CAMSHAFT INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips

Perform "Inspection After Repairs" after replacing the camshaft, No. 2 camshaft, No. 3 camshaft sub-assembly, No. 4 camshaft sub-assembly, camshaft timing gear assembly or camshaft timing exhaust gear assembly.


PROCEDURE


  1. SET NO. 1 CYLINDER TO TDC/COMPRESSION


    1. B004AAAC01
      *a "0" Timing Mark
      *b Timing Mark (Cutout)

      Turn the crankshaft clockwise to align the timing mark (cutout) on the crankshaft pulley assembly with the "0" timing mark on the timing chain cover assembly.

  2. SET CAMSHAFT TIMING GEAR ASSEMBLY (for Bank 2)

    Tech Tips

    Perform "Inspection After Repairs" after replacing the camshaft timing gear assembly.



    1. B004CU3C01
      *a Timing Mark
      *b Mark Plate (Yellow)

      Align the mark plate (yellow) with the timing mark of the camshaft timing gear assembly as shown in the illustration and install the No. 2 chain sub-assembly to the camshaft timing gear assembly.

    2. B004ABKC01
      *a Place on camshaft timing gear assembly

      Install the chain sub-assembly to the camshaft timing gear assembly, and then set the camshaft timing gear assembly to the camshaft housing LH.

      Tech Tips


      • Place the chain sub-assembly on the camshaft timing gear but do not engage the teeth of the sprocket and the chain sub-assembly.

      • Install the camshaft timing gear so that the timing mark is facing upward.

  3. SET CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY (for Bank 2)

    Tech Tips

    Perform "Inspection After Repairs" after replacing the camshaft timing exhaust gear assembly.



    1. B004CCOC01
      *a Timing Mark
      *b Mark Plate (Yellow)

      Align the mark plate (yellow) with the timing mark of the camshaft timing exhaust gear assembly as shown in the illustration and install the No. 2 chain sub-assembly to the camshaft timing exhaust gear assembly.

    2. Set the camshaft timing exhaust gear assembly to the camshaft housing LH.

  4. SET NO. 3 CHAIN TENSIONER ASSEMBLY


    1. B004C28

      While lifting up the camshaft timing exhaust gear assembly, pass the No. 3 chain tensioner assembly through the No. 2 chain sub-assembly and set it in place.

      Note

      Temporarily set the No. 3 chain tensioner assembly only, do not install the bolt.

  5. INSTALL NO. 3 CAMSHAFT SUB-ASSEMBLY

    Tech Tips

    Perform "Inspection After Repairs" after replacing the No. 3 camshaft sub-assembly.



    1. Clean the camshaft housing LH and camshaft journals and apply engine oil to them.

    2. B004B0LC01
      *1 Valve Stem Cap
      *2 No. 1 Valve Rocker Arm
      *3 Valve Lash Adjuster Assembly
      *a CORRECT
      *b INCORRECT

      Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.

    3. B004C1DC01
      *a Pin Hole
      *b Straight Pin

      Put the camshaft timing gear assembly and camshaft together by aligning the pin hole and straight pin.

    4. Lightly press and turn the camshaft timing gear assembly against the camshaft, and press harder after the pin enters the hole.

      Note

      Securely insert the straight pin of the No. 3 camshaft sub-assembly into the pin hole of the camshaft timing gear assembly.

    5. Check that there is no clearance between the camshaft timing gear assembly flange and No. 3 camshaft sub-assembly.

  6. INSTALL NO. 4 CAMSHAFT SUB-ASSEMBLY

    Tech Tips

    Perform "Inspection After Repairs" after replacing the No. 4 camshaft sub-assembly.



    1. Clean the camshaft housing LH and camshaft journals and apply engine oil to them.

    2. B004B0LC01
      *1 Valve Stem Cap
      *2 No. 1 Valve Rocker Arm
      *3 Valve Lash Adjuster Assembly
      *a CORRECT
      *b INCORRECT

      Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.

    3. B004B6BC01
      *a Pin Hole
      *b Straight Pin

      Put the camshaft timing exhaust gear assembly and No. 4 camshaft together by aligning the pin hole and straight pin.

    4. Lightly press and turn the camshaft timing gear assembly against the camshaft, and press harder after the pin enters the hole.

      Note

      Securely insert the straight pin of the No. 4 camshaft sub-assembly into the pin hole of the camshaft timing exhaust gear assembly.

    5. Check that there is no clearance between the camshaft timing gear assembly flange and No. 4 camshaft sub-assembly.

  7. TEMPORARILY SET CAMSHAFT BEARING CAP (for Bank 2)


    1. Clean the camshaft bearing caps and apply engine oil to them.

    2. B004AKB

      Slide the camshaft timing gear assembly and camshaft timing exhaust gear assembly toward the front of the vehicle.

      Tech Tips

      To ensure there is sufficient space for installing the No. 3 camshaft bearing cap and No. 4 camshaft bearing cap, slide the camshaft timing gear assembly and camshaft timing exhaust gear assembly.

    3. B0049SLC01
      *1 No. 3 Camshaft Bearing Cap
      *2 No. 4 Camshaft Bearing Cap
      *a Replacement Bolt
      *b Replacement Washer

      Remove the replacement bolts and washers (No. 3 camshaft bearing cap and No. 4 camshaft bearing cap side).

      Note

      Do not remove any of the replacement bolts and washers other than those on the No. 3 camshaft bearing cap and No. 4 camshaft bearing cap side.

    4. Temporarily set the No. 3 camshaft bearing cap and No. 4 camshaft bearing cap.

      Note


      • Do not install the bolts of the No. 3 camshaft bearing cap and No. 4 camshaft bearing cap.

      • Do not install any camshaft bearing caps other than the No. 3 camshaft bearing cap and No. 4 camshaft bearing cap.

    5. B004A8O

      Slide the camshaft timing gear assembly and camshaft timing exhaust gear assembly toward the rear of the vehicle.

      Note

      Securely insert the straight pins of the No. 3 camshaft sub-assembly and No. 4 camshaft sub-assembly into the pin holes of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.

  8. TEMPORARILY INSTALL CAMSHAFT TIMING GEAR (for Intake Side of Bank 2)


    1. Check that there is no clearance between the camshaft timing gear assembly flange and No. 3 camshaft sub-assembly.

    2. B004CB2

      Apply engine oil to the areas of the camshaft timing gear bolt shown in the illustration.

    3. B004A7UC01
      *a Hold
      *b Turn

      Use a wrench to hold the hexagonal portion of the No. 3 camshaft sub-assembly.

    4. Temporarily install the camshaft timing gear bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note


      • Installing the camshaft timing gear bolt while there is external force applied to the camshaft timing gear assembly could result in damage to the engine, so make sure that the camshaft bearing cap is not installed when temporarily installing the camshaft timing gear bolt.

      • Be careful not to damage the camshaft housing sub-assembly or spark plug tube with the wrench.

      • Make sure that the flange part of the camshaft timing gear bolt is directly contacting the camshaft timing gear assembly.

  9. TEMPORARILY INSTALL CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 2)


    1. Check that there is no clearance between the camshaft timing exhaust gear assembly flange and No. 4 camshaft sub-assembly.

    2. B004CB2

      Apply engine oil to the areas of the camshaft timing gear bolt shown in the illustration.

    3. B004BU2C01
      *a Hold
      *b Turn

      Use a wrench to hold the hexagonal portion of the No. 4 camshaft sub-assembly.

    4. Temporarily install the camshaft timing gear bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note


      • Installing the camshaft timing gear bolt while there is external force applied to the camshaft timing exhaust gear assembly could result in damage to the engine, so make sure that the camshaft bearing cap is not installed when temporarily installing the camshaft timing gear bolt.

      • Be careful not to damage the camshaft housing sub-assembly or spark plug tube with the wrench.

      • Make sure that the flange part of the camshaft timing gear bolt is directly contacting the camshaft timing exhaust gear assembly.

  10. INSTALL CAMSHAFT BEARING CAP (for Bank 2)


    1. Clean the camshaft bearing caps and apply engine oil to them.

    2. B004A54C02
      *a Replacement Bolts and Washers
      *b Replacement Bolts and Washers Removal
      *c Part Installation
      B004C4F Bolt A
      B004ANI Bolt B

      Check the marks and numbers on the camshaft bearing caps, and then remove the replacement bolts and washers in the order shown in the illustration. Immediately after removing the replacement bolts and washers in the location for a bearing cap, install the bearing cap with the bolts in the order shown in the illustration.

      Torque:
      Bolt A
      28 N*m  { 286 kgf*cm, 21 ft.*lbf }
      Bolt B
      16 N*m  { 163 kgf*cm, 12 ft.*lbf }

      Note


      • Be sure to follow the numerical order when performing this procedure.

      • Do not drop replacement bolts and washers into the cylinder head sub-assembly.

    3. Check the torque of each bolt again.

  11. TIGHTEN CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 2)


    1. B004A7UC01
      *a Hold
      *b Turn

      Use a wrench to hold the hexagonal portion of the No. 3 camshaft sub-assembly.

    2. Tighten the camshaft timing gear bolt.

      Torque:
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }

      Note

      Be careful not to damage the camshaft housing sub-assembly or spark plug tube with the wrench.

  12. TIGHTEN CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 2)


    1. B004BU2C02
      *a Hold
      *b Turn

      Use a wrench to hold the hexagonal portion of the No. 4 camshaft sub-assembly.

    2. Tighten the camshaft timing gear bolt.

      Torque:
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }

      Note

      Be careful not to damage the camshaft housing sub-assembly or spark plug tube with the wrench.

  13. TIGHTEN NO. 3 CHAIN TENSIONER ASSEMBLY


    1. Install the bolt to the No. 3 chain tensioner assembly.

    2. Tighten the bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  14. CONNECT CHAIN SUB-ASSEMBLY (for Bank 2)


    1. B004AGZC01
      *a Paint Mark

      Align the paint marks on the camshaft timing gear assembly and chain sub-assembly and install the chain sub-assembly to the camshaft timing gear assembly.

      Tech Tips

      If the paint marks are not aligned, align them by turning the camshaft slightly.

  15. SET CAMSHAFT TIMING GEAR ASSEMBLY (for Intake Side of Bank 1)

    Tech Tips

    Perform "Inspection After Repairs" after replacing camshaft timing gear assembly.



    1. B004ATNC01
      *a Timing Mark
      *b Mark Plate (Yellow)

      Align the mark plate (yellow) with the timing mark of the camshaft timing gear assembly as shown in the illustration and install the No. 2 chain sub-assembly to the camshaft timing gear assembly.

    2. B004B50C01
      *a Place on camshaft timing gear

      Install the chain to the camshaft timing gear assembly, and then set the camshaft timing gear assembly to the camshaft housing RH.

      Tech Tips


      • Place the chain on the camshaft timing gear assembly but do not engage the teeth of the sprocket and the chain sub-assembly.

      • Install the camshaft timing gear assembly so that the timing mark is facing upward.

  16. SET CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY (for Exhaust Side of Bank 1)

    Tech Tips

    Perform "Inspection After Repairs" after replacing the camshaft exhaust gear assembly.



    1. B004CS7C01
      *a Timing Mark
      *b Mark Plate (Yellow)

      Align the mark plate (yellow) with the timing mark of the camshaft timing exhaust gear assembly as shown in the illustration and install the No. 2 chain sub-assembly to the camshaft timing exhaust gear assembly.

    2. Set the camshaft timing exhaust gear assembly to the camshaft housing RH.

  17. TEMPORARILY SET NO. 2 CHAIN TENSIONER ASSEMBLY


    1. B004CIQ

      While lifting up the camshaft timing exhaust gear assembly, pass the No. 2 chain tensioner assembly through the No. 2 chain sub-assembly and set it in place.

      Note

      Temporarily set the No. 2 chain tensioner assembly only, do not install the bolt.

  18. INSTALL CAMSHAFT

    Tech Tips

    Perform "Inspection After Repairs" after replacing the camshaft.



    1. B0049W1C06
      *a 5° to 10°

      Turn the crankshaft clockwise until it is in the position shown in the illustration so that the chain sub-assembly can be installed easily.

      Tech Tips

      When turning the crankshaft, engine oil may spray out of the oil holes.

    2. Clean the camshaft housing RH and camshaft journals and apply engine oil to them.

    3. B004B0LC01
      *1 Valve Stem Cap
      *2 No. 1 Valve Rocker Arm
      *3 Valve Lash Adjuster Assembly
      *a CORRECT
      *b INCORRECT

      Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.

    4. B004A5IC01
      *a Pin Hole
      *b Straight Pin

      Put the camshaft timing gear assembly and camshaft together by aligning the pin hole and straight pin.

    5. Lightly press and turn the camshaft timing gear assembly against the camshaft, and press harder after the pin enters the hole.

      Note

      Securely insert the straight pin of the camshaft into the pin hole of the camshaft timing gear assembly.

    6. Check that there is no clearance between the camshaft timing gear assembly flange and camshaft.

  19. INSTALL NO.2 CAMSHAFT

    Tech Tips

    Perform "Inspection After Repairs" after replacing the No. 2 camshaft.



    1. Clean the camshaft housing RH and camshaft journals and apply engine oil to them.

    2. B004B0LC01
      *1 Valve Stem Cap
      *2 No. 1 Valve Rocker Arm
      *3 Valve Lash Adjuster Assembly
      *a CORRECT
      *b INCORRECT

      Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.

    3. B004AR7C01
      *a Pin Hole
      *b Straight Pin

      Put the camshaft timing exhaust gear assembly and No. 2 camshaft together by aligning the pin hole and straight pin.

    4. Lightly press and turn the camshaft timing gear assembly against the camshaft, and press harder after the pin enters the hole.

      Note

      Securely insert the straight pin of the No. 2 camshaft sub-assembly into the pin hole of the camshaft timing exhaust gear assembly.

    5. Check that there is no clearance between the camshaft timing gear assembly flange and No. 2 camshaft.

  20. TEMPORARILY SET CAMSHAFT BEARING CAP (for Bank 1)


    1. Clean the camshaft bearing caps and apply engine oil to them.

    2. B004BI0

      Slide the camshaft timing gear assembly and camshaft timing exhaust gear assembly toward the front of the vehicle.

      Tech Tips

      To ensure there is sufficient space for installing the No. 1 camshaft bearing cap and No. 2 camshaft bearing cap, slide the camshaft timing gear assembly and camshaft timing exhaust gear assembly.

    3. B004AJ5C01
      *1 No. 1 Camshaft Bearing Cap
      *2 No. 2 Camshaft Bearing Cap
      *a Replacement Bolt
      *b Replacement Washer

      Remove the replacement bolts and washers (No. 1 camshaft bearing and No. 2 camshaft bearing cap side).

      Note

      Do not remove any of the replacement bolts and washers other than those on the No. 1 camshaft bearing cap and No. 2 camshaft bearing cap side.

    4. Temporarily set the No. 1 camshaft bearing cap and No. 2 camshaft bearing cap.

      Note


      • Do not install the bolts of the No. 1 camshaft bearing cap and No. 2 camshaft bearing cap.

      • Do not install any camshaft bearing caps other than the No. 1 camshaft bearing cap and No. 2 camshaft bearing cap.

    5. B004BWU

      Slide the camshaft timing gear assembly and camshaft timing exhaust gear assembly toward the rear of the vehicle.

      Note

      Securely insert the straight pins of the No. 1 camshaft sub-assembly and No. 2 camshaft sub-assembly into the pin holes of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.

  21. TEMPORARILY INSTALL CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 1)


    1. Check that there is no clearance between the camshaft timing gear assembly flange and camshaft.

    2. B004CB2

      Apply engine oil to the areas of the camshaft timing gear bolt shown in the illustration.

    3. B0049V3C01
      *a Hold
      *b Turn

      Use a wrench to hold the hexagonal portion of the camshaft.

    4. Temporarily install the camshaft timing gear bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note


      • Installing the camshaft timing gear bolt while there is external force applied to the camshaft timing gear assembly could result in damage to the engine, so make sure that the camshaft bearing cap is not installed when temporarily installing the camshaft timing gear bolt.

      • Be careful not to damage the camshaft housing sub-assembly or spark plug tube with the wrench.

      • Make sure that the flange part of the camshaft timing gear bolt is directly contacting the camshaft timing gear assembly.

  22. TEMPORARILY INSTALL CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 1)


    1. Check that there is no clearance between the camshaft timing gear assembly flange and No. 2 camshaft.

    2. B004CB2

      Apply engine oil to the areas of the camshaft timing gear bolt shown in the illustration.

    3. B004CPWC01
      *a Hold
      *b Turn

      Use a wrench to hold the hexagonal portion of the No. 2 camshaft.

    4. Temporarily install the camshaft timing gear bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note


      • Installing the camshaft timing gear bolt while there is external force applied to the camshaft timing exhaust gear assembly could result in damage to the engine, so make sure that the camshaft bearing cap is not installed when temporarily installing the camshaft timing gear bolt.

      • Be careful not to damage the camshaft housing sub-assembly or spark plug tube with the wrench.

      • Make sure that the flange part of the camshaft timing gear bolt is directly contacting the camshaft timing exhaust gear assembly.

  23. INSTALL CAMSHAFT BEARING CAP (for Bank 1)


    1. Clean the camshaft bearing caps and apply engine oil to them.

    2. B004C3MC02
      *a Replacement Bolts and Washers
      *b Replacement Bolts and Washers Removal
      *c Part Installation
      B004C4F Bolt A
      B004ANI Bolt B

      Check the marks and numbers on the camshaft bearing caps, and then remove the replacement bolts and washers in the order shown in the illustration. Immediately after removing the replacement bolts and washers in the location for a bearing cap, install the bearing cap with the bolts in the order shown in the illustration.

      Torque:
      Bolt A
      28 N*m  { 286 kgf*cm, 21 ft.*lbf }
      Bolt B
      16 N*m  { 163 kgf*cm, 12 ft.*lbf }

      Note


      • Be sure to follow the numerical order when performing this procedure.

      • Do not drop replacement bolts and washers into the cylinder head sub-assembly.

    3. Check the torque of each bolt again.

  24. TIGHTEN CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 1)


    1. B0049V3C02
      *a Hold
      *b Turn

      Use a wrench to hold the hexagonal portion of the camshaft.

    2. Tighten the camshaft timing gear bolt.

      Torque:
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }

      Note

      Be careful not to damage the camshaft housing sub-assembly or spark plug tube with the wrench.

  25. TIGHTEN CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 1)


    1. B004CPWC01
      *a Hold
      *b Turn

      Use a wrench to hold the hexagonal portion of the No. 2 camshaft.

    2. Tighten the camshaft timing gear bolt.

      Torque:
      95 N*m  { 969 kgf*cm, 70 ft.*lbf }

      Note

      Be careful not to damage the camshaft housing sub-assembly or spark plug tube with the wrench.

  26. TIGHTEN NO. 2 CHAIN TENSIONER ASSEMBLY


    1. Install the No. 2 chain tensioner assembly with the bolt.

    2. Tighten the bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  27. CONNECT CHAIN SUB-ASSEMBLY (for Bank 1)


    1. B004ATSC01
      *a Paint Mark

      Align the paint marks on the camshaft timing gear assembly and chain sub-assembly and install the chain sub-assembly to the camshaft timing gear assembly.

      Tech Tips

      If the paint marks are not aligned, align them by turning the camshaft slightly.

  28. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY


    1. B004A7XN01

      Turn the crankshaft counterclockwise 30° past the "0" timing mark, and then turn it clockwise to align the notch with the "0" timing mark.

    2. Turn the crankshaft slightly to eliminate the slack in the chain sub-assembly.

      Tech Tips

      Make sure there is some slack in the chain around the area where the No. 1 chain tensioner assembly is installed.

    3. B004BEHC03
      *a Stopper Plate
      *b Plunger
      *c Pin

      While turning the stopper plate of the tensioner clockwise, push in the plunger of the No. 1 chain tensioner assembly as shown in the illustration.

    4. While turning the stopper plate of the No. 1 chain tensioner assembly counterclockwise, insert a pin of 1.27 mm (0.0500 in.) into the holes in the stopper plate and No. 1 chain tensioner assembly to fix the stopper plate in place.

    5. Install the No. 1 chain tensioner assembly with the 2 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    6. Remove the pin from the No. 1 chain tensioner assembly.

  29. INSPECT VALVE TIMING


    1. Check the camshaft timing marks.

      Note


      • Check each timing mark from a viewpoint directly in line with the center of the camshaft and the timing mark on each camshaft timing gear assembly.

      • If the timing marks are checked from any other viewpoint, the valve timing may appear misaligned.

    2. Check that each camshaft timing mark is positioned as shown in the illustration.

      B004AV3C01
      *a Timing Mark *b Viewpoint

      Tech Tips

      for Intake Camshaft:

      Be sure to check mark A at the point when marks B, C and D are positioned in line. If the marks are checked from any other viewpoint, they cannot be checked correctly.

      B004BOYN02

    3. If the valve timing is misaligned, reinstall the timing chain sub-assembly.

    4. Turn the crankshaft 2 revolutions, set the No. 1 cylinder to TDC/compression and check the timing marks again.

  30. INSTALL TIMING CHAIN COVER PLATE


    1. Install a new gasket and the timing chain cover plate with the 4 bolts.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

  31. INSTALL SPARK PLUG TUBE GASKET

    Click here

  32. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

    Click here

  33. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

    Click here

  34. INSTALL NO. 1 FUEL TUBE SUB-ASSEMBLY

    Click here

  35. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

    Click here

  36. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 1)

    Click here

  37. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 1)

    Click here

  38. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2)

    Click here

  39. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 2)

    Click here

  40. INSTALL NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

    Click here

  41. INSTALL SPARK PLUG

    Click here

  42. INSTALL IGNITION COIL ASSEMBLY

    Click here

  43. CONNECT NO. 3 ENGINE WIRE

    Click here

  44. CONNECT WIRE HARNESS

    Click here

  45. INSTALL OIL COOLER OUTLET HOSE BRACKET

    Click here

  46. INSTALL NO. 3 RADIATOR HOSE

    Click here

  47. INSTALL NO. 1 RADIATOR HOSE

    Click here

  48. INSTALL FUEL PUMP ASSEMBLY (for High Pressure)

    Click here

  49. INSTALL INTAKE AIR SURGE TANK ASSEMBLY

    Click here

  50. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL


    1. Connect the cable to the negative auxiliary battery terminal.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

  51. INSTALL NO. 2 DECK BOARD

  52. ADD ENGINE COOLANT

    Click here

  53. INSPECT FOR COOLANT LEAK

    Click here

  54. INSPECT IGNITION TIMING

    Click here