SFI SYSTEM(w/o Canister Pump Module), Diagnostic DTC:P062F44

DTC Code DTC Name
P062F44 Internal Control Module EEPROM Data Memory Failure

DESCRIPTION

The ECM monitors its internal operation and stores this DTC when it detects an internal malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P062F44 Internal Control Module EEPROM Data Memory Failure An ECM internal error (EEPROM) (1 trip detection logic). ECM Comes on DTC stored SAE: P062F

MONITOR DESCRIPTION

The ECM monitors its internal operation. If the internal operation is malfunctioning, the ECM illuminates the MIL and store this DTC.

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the GTS off.

  6. Turn the power switch off.

  7. Disconnect the GTS.

  8. Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.

  9. Connect the cable to the negative (-) auxiliary battery terminal.

  10. Connect the GTS to the DLC3.

  11. Turn the power switch on (IG).

  12. Turn the GTS on.

  13. Put the engine in Inspection Mode (2WD for measuring Exhaust Gas).

    Click here

  14. Start the engine and wait 30 seconds or more.

  15. Enter the following menus: Powertrain / Engine / Trouble Codes.

  16. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  17. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  18. Input the DTC: P062F44.

  19. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system is malfunctioning.

CAUTION / NOTICE / HINT

Note


  • There is a possibility that the DTC P062F44 is issued from the ECUs of the ECM and hybrid vehicle control ECU.

    Use GTS to conduct a health check to confirm which ECU the DTC is issued from and then inspect the related system.

  • Vehicle Control History may be stored in the hybrid vehicle control ECU if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

    Click here

    (Select Powertrain in Health Check and then check the time stamp data.)

    Click here

  • If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

    Click here

  • After turning power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine > Clear DTCs

    5. Turn the power switch off.

      Result
      Proceed to
      NEXT

    NEXT

  2. READ OUTPUT DTC (DTC P062F44)


    1. Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Connect the GTS to the DLC3.

    4. Turn the power switch on (IG).

    5. Turn the GTS on.

    6. Put the engine in Inspection Mode (2WD for measuring Exhaust Gas).


      Powertrain > Hybrid Control > Utility
      Tester Display
      Inspection Mode

    7. Start the engine and wait 30 seconds or more.

    8. Enter the following menus: Powertrain / Engine / Trouble Codes.

    9. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTCs are not output A
      DTC P062F44 is output B

    A

    CHECK FOR INTERMITTENT PROBLEMS Click here

    B

    REPLACE ECM Click here