE / HINT

Note

The parking shift lock release stopper used to prevent improper installation that is included with the parking lock release lever supply part is removed in the No. 2 parking lock release cable assembly installation procedure.

PROCEDURE


  1. INSTALL NO. 2 PARKING RELEASE CABLE BRACKET SUB-ASSEMBLY

    Tech Tips

    There is no need to remove this unless the No. 2 parking release cable bracket sub-assembly is replaced.


    1. B000S97

      Install the No. 2 parking release cable bracket sub-assembly to the engine rear mounting member with the 2 bolts.

      Torque:
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

  2. INSTALL PARKING LOCK RELEASE LEVER ASSEMBLY


    1. B004ADWC01
      *A for LHD
      *B for RHD
      B004C4F Bolt A
      B004ANI Bolt B

      Pass the parking lock release lever assembly through the floor panel through holes and install it with the 4 bolts.

      Tech Tips


      • Do not damage the cable with the floor panel through holes.

      • Do not bend the cable.

      Torque:
      for bolt A
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }
      for bolt B
      14.5 N*m  { 148 kgf*cm, 11 ft.*lbf }
    2. B004BQPC02
      *a Protector
      *b Clamp

      Install the No. 1 parking lock release cable clamp bracket to the parking lock release lever assembly protector.

      Note

      Securely install the protector into the clamp.

    3. B004BMKC01
      *a Stopper

      Install the No. 1 parking lock release cable clamp bracket to the body with the nut.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

      Note

      The rear side of the floor stud bolt is used as a stopper. Therefore, install the nut to the front side.

  3. INSTALL TRANSMISSION CONTROL SHAFT LEVER


    1. B000PMU

      Install the transmission control shaft lever to the No. 2 parking lock release cable assembly with the nut and spring washer.

      Torque:
      12.7 N*m  { 130 kgf*cm, 9 ft.*lbf }

  4. INSTALL NO. 2 PARKING LOCK RELEASE CABLE ASSEMBLY


    1. B004CHUC01
      *a Long Hole

      Install the No. 2 parking lock release cable assembly to the No. 2 parking release cable bracket sub-assembly with the 2 bolts.

      Torque:
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

      Note

      Install so that the long hole is at the bottom side of the vehicle.

    2. B004BWKC01
      *1 Parking Lock Release Lever Assembly Cable End
      *2 No. 2 Parking Lock Release Cable Assembly Cable End

      Connect the parking lock release lever assembly cable end to the No. 2 parking lock release cable assembly cable end.

    3. B004BYTC02
      *1 Cover
      B004B1M Connect

      Attach the 2 claws and connect the cover to the No. 2 parking lock release cable assembly as shown in the illustration.

    4. B004BIRC01
      B004C4F Bolt
      B004ANI Nut and Spring Washer

      Connect the No. 2 parking lock release cable assembly to the shift control actuator assembly with the nut, spring washer and 2 bolts.

      Torque:
      for bolt
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
      for nut
      12.7 N*m  { 130 kgf*cm, 9 ft.*lbf }
    5. B004A8BC01
      *A for LHD
      *B for RHD
      B004B1M Remove

      Remove the parking shift lock release stopper used to prevent improper installation from the parking lock release lever assembly.

      Tech Tips

      The parking shift lock release stopper used to prevent improper installation is only included with supply parts.

  5. INSTALL UPPER NO. 1 CONSOLE SUPPORT BRACKET

    Click here

  6. INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

    Click here

  7. INSTALL NO. 1 CONSOLE BOX SUPPORT

    Click here