SFI SYSTEM(w/o Canister Pump Module) FAIL-SAFE CHART

If any of the following DTCs are stored, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily or stops fuel injection.

DTC Code	Component	Fail-Safe Operation	Fail-Safe Deactivation Condition
P001100 P001500 P002100 P002500	VVT system	Idle up (control of combustion decreased).	Pass condition detected
P003012 P003013 P005012 P005013 P101A9E P103A9E	Air fuel ratio sensor (sensor 1) heater	The ECM turns off the air fuel ratio sensor (sensor 1) heater.	Power switch off
P003612 P003613 P005612 P005613 P102A9E P105A9E	Air fuel ratio sensor (sensor 2) heater	The ECM turns off the air fuel ratio sensor (sensor 2) heater.	Power switch off
P006900 P222611 P222615	Manifold absolute pressure sensor Atmospheric pressure sensor (ECM)	The ECM maintains the last learned atmospheric pressure value.	Pass condition detected
P008700 P008800	Fuel pump assembly (for high pressure side)	Stop the fuel pump (for high pressure side). Limit the engine speed to 2000 rpm or less.	Pass condition detected
P010012 P010014	Mass air flow meter sub-assembly	The ECM calculates ignition timing according to the engine speed and throttle valve position.	Pass condition detected
P011011 P011015	Intake air temperature sensor	The ECM estimates the intake air temperature to be 20°C (68°F).	Pass condition detected
P011511 P011515	Engine coolant temperature sensor	The ECM estimates the engine coolant temperature to be 80°C (176°F).	Pass condition detected
P012011 P012015 P01201C P022011 P022015 P060444 P060647 P060A47 P060B49 P060E49 P065714 P06579E P210014 P210015 P211900 P211904 P211977 P21352B	Electronic throttle control system	The ECM cuts off throttle actuator current and the throttle valve is returned to a 7° throttle position by the return spring. The ECM controls the fuel injection duration and ignition timing in accordance with the engine torque requested by the hybrid vehicle control ECU. Fuel-cut is performed intermittently.*	Pass condition detected and then power switch turned off
P019011 P019015 P123513	Fuel pressure sensor (for high pressure)	Stop the fuel pump assembly (for high pressure side). Limit the engine speed to 2000 rpm or less. Fuel pressure is set to 200 kPa.	Pass condition detected and then power switch turned off
P020113 P020213 P020313 P020413 P020513 P020613 P062D13	ECM (injector driver)	The ECM performs fuel-cut when the engine speed is 2000 rpm or more. Fuel cut of malfunction cylinder.	Pass condition detected and then power switch turned off
P032511 P032515 P033011 P033015	Knock control sensor	The ECM sets the ignition timing to maximum retard.	Power switch off
P035113 P035213 P035313 P035413 P035513 P035613	Ignition coil assembly	The ECM cuts the fuel injection.	Pass condition detected
P04019C P040314 P140000 P140596 P141004	EGR valve assembly	The ECM fully closes the EGR valve and stops EGR control.	Pass condition detected and then power switch turned off
P107A11 P107A15	Fuel pressure sensor (for low pressure side)	Fuel pump (for low pressure side) control is maintained.	Pass condition detected and then power switch turned off
P211172 P211173	Electronic throttle control system	The ECM stops the engine and the vehicle can be driven using solely the hybrid system.*	Pass condition detected and then power switch turned off
P21CF13 P21D013 P21D113 P21D213 P21D313 P21D413	Fuel injector assembly (for port injection)	The ECM performs fuel-cut when the engine speed is 2000 rpm or more. Fuel cut of malfunction cylinder.	Pass condition detected and then power switch turned off
P223711 P223712 P223714 P223716 P223717 P22371A P224011 P224012 P224014 P224016 P224017 P22401A P225111 P225112 P225411 P225412	Air fuel ratio sensor (sensor 1)	Air fuel ratio feedback control is stopped. Current to the air fuel ratio sensor (sensor 1) heater is cut.	Pass condition detected and then power switch turned off

Tech Tips

*: The vehicle can be driven slowly when the accelerator pedal is depressed firmly and slowly.