LIGHTING SYSTEM, Diagnostic DTC:B242E

DTC Code DTC Name
B242E Open in IG Circuit

DESCRIPTION

The No. 1 headlight ECU sub-assembly operates using the power source voltage input from the IG terminal and ECUB terminal.

The IG terminal power source voltage is supplied by turning the IG1 relay to ON.

The No. 1 headlight ECU sub-assembly receives engine switch on (IG) signals from the main body ECU (multiplex network body ECU) via CAN communication, compares the engine switch on (IG) signal and the power source voltage supply condition of the IG terminal and monitors the result.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B242E Open in IG Circuit

    Detection condition:

  • Engine switch on (IG)


    Malfunction status:

  • When the IG terminal power source voltage is 0 V (engine switch off), IG ON signals from the main body ECU (multiplex network body ECU) via CAN communication are continuously received


    Malfunction duration:

  • 10 seconds or more

  • No. 1 headlight ECU sub-assembly LH

  • No. 1 headlight ECU sub-assembly RH

  • Harness or connector

  • No. 1 headlight ECU sub-assembly LH

  • No. 1 headlight ECU sub-assembly RH

WIRING DIAGRAM

B000UVQE03

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • If the No. 1 headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information.

    Click here

PROCEDURE


  1. CHECK FOR DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > HL AutoLeveling > Clear DTCs
      Body Electrical > HL AutoLeveling (Sub) > Clear DTCs

    2. Turn the engine switch on (IG) and wait for at least 10 seconds.

    3. Check for DTCs.

      Click here


      Body Electrical > HL AutoLeveling > Trouble Codes
      Body Electrical > HL AutoLeveling (Sub) > Trouble Codes
      OK
      DTC B242E is not output.
      Result
      Result Proceed to
      OK A
      NG (DTC output from No. 1 headlight ECU sub-assembly LH) B
      NG (DTC output from No. 1 headlight ECU sub-assembly RH) C

    A

    USE SIMULATION METHOD TO CHECK Click here

    C

    CHECK HARNESS AND CONNECTOR (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH - BATTERY AND BODY GROUND) Click here

    B

  2. CHECK HARNESS AND CONNECTOR (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH - BATTERY AND BODY GROUND)


    1. B000ZCWC79
      *a

      Front view of wire harness connector

      (to No. 1 Headlight ECU Sub-assembly LH)

      Disconnect the No. 1 headlight ECU sub-assembly LH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      A36-4 (IG) - Body ground Engine switch on (IG) 11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A36-12 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  3. CHECK HARNESS AND CONNECTOR (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH - BATTERY AND BODY GROUND)


    1. B000ZCWC80
      *a

      Front view of wire harness connector

      (to No. 1 Headlight ECU Sub-assembly RH)

      Disconnect the No. 1 headlight ECU sub-assembly RH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      A37-4 (IG) - Body ground Engine switch on (IG) 11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A37-12 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR