SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P222611, P222615

DTC Code DTC Name
P222611 Barometric Pressure Sensor "A" Circuit Short to Ground
P222615 Barometric Pressure Sensor "A" Circuit Short to Battery or Open

DESCRIPTION

The atmospheric pressure sensor is built into the ECM. The ECM provides optimal control in response to atmospheric pressure fluctuations.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P222611 Barometric Pressure Sensor "A" Circuit Short to Ground Short in atmospheric pressure sensor circuit (ECM internal malfunction) (1 trip detection logic). ECM Comes on DTC stored SAE: P2228
P222615 Barometric Pressure Sensor "A" Circuit Short to Battery or Open Open or short in atmospheric pressure sensor circuit (ECM internal malfunction) (1 trip detection logic). ECM Comes on DTC stored SAE: P2229

MONITOR DESCRIPTION

The ECM calculates the atmospheric pressure from the atmospheric pressure sensor output voltage. When the atmospheric sensor assembly output voltage is outside of the normal range, there may be an open or short in the atmospheric pressure sensor circuit or the atmospheric pressure sensor may be malfunctioning. In this case, the ECM will illuminate the MIL and store a DTC.

MONITOR STRATEGY

Required Sensors/Components Atmospheric pressure sensor (ECM)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the power switch off and wait for at least 30 seconds.

  6. Turn the power switch on (IG).

  7. Turn the GTS on.

  8. With power switch on (IG) and wait for 5 seconds or more.

  9. Enter the following menus: Powertrain / Engine / Trouble Codes.

  10. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  12. Input the DTC: P222611 or P222615.

  13. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system is malfunctioning.

CAUTION / NOTICE / HINT

Note


  • Vehicle Control History may be stored in the hybrid vehicle control ECU if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

    Click here

    (Select Powertrain in Health Check and then check the time stamp data.)

    Click here

  • If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

    Click here

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK DTC OUTPUT


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Trouble Codes.

    5. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Proceed to
      NEXT

    NEXT

    REPLACE ECM Click here