NOISE FILTER INSTALLATION

PROCEDURE


  1. INSTALL RADIO SETTING CONDENSER (for Window Defogger)


    1. B004A96

      Attach the claw to install a new terminal cover to the wire harness.

      Note


      • Make sure to hold the crimping side of the terminal when installing the wire harness to the terminal cover.

      • Make sure not to bend the exposed wire when installing the wire harness to the terminal cover.

      • Do not use excessive force when inserting the wire harness into the terminal cover.

      • If the terminal cover has been deformed during installation, replace the terminal and terminal cover with new ones.

    2. B004CCHC02
      B004B1M Install in this Direction

      Attach the claws to install the new terminal cover with wire harness to a new condenser.

      Note


      • Do not use excessive force when inserting the terminal cover into the condenser.

      • If the terminal cover has been deformed during installation, replace the terminal, terminal cover and condenser with new ones.

    3. B004B0Y

      Attach the clamp to temporarily install a new radio setting condenser with wire harness.

    4. Install the radio setting condenser with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  2. INSTALL QUARTER TRIM PANEL ASSEMBLY LH

    Click here

  3. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)

    Click here

  4. INSTALL LAP BELT OUTER ANCHOR COVER

    Click here

  5. INSTALL REAR NO.1 SEAT INNER BELT ASSEMBLY LH

    Click here

  6. INSTALL QUARTER INSIDE TRIM BOARD LH

    Click here

  7. INSTALL FRONT DOOR SCUFF PLATE LH

    Click here

  8. INSTALL RADIO SETTING CONDENSER (for High Mounted Stop Light)


    1. B004CVC

      Attach the claw to install a new terminal cover to the wire harness.

      Note


      • Make sure to hold the crimping side of the terminal when installing the wire harness to the terminal cover.

      • Make sure not to bend the exposed wire when installing the wire harness to the terminal cover.

      • Do not use excessive force when inserting the wire harness into the terminal cover.

      • If the terminal cover has been deformed during installation, replace the terminal and terminal cover with new ones.

    2. B004CGUC02
      B004B1M Install in this Direction

      Attach the claws to install 2 new terminal covers with wire harness to a new condenser.

      Note


      • Do not use excessive force when inserting the terminal covers into the condenser.

      • If a terminal cover has been deformed during installation, replace the terminal, terminal covers and condenser with new ones.

    3. B004CSOC02
      B004B1M Install in this Direction

      Insert the cover as shown in the illustration and engage the claw.

    4. B004C0F

      Attach the clamp to temporarily install the new radio setting condenser with wire harness.

    5. Install the radio setting condenser with the bolt.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

  9. INSTALL REAR SEATBACK ASSEMBLY LH

    Click here

  10. INSTALL REAR SEATBACK COVER

    Click here

  11. INSTALL REAR SEAT SIDE GARNISH

    Click here

  12. INSTALL REAR SEAT CUSHION LOCK HOOK

    Click here

  13. INSTALL REAR SEAT CUSHION ASSEMBLY

    Click here

  14. INSTALL FRONT SEAT ASSEMBLY LH

    Click here

  15. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  16. INSTALL NO. 2 DECK BOARD

    Click here

  17. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  18. CHECK SRS WARNING LIGHT

    Click here