REAR BUMPER REASSEMBLY

PROCEDURE


  1. INSTALL REAR BUMPER REINFORCEMENT SUB-ASSEMBLY (for Reinforcement Type A)


    1. B000XVZC02
      B000WYJ Install in this Direction

      Install the rear bumper reinforcement sub-assembly with the 10 bolts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

  2. INSTALL REAR BUMPER ENERGY ABSORBER (for Reinforcement Type A)


    1. B000Z9VC02
      B000WYJ Install in this Direction

      Attach the guides to install the rear bumper energy absorber.

  3. INSTALL REAR BUMPER REINFORCEMENT SUB-ASSEMBLY (for Reinforcement Type B)


    1. B000WUH

      Install the rear bumper reinforcement sub-assembly with the 10 bolts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

  4. INSTALL REAR BUMPER ENERGY ABSORBER (for Reinforcement Type B)


    1. B000VOW

      Attach the guides and claws to install the rear bumper energy absorber.

  5. INSTALL REAR BUMPER BAR REINFORCEMENT LH (for Reinforcement Type B)


    1. B000ZBN

      Install the rear bumper bar reinforcement LH with the 3 bolts.

      Torque:
      23 N*m  { 235 kgf*cm, 17 ft.*lbf }

  6. INSTALL REAR BUMPER BAR REINFORCEMENT RH (for Reinforcement Type B)

    Tech Tips

    Use the same procedure described for the LH side.

  7. INSTALL REAR BUMPER ARM REINFORCEMENT LH (for Reinforcement Type B)


    1. B000VU9

      Attach the guide.

    2. Install the rear bumper arm reinforcement LH with 2 bolts.

  8. INSTALL REAR BUMPER ARM REINFORCEMENT RH (for Reinforcement Type B)

    Tech Tips

    Use the same procedure described for the LH side.

  9. INSTALL REAR BUMPER NO. 1 SIDE SUPPORT LH


    1. B000Y1RC01
      B000WYJ Install in this Direction

      Attach the guides and install the rear bumper No. 1 side support LH with the 2 screws.

    2. B000YOD

      Install the 2 grommets.

  10. INSTALL REAR BUMPER NO. 1 SIDE SUPPORT RH

    Tech Tips

    Use the same procedure described for the LH side.

  11. INSTALL REAR BUMPER NO. 4 SIDE SUPPORT LH


    1. B000YIUC01
      B000WYJ Install in this Direction

      Temporarily install the rear bumper No. 4 side support LH with the grommet.

    2. B000XIQ

      Install the rear bumper No. 4 side support LH with the 2 clips.

  12. INSTALL REAR BUMPER NO. 4 SIDE SUPPORT RH

    Tech Tips

    Use the same procedure described for the LH side.

  13. INSTALL REAR BUMPER NO. 2 SIDE SUPPORT LH

    B000U5XC01
    B000WYJ Install in this Direction

    1. Attach the claw.

    2. Attach the clips to install the rear bumper No. 2 side support LH.

  14. INSTALL REAR BUMPER NO. 2 SIDE SUPPORT RH

    Tech Tips

    Use the same procedure described for the LH side.

  15. INSTALL REAR BUMPER NO. 2 PAD

    Tech Tips

    When installing the rear bumper No. 2 pad, heat the rear bumper corner extension LH using a heat light.

    Standard
    Item Temperature
    Rear Bumper Corner Extension LH 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear bumper corner extension LH excessively.


    1. When reusing the rear bumper corner extension LH:


      1. Using a heat light, heat the rear bumper corner extension LH installation surface.

      2. Remove the double-sided tape from the rear bumper corner extension LH.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Using a heat light, heat the rear bumper corner extension LH.

    3. Remove the peeling paper from a new rear bumper No. 2 pad.

    4. B000V8FC01
      *a Mark-off Line

      Align the rear bumper No. 2 pad with the mark-off line of the rear bumper corner extension LH.

      Tech Tips


      • Press the rear bumper No. 2 pad firmly to install it.

      • Use the same procedure for the RH side and LH side.

  16. INSTALL REAR BUMPER NO. 3 PAD

    Tech Tips

    When installing the rear bumper No. 3 pad, heat the rear bumper corner extension LH using a heat light.

    Standard
    Item Temperature
    Rear Bumper Corner Extension LH 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear bumper corner extension LH excessively.


    1. When reusing the rear bumper corner extension LH:


      1. Using a heat light, heat the rear bumper corner extension LH installation surface.

      2. Remove the double-sided tape from the rear bumper corner extension LH.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Using a heat light, heat the rear bumper corner extension LH.

    3. Remove the peeling paper from a new rear bumper No. 3 pad.

    4. B000TVSC01
      *a Mark-off Line

      Align the rear bumper No. 3 pad with the mark-off line of the rear bumper corner extension LH.

      Tech Tips


      • Press the rear bumper No. 3 pad firmly to install it.

      • Use the same procedure for the RH side and LH side.

  17. INSTALL REAR BUMPER PAD INSERT

    Tech Tips

    When installing the rear bumper pad insert, heat the rear bumper corner extension LH using a heat light.

    Standard
    Item Temperature
    Rear Bumper Corner Extension LH 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear bumper corner extension LH excessively.


    1. When reusing the rear bumper corner extension LH:


      1. Using a heat light, heat the rear bumper corner extension LH installation surface.

      2. Remove the double-sided tape from the rear bumper corner extension LH.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Using a heat light, heat the rear bumper corner extension LH.

    3. Remove the peeling paper from a new rear bumper pad insert.

    4. B000U6RC01
      *a Mark-off Line

      Align the rear bumper pad insert with the mark-off line of the rear bumper corner extension LH.

      Tech Tips


      • Press the rear bumper pad insert firmly to install it.

      • Use the same procedure for the RH side and LH side.

  18. INSTALL REAR BUMPER CORNER EXTENSION LH

    B000Y5PC01
    B000WYJ Turn Direction

    1. Attach the guides, turn the rear bumper corner extension LH with the guides as a starting point and install the clips.

    2. Attach the claws.

    3. Install the rear bumper corner extension LH with the 3 screws.

  19. INSTALL REAR BUMPER CORNER EXTENSION RH

    Tech Tips

    Use the same procedure described for the LH side.

  20. INSTALL REAR BUMPER EXTENSION


    1. B000X9M

      Attach the claws.

    2. Install the rear bumper extension with the 2 screws.

  21. INSTALL REAR BUMPER EXTENSION LH

    B000U7UC01
    B000WYJ Install in this Direction

    1. Attach the claws to install the rear bumper extension LH.

    2. B000XYT

      Install the 2 screws.

  22. INSTALL REAR BUMPER EXTENSION RH

    Tech Tips

    Use the same procedure described for the LH side.

  23. INSTALL REFLEX REFLECTOR ASSEMBLY LH


    1. B000WBVC01
      B000WYJ Install in this Direction

      Attach the claw.

    2. B000WV1

      Install the reflex reflector assembly LH with the screw.

  24. INSTALL REFLEX REFLECTOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  25. INSTALL REAR BUMPER PAD (w/ Rear Bumper Pad)

    Tech Tips

    When installing the rear bumper pad, heat the rear bumper cover using a heat light.

    Standard
    Item Temperature
    Rear Bumper Cover 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear bumper cover excessively.


    1. When reusing the rear bumper cover:


      1. Using a heat light, heat the rear bumper cover installation surface.

      2. Remove the double-sided tape from the rear bumper cover.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Using a heat light, heat the rear bumper cover.

    3. Remove the peeling paper from a new rear bumper pad.

    4. B000XVGC01
      *a Mark-off Line

      Align the rear bumper pad with the mark-off line of the rear bumper cover.

      Tech Tips


      • Press the rear bumper pad firmly to install it.

      • Use the same procedure for the RH side and LH side.

  26. INSTALL REAR BUMPER NO. 1 PAD

    Tech Tips

    When installing the rear bumper No. 1 pad, heat the rear bumper cover using a heat light.

    Standard
    Item Temperature
    Rear Bumper Cover 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear bumper cover excessively.


    1. When reusing the rear bumper cover:


      1. Using a heat light, heat the rear bumper cover installation surface.

      2. Remove the double-sided tape from the rear bumper cover.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Using a heat light, heat the rear bumper cover.

    3. Remove the peeling paper from a new rear bumper No. 1 pad.

    4. B000WXNC01
      *a Mark-off Line

      Align the rear bumper No. 1 pad with the mark-off line of the rear bumper cover.

      Tech Tips


      • Press the rear bumper No. 1 pad firmly to install it.

      • Use the same procedure for the RH side and LH side.

  27. INSTALL REAR BUMPER CENTER PAD

    Tech Tips

    When installing the rear bumper center pad, heat the rear bumper cover using a heat light.

    Standard
    Item Temperature
    Rear Bumper Cover 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear bumper cover excessively.


    1. When reusing the rear bumper cover:


      1. Using a heat light, heat the rear bumper cover installation surface.

      2. Remove the double-sided tape from the rear bumper cover.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Using a heat light, heat the rear bumper cover.

    3. Remove the peeling paper from a new rear bumper center pad.

    4. B000TS8C01
      *a Mark-off Line

      Align the rear bumper center pad with the mark-off line of the rear bumper cover.

      Tech Tips


      • Press the rear bumper center pad firmly to install it.

      • Use the same procedure for the RH side and LH side.

  28. INSTALL REAR BUMPER CENTER EXTENSION SUB-ASSEMBLY


    1. B000VMZC01
      B000WYJ Install in this Direction

      Attach the guides and claws as shown in the illustration.

    2. B000XIW

      Install the 2 clips.

    3. Install the rear bumper center extension sub-assembly with the 6 screws.

  29. INSTALL REAR BUMPER EXTENSION SUB-ASSEMBLY LH


    1. B000UQSC01
      B000WYJ Install in this Direction

      Temporarily install the rear bumper extension sub-assembly LH with the 4 grommets.

    2. B000V3K

      Install the rear bumper extension sub-assembly LH with the 4 screws.

  30. INSTALL REAR BUMPER EXTENSION SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  31. INSTALL REAR BUMPER PIECE LH


    1. B000Y5KC01
      B000WYJ Install in this Direction

      Install the anti-drop hook.

    2. Attach the claws to install the rear bumper piece LH.

  32. INSTALL REAR BUMPER PIECE RH

    Tech Tips

    Use the same procedure described for the LH side.

  33. INSTALL NO. 1 MOULDING TAPE

    Tech Tips

    When installing the No. 1 moulding tape, heat the rear bumper cover using a heat light.

    Standard
    Item Temperature
    Rear Bumper Cover 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear bumper cover excessively.


    1. When reusing the rear bumper cover:


      1. Using a heat light, heat the rear bumper cover installation surface.

      2. Remove the double-sided tape from the rear bumper cover.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Using a heat light, heat the rear bumper cover.

    3. Remove the peeling paper from a new No. 1 moulding tape.

    4. B000US8C03
      *a Mark-off Line

      Align the No. 1 moulding tape with the mark-off line of the rear bumper cover.

      Tech Tips


      • Press the No. 1 moulding tape firmly to install it.

      • Use the same procedure for the RH side and LH side.

    5. Remove the application tape.

  34. INSTALL LICENSE PLATE LIGHT SUB-ASSEMBLY


    1. B000WVV

      Attach the claws to install the license plate light sub-assembly.

    2. Install the retainer.

  35. INSTALL BACK-UP LIGHT ASSEMBLY

    Click here

  36. INSTALL ULTRASONIC SENSOR CLIP

    Click here

  37. INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System)

    Click here

  38. INSTALL REAR CORNER ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)

    Click here

  39. INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System)

    Tech Tips

    Use the same procedure described for the rear corner ultrasonic sensor retainer.

  40. INSTALL REAR CENTER ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)

    Tech Tips

    Use the same procedure described for the rear center ultrasonic sensor.

  41. INSTALL NO. 3 LUGGAGE ROOM WIRE

    Click here