FRONT BUMPER REASSEMBLY

PROCEDURE


  1. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY


    1. B000XJ7C01
      B000WYJ Install in this Direction

      Install the front bumper reinforcement sub-assembly with the 8 bolts.

      Torque:
      38 N*m  { 387 kgf*cm, 28 ft.*lbf }

  2. INSTALL LOWER ARM BRACKET BRACE SUB-ASSEMBLY LH


    1. B000YXLC01
      B000WYJ Install in this Direction

      Install the lower arm bracket brace sub-assembly LH with the 2 bolts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

  3. INSTALL LOWER ARM BRACKET BRACE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  4. INSTALL HEADLIGHT ASSEMBLY LH

    Click here

  5. INSTALL HEADLIGHT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  6. INSTALL FRONT BUMPER ENERGY ABSORBER

    Click here

  7. INSTALL PEDESTRIAN DETECTION CHAMBER ASSEMBLY

    Click here

  8. INSTALL NO. 2 FRONT BUMPER MOUNTING BRACKET


    1. Check that the engine switch off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      B000Y52
    3. B000YNBC01
      B000WYJ Install in this Direction

      Attach the guides and claws.

    4. B000WT6

      Install the No. 2 front bumper mounting bracket with the 2 bolts.

      Torque:
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }
    5. B000W46

      Connect the 2 connectors of the pedestrian detection chamber assembly.

      Note

      When connecting any pedestrian detection chamber assembly connector, take care not to damage the pedestrian detection chamber assembly wire harness.


      1. Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

        B000XAKC29
        *a Correct *b Incorrect
        *c CPA *d Housing

      2. While holding the CPA be sure to engage the connectors until they are locked and check that the CPA is in its original position (when locking, make sure that a click sound can be heard).

        Tech Tips

        When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and upper part of the CPA, as it may result in an insecure fit.

        B000UWBC31
        *a CPA Upper Part *b Housing Lock
        *c CPA *d Connection is Completed

  9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Click here

  10. INSTALL NO. 2 DECK BOARD

    Click here

  11. INSTALL HEADLIGHT CLEANER HOSE


    1. B000U2T

      Attach the clamps and install the headlight cleaner hose.

    2. B000VPYC02
      B000WYJ Install in this Direction

      Connect the headlight cleaner hose as shown in the illustration.

  12. INSTALL LOWER RADIATOR GRILLE

  13. INSTALL UPPER RADIATOR GRILLE

    B000WJ7C01
    B000WYJ Install in this Direction

    1. Attach the claws.

    2. Install the upper radiator grille with the 2 screws.

  14. INSTALL NO. 2 RADIATOR GRILLE MOULDING


    1. B000Z9JC01
      B000WYJ Install in this Direction

      Attach the claws.

    2. B000UBF

      Install the No. 2 radiator grille moulding with the screw.

  15. INSTALL RADIATOR GRILLE MOULDING


    1. B000WB0C01
      B000WYJ Install in this Direction

      Attach the claws.

    2. B000Y9F

      Install the radiator grille moulding with the 4 screws.

  16. INSTALL RADIATOR GRILLE SUB-ASSEMBLY


    1. Insert the guides and attach the claws.

      B000V8K
    2. B000Y48

      Install the radiator grille assembly with the 8 screws.

  17. INSTALL NO. 2 MOULDING TAPE

    Tech Tips

    When installing the No. 2 moulding tape, heat the front bumper cover.

    Standard
    Item Temperature
    Front Bumper Cover 20 to 30°C (68 to 86°F)

    1. Clean the No. 2 moulding tape installation surface with a non-residue solvent.

    2. Remove the peeling paper on a new No. 2 moulding tape while making sure not to touch the adhesional surface.

    3. B000UZUC01
      *a Mark-off Line

      Install the No. 2 moulding tape in the position shown in the illustration.

      Note

      Press the No. 2 moulding tape firmly to install it.

      Tech Tips

      Use the same procedure for the RH side and LH side.

    4. Remove the application tape.

  18. INSTALL NO. 1 MOULDING TAPE

    Tech Tips

    When installing the No. 1 moulding tape, heat the front bumper cover.

    Standard
    Item Temperature
    Front Bumper Cover 20 to 30°C (68 to 86°F)

    1. Clean the No. 1 moulding tape installation surface with a non-residue solvent.

    2. Remove the peeling paper on a new No. 1 moulding tape while making sure not to touch the adhesional surface.

    3. B000XXRC01
      *a Mark-off Line

      Install the No. 1 moulding tape in the position shown in the illustration.

      Note

      Press the No. 1 moulding tape firmly to install it.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  19. INSTALL NO. 1 FRONT BUMPER SIDE SUPPORT LH

    Tech Tips

    When installing the No. 1 front bumper side support LH, heat the No. 1 front bumper side support LH.

    Standard
    Item Temperature
    No. 1 Front Bumper Side Support LH 20 to 30°C (68 to 86°F)

    1. Clean the No. 1 front bumper side support LH installation surface with a non-residue solvent.

    2. Remove the peeling paper on the No. 1 moulding tape while making sure not to touch the adhesional surface.

    3. B000XNZC02
      *a Mark-off Line
      *b Rib

      Install the No. 1 front bumper side support LH in the position shown in the illustration.

      Note

      Press the No. 1 front bumper side support LH firmly to install it.

      Tech Tips

      Install the No. 1 front bumper side support LH while it is pressed against the rib.

  20. INSTALL NO. 1 FRONT BUMPER SIDE SUPPORT RH

    Tech Tips

    Use the same procedure described for the LH side.

  21. INSTALL FRONT FENDER LINER RETAINER


    1. B000XU6

      Attach the claw to install the 3 front fender liner retainers.

  22. INSTALL FRONT BUMPER HOLE COVER LH


    1. B000XM2C01
      B000WYJ Install in this Direction

      Install the anti-drop hook.

    2. Attach the claws and install the front bumper hole cover LH.

  23. INSTALL NO. 2 WASHER BRACKET

    Click here

  24. INSTALL WASHER BRACKET

    Tech Tips

    Use the same procedure described for the LH side.

  25. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH

    Click here

  26. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  27. INSTALL HEADLIGHT WASHER COVER

    Click here

  28. INSTALL FRONT BUMPER GARNISH LH


    1. B000VTXC01
      *1 Front Bumper Side Retainer
      B000WYJ Install in this Direction
      B000WCG Protective Tape

      Apply protective tape around the front bumper garnish LH.

    2. Attach the clips and claws to install the front bumper side retainer.

    3. Install the front bumper garnish LH with the 2 screws.

    4. Remove the protective tape.

  29. INSTALL FRONT BUMPER GARNISH

    Tech Tips

    Use the same procedure described for the LH side.

  30. INSTALL LOWER SIDE RADIATOR GRILLE LH

    B000VCAC01
    B000WYJ Install in this Direction

    1. Attach the claws to install the lower side radiator grille LH as shown in the illustration.

  31. INSTALL LOWER SIDE RADIATOR GRILLE RH

    Tech Tips

    Use the same procedure described for the LH side.

  32. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY LH

    Click here

  33. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  34. INSTALL ULTRASONIC SENSOR CLIP

    Click here

  35. INSTALL FRONT CENTER ULTRASONIC SENSOR

    Click here

  36. INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER

    Click here

  37. INSTALL FRONT CORNER ULTRASONIC SENSOR

    Click here

  38. INSTALL NO. 4 ENGINE ROOM WIRE

    Click here

  39. INSTALL FRONT BUMPER EXTENTION MOUNTING BRACKET


    1. B000TSU

      for Type A:


      1. Install the front bumper extension mounting bracket with the 2 screws.

    2. B000YE2

      for Type B:


      1. Install the front bumper extension mounting bracket with the 2 screws.

    3. B000VUG

      for Type C:


      1. Install the front bumper extension mounting bracket with the 2 screws.

  40. INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM

    B000TUDC01
    B000WYJ Install in this Direction

    1. Attach the guides and claws.

    2. B000Y7L

      Install the radiator grille (or front panel) emblem with the 2 screws.

  41. INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)

    Click here

  42. INSTALL FRONT BUMPER MOUNTING BRACKET

    B000XKLC01
    B000WYJ Install in this Direction

    1. Install the front bumper mounting bracket with the 2 clips.