HYBRID VEHICLE TRANSMISSION COMPONENTS
ILLUSTRATION
| *A | for LHD | - | - |
| *1 | ENGINE MOTOR CABLE CLAMP BRACKET | *2 | EXHAUST MANIFOLD ASSEMBLY LH |
| *3 | EXHAUST MANIFOLD ASSEMBLY RH | *4 | FLYWHEEL HOUSING SIDE COVER |
| *5 | HYBRID VEHICLE TRANSMISSION ASSEMBLY | *6 | NO. 1 EGR PIPE |
| *7 | NO. 1 EXHAUST PIPE SUPPORT BRACKET SUB-ASSEMBLY | *8 | STARTER HOLE INSULATOR |
| *9 | WIRE HARNESS | *10 | WIRE HARNESS CLAMP BRACKET |
| *11 | GASKET | - | - |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m(kgf*cm, ft.*lbf) |  |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part |  |
Do not apply lubricants |
ILLUSTRATION
| *A | for RHD | - | - |
| *1 | ENGINE MOTOR CABLE CLAMP BRACKET | *2 | EXHAUST MANIFOLD ASSEMBLY LH |
| *3 | EXHAUST MANIFOLD ASSEMBLY RH | *4 | FLYWHEEL HOUSING SIDE COVER |
| *5 | HYBRID VEHICLE TRANSMISSION ASSEMBLY | *6 | NO. 1 EGR PIPE |
| *7 | NO. 1 EXHAUST PIPE SUPPORT BRACKET SUB-ASSEMBLY | *8 | STARTER HOLE INSULATOR |
| *9 | WIRE HARNESS | *10 | WIRE HARNESS CLAMP BRACKET |
| *11 | GASKET | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m(kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | |
Do not apply lubricants |
ILLUSTRATION
| *1 | OIL COOLER WITHOUT HOSE TUBE SUB-ASSEMBLY | *2 | NO. 1 OIL COOLER INLET HOSE |
| *3 | NO. 2 OIL COOLER INLET HOSE | *4 | NO. 1 OIL COOLER OUTLET HOSE |
| *5 | NO. 2 OIL COOLER OUTLET HOSE | *6 | OIL COOLER UNION SUB-ASSEMBLY |
| *7 | GASKET | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m(kgf*cm, ft.*lbf) | ● | Non-reusable part |
ILLUSTRATION
| *A | for LHD | - | - |
| *1 | ENGINE REAR MOUNTING MEMBER | *2 | GENERATOR CABLE |
| *3 | MOTOR CABLE | *4 | REAR ENGINE MOUNTING INSULATOR |
| *5 | TRANSMISSION OIL PUMP INSULATOR | *6 | CONNECTOR COVER |
| *7 | TERMINAL CAP | *8 | NO. 2 WIRING HARNESS CLAMP BRACKET |
| *9 | NO. 3 WIRING HARNESS CLAMP BRACKET | *10 | NO. 2 PARKING LOCK RELEASE CABLE ASSEMBLY |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m(kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | - | - |
ILLUSTRATION
| *A | for RHD | - | - |
| *1 | ENGINE REAR MOUNTING MEMBER | *2 | GENERATOR CABLE |
| *3 | MOTOR CABLE | *4 | REAR ENGINE MOUNTING INSULATOR |
| *5 | TRANSMISSION OIL PUMP INSULATOR | *6 | CONNECTOR COVER |
| *7 | TERMINAL CAP | *8 | NO. 2 WIRING HARNESS CLAMP BRACKET |
| *9 | NO. 3 WIRING HARNESS CLAMP BRACKET | *10 | NO. 2 PARKING LOCK RELEASE CABLE ASSEMBLY |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m(kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | - | - |
ILLUSTRATION
| *1 | AUTOMATIC TRANSMISSION CASE COVER | *2 | DYNAMIC DAMPER |
| *3 | NO. 1 TRANSMISSION BREATHER ASSEMBLY | *4 | NO. 2 TRANSMISSION BREATHER ASSEMBLY |
| *5 | TRANSMISSION OIL PUMP INSULATOR BRACKET | *6 | NO. 2 HEAT INSULATOR BRACKET |
| *7 | WIRING HARNESS CLAMP BRACKET | *8 | NO. 1 WIRING HARNESS CLAMP BRACKET |
| *9 | TRANSMISSION BREATHER HOSE | *10 | O-RING |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Toyota Genuine ATF WS | - | - |