LIGHTING SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus:


      1. Body Electrical / HL AutoLeveling / Data List.

      2. Body Electrical / HL AutoLeveling (Sub) / Data List.

      3. Body Electrical / Main Body / Data List.

      4. Chassis / Steering Angle Sensor / Data List.

      5. Body Electrical / Power Integration No.1 / Data List.

      6. Body Electrical / Power Integration No.3 / Data List.

      7. Body Electrical / Combination Meter / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > HL AutoLeveling > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Headlight Low Beam State Low beam headlight state OFF or ON

      OFF: Low beam headlights off

      ON: Low beam headlights on

      		 -
      Headlight High Beam State High beam headlight state OFF or ON

      OFF: High beam headlights off

      ON: High beam headlights on

      		 -
      +B No. 1 headlight ECU sub-assembly LH IG power supply voltage value 0 to 19.75 V 11 to 14 V -
      Front Right Wheel Speed Value Front wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 327.67 km/h (203.61 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
      Front Left Wheel Speed Value Front wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 327.67 km/h (203.61 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
      Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph), Max.: 327.67 km/h (203.61 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
      Steering Sensor Signal Steering sensor value -384 to 382.5 deg 0.0 deg (tires straight ahead)

      Turning left: Increases

      Turning right: Decreases
      Steering Sensor Center Position Steering sensor center position -3072 to 3070.5 deg 0.0 deg (tires straight ahead)

      Turning left: Increases

      Turning right: Decreases
      +B Voltage Value No. 1 headlight ECU sub-assembly LH +B power supply voltage value 0 to 19.75 V 11 to 14 V -
      Leveling Motor Target Position Headlight leveling motor target position Min.: 0 %, Max.: 102.3 % 10 to 90 % -
      Steering Sensor Initialization Status Steering sensor initialization status Incomplete or Completed

      Incomplete: Steering sensor initialization not performed

      Completed: Steering angle sensor initialization completed

      		 -
      Clearance Light State Clearance light state OFF or ON

      OFF: Clearance lights off

      ON: Clearance lights on

      		 -
      Right Cornering Light State Cornering light RH state OFF or ON

      OFF: Cornering light RH off

      ON: Cornering light RH on

      		 -
      Left Cornering Light State Cornering light LH state OFF or ON

      OFF: Cornering light LH off

      ON: Cornering light LH on

      		 -
      DRL Operating State Daytime running light state OFF or ON

      OFF: Daytime running lights off

      ON: Daytime running lights on

      		 -
      Front Height Sensor Value Front height sensor value Min.: -128 mm (5.04 in.), Max.: 127 mm (5 in.) Actual front height adjustment normal value is displayed (If there is a malfunction, no value is displayed) -
      Rear Height Sensor Value Rear height sensor value Min.: -128 mm (5.04 in.), Max.: 127 mm (5 in.) Actual front height adjustment normal value is displayed (If there is a malfunction, no value is displayed) -
      VGRS Relative Angle Value Steering sensor value Min.: -3072 deg, Max.: 3070.5 deg 0.0 deg (tires straight ahead)

      Turning left: Increases

      Turning right: Decreases
      Number Of Trouble Codes Number of trouble codes 0 to 255 Number of stored DTCs displayed -

      Body Electrical > HL AutoLeveling (Sub) > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Headlight Low Beam State Low beam headlight state OFF or ON

      OFF: Low beam headlights off

      ON: Low beam headlights on

      		 -
      Headlight High Beam State High beam headlight state OFF or ON

      OFF: High beam headlights off

      ON: High beam headlights on

      		 -
      Clearance Light State Clearance light state OFF or ON

      OFF: Clearance lights off

      ON: Clearance lights on

      		 -
      DRL State(DRL Operating State) Daytime running light state OFF or ON

      OFF: Daytime running lights off

      ON: Daytime running lights on

      		 -
      +B No. 1 headlight ECU sub-assembly RH IG power supply voltage value 0 to 19.75 V 11 to 14 V -
      +B Voltage Value No. 1 headlight ECU sub-assembly RH +B power supply voltage value 0 to 19.75 V 11 to 14 V -
      Number Of Trouble Codes Number of trouble codes 0 to 255 Number of stored DTCs displayed -

      Body Electrical > Main Body > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      ACC SW Engine switch signal OFF or ON

      OFF: Engine switch off

      ON: Engine switch on (ACC)

      		 "ON" is also displayed for this item when the engine switch is on (IG).
      IG SW Engine switch signal OFF or ON

      OFF: Engine switch off

      ON: Engine switch on (IG)

      		 "OFF" is also displayed for this item when the engine switch is on (ACC).
      FR Door Lock Pos Front door RH unlock detection switch signal LOCK or UNLOCK

      LOCK: Front door RH locked

      UNLOCK: Front door RH unlocked

      		 -
      FR Door Courtesy SW Front door courtesy light switch assembly RH signal OFF or ON

      OFF: Front door RH closed

      ON: Front door RH open

      		 -
      FL Door Lock Pos Front door LH unlock detection switch signal LOCK or UNLOCK

      LOCK: Front door LH locked

      UNLOCK: Front door LH unlocked

      		 -
      FL Door Courtesy SW Front door courtesy light switch assembly LH signal OFF or ON

      OFF: Front door LH closed

      ON: Front door LH open

      		 -
      Luggage Courtesy SW Luggage compartment door lock courtesy light switch signal OFF or ON

      OFF: Luggage compartment door closed

      ON: Luggage compartment door open

      		 -
      Head Light SW (Head) Light control switch Head position signal OFF or ON

      OFF: Light control switch not in Head position

      ON: Light control switch in Head position

      		 -
      Insolation Amount of Solar Sensor RH Light control sensor RH condition Min.: 0, Max.: 51100 or SensorFail Condition can be displayed Although the item is displayed on the GTS, it is not applicable to the vehicle.
      Insolation Amount of Solar Sensor LH Light control sensor LH condition Min.: 0, Max.: 51100 or SensorFail Condition can be displayed Although the item is displayed on the GTS, it is not applicable to the vehicle.
      Light Sensor Illuminance Light control sensor illuminance 0 to 8191 lx Value is output according to ambient light level -
      Light Sensor Connection Status Connection status to automatic light control sensor OFF or ON

      OFF: Not Connected

      ON: Connected

      		 -
      Mirr-Foot-Lgt Unlocked/Exterior Light Unlocked Lights up outside handle lights when doors are unlocked using a mechanical key or door control transmitter OFF or ON Customize setting displayed -
      Exterior Light (Door Open) Changes the outside handle light control OFF or ON Customize setting displayed -
      Mirror Foot Light Time/Exterior Light Time Changes the lighting time of the outside handle lights 0 s, 7.5 s, 15 s or 30 s Customize setting displayed -
      Exterior Light Control Changes the outside handle light control OFF or ON Customize setting displayed -
      Headlight Lighting Function ECU which controls the lighting system Main Body or Lighting Sys ECU

      Main Body: Lighting system controlled by main body ECU (multiplex network body ECU)

      Lighting Sys ECU: Lighting system is controlled by No. 1 headlight ECU sub-assembly

      		 -
      Response Time Changes the delay timing of lighting the taillights when going into a tunnel when the light control switch is in the AUTO position Normal or Long Customize setting displayed Vehicles displaying the Item "Response Time" on the GTS
      DRL Function Daytime running light function OFF or ON Customize setting displayed Vehicles displaying the Item "DRL Function" on the GTS.
      Disp Ex ON Sen Ambient brightness level required to dim display lights (combination meter, navigation display, etc.) Normal, Dark2, Dark1, Light1 or Light2 Customize setting displayed -
      Disp Ex OFF Sen Ambient brightness level required to cancel dimming display lights (combination meter, navigation display, etc.) Normal, Dark2, Dark1, Light1 or Light2 Customize setting displayed -
      Suggestion Service Function Suggestion service function OFF, Only Parked or ON Customize setting displayed -
      Light Auto OFF Delay Light auto OFF delay Off, 30 s, 60 s, or 90 s Customize setting displayed Vehicles displaying the Item "Light Auto OFF Delay" on the GTS
      2 Steps Fade Out Control Function Changes the 2 steps fade out control function of the outside handle light control OFF or ON Customize setting displayed -
      Auto H Beam STS0 Automatic high beam sensor state past 0 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed* -
      Auto H Beam STS1 Automatic high beam sensor state past 1 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed* Although the item is displayed on the GTS, it is not applicable to the vehicle.
      Auto H Beam STS2 Automatic high beam sensor state past 2 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed* Although the item is displayed on the GTS, it is not applicable to the vehicle.
      Auto H Beam STS3 Automatic high beam sensor state past 3 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed* Although the item is displayed on the GTS, it is not applicable to the vehicle.
      Auto H Beam STS4 Automatic high beam sensor state past 4 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed* Although the item is displayed on the GTS, it is not applicable to the vehicle.
      Auto H Beam STS5 Automatic high beam sensor state past 5 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed* Although the item is displayed on the GTS, it is not applicable to the vehicle.
      Auto H Beam STS6 Automatic high beam sensor state past 6 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err

      Condition can be displayed*

      Condition can be displayed*

      		 Although the item is displayed on the GTS, it is not applicable to the vehicle.
      Auto H Beam STS7 Automatic high beam sensor state past 7 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed* Although the item is displayed on the GTS, it is not applicable to the vehicle.
      Communication Power Integration No.1 Connection status between No. 1 power integration ECU and main body ECU (multiplex network body ECU) STOP or OK

      STOP: Not Connected

      OK: Connected

      		 -
      Communication Power Integration No.3 Connection status between No. 3 power integration ECU and main body ECU (multiplex network body ECU) STOP or OK

      STOP: Not Connected

      OK: Connected

      		 -
      Follow Me Home Lighting Time Sets the headlight lighting time after the engine switch is turned off 30 s, 60 s, 90 s, or 120 s Customize setting displayed w/ Follow Me Home System
      Light up Clearance Lights at Door Unlock Function Turns on the taillights, clearance light and front side marker lights for 15 seconds when the doors are unlocked by the wireless door unlock or entry door unlock OFF or ON Customize setting displayed -
      The Number of DTC Number of trouble codes 0 to 255 Number of stored DTCs displayed -

      Tech Tips

      *: The details of each value of the Control Range are as follows:

      Range Condition Control Condition Diagnostic Note
      Undetec Automatic high beam sensor being initialized Control suspended (low beam headlights illuminated) -
      CAM NA Automatic high beam sensor temporarily disabled due to high temperature, unclear image (due to dirt, fog, etc.), etc. Control suspended (low beam headlights illuminated) -
      No sens No lights detected High beam headlights illuminated Only when vehicle speed within operation speed range
      Hlight Headlights of oncoming vehicle, etc. detected Low beam headlights illuminated Only when vehicle speed within operation speed range
      Taillgt Taillights preceding vehicle, etc. detected Low beam headlights illuminated Only when vehicle speed within operation speed range
      Speed No lights detected and vehicle speed below operation speed Low beam headlights illuminated -
      Daytime Bright light detected Low beam headlights illuminated -
      Village Streetlights, etc. detected Low beam headlights illuminated Only when vehicle speed within operation speed range
      Delay Changing between low beams and high beams Changing between low beams and high beams Only when vehicle speed within operation speed range
      Malfunc Not applicable - -
      Aim Lmt
      SAE Mod
      Undefin
      LIN Err

      Chassis > Steering Angle Sensor > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Light OFF Switch Light control switch Off position signal OFF or ON

      OFF: Light control switch not in Off position

      ON: Light control switch in Off position

      		 w/ Light Control Switch Off Position
      Auto Light Switch Light control switch Auto position signal OFF or ON

      OFF: Light control switch not in Auto position

      ON: Light control switch in Auto position

      		 -
      Head Light Switch (Tail) Light control switch Tail position signal OFF or ON

      OFF: Light control switch in neither Tail nor Head position

      ON: Light control switch in Tail or Head position

      		 -
      Head Light Switch (Head) Light control switch Head position signal OFF or ON

      OFF: Light control switch not in Head position

      ON: Light control switch in Head position

      		 -
      High Beam Main Switch Headlight dimmer switch High position signal OFF or ON

      OFF: Headlight dimmer switch not in High position

      ON: Headlight dimmer switch in High position

      		 -
      Passing Light Switch Headlight dimmer switch Flash position signal OFF or ON

      OFF: Headlight dimmer switch not in Flash position

      ON: Headlight dimmer switch in Flash position

      		 -
      Auto High Beam Main Switch Automatic high beam main switch signal OFF or ON

      OFF: Automatic high beam main switch off

      ON: Automatic high beam main switch on

      		 -
      Turn Signal Switch (Right) Turn signal switch (right turn position) signal OFF or ON

      OFF: Turn signal switch not in right turn position

      ON: Turn signal switch in right turn position

      		 -
      Turn Signal Switch (Left) Turn signal switch (left turn position) signal OFF or ON

      OFF: Turn signal switch not in left turn position

      ON: Turn signal switch in left turn position

      		 -
      Cornering Light Switch Turn signal switch (right turn position) signal OFF or ON

      OFF: Turn signal switch not in right turn position

      ON: Turn signal switch in right turn position

      		 -
      Front Fog Light Switch Front fog light switch signal OFF or ON

      OFF: Front fog light switch off

      ON: Front fog light switch on

      		 Although the item is displayed on the GTS, it is not applicable to the vehicle.
      Rear Fog Light/Bad Weather Switch Rear fog light switch signal OFF or ON

      OFF: Rear fog light switch off

      ON: Rear fog light switch on

      		 w/ Rear Fog Light
      Automatic Light Equipped Info Automatic light specification information Unknown, With or Without

      Unknown: Specification not stored

      With: Automatic light equipped

      Without: Automatic light not equipped

      		 -
      Bad Weather Mode Equipped Info Bad weather specification information Unknown, With or Without

      Unknown: Specification not stored

      With: Bad weather specification equipped

      Without: Bad weather specification not equipped

      		 Although the item is displayed on the GTS, it is not applicable to the vehicle.
      The Number of DTCs Number of trouble codes 0 to 255 Number of stored DTCs displayed -

      Body Electrical > Power Integration No.1 > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Headlight ECU LH Input Signal No. 1 headlight ECU sub-assembly LH input OFF or ON

      OFF: No. 1 headlight ECU sub-assembly LH is not input

      ON: No. 1 headlight ECU sub-assembly LH is input

      		 -
      Headlight ECU RH Input Signal No. 1 headlight ECU sub-assembly RH input OFF or ON

      OFF: No. 1 headlight ECU sub-assembly RH is not input

      ON: No. 1 headlight ECU sub-assembly RH is input

      		 -
      Headlight ECU LH Output Signal No. 1 headlight ECU sub-assembly LH output OFF or ON

      OFF: No. 1 headlight ECU sub-assembly LH has no power supply

      ON: No. 1 headlight ECU sub-assembly LH has power supply

      		 -
      Headlight ECU RH Output Signal No. 1 headlight ECU sub-assembly RH output OFF or ON

      OFF: No. 1 headlight ECU sub-assembly RH has no power supply

      ON: No. 1 headlight ECU sub-assembly RH has power supply

      		 -
      Headlight ECU LH Output Current No. 1 headlight ECU sub-assembly LH current 0 to 65535 A 8 A or less No. 1 headlight ECU sub-assembly LH current when output is on
      Headlight ECU RH Output Current No. 1 headlight ECU sub-assembly RH current 0 to 65535 A 8 A or less No. 1 headlight ECU sub-assembly RH current when output is on
      Status of Headlight ECU LH Fuse No. 1 headlight ECU sub-assembly LH fuse condition Connect or Disconnect

      Connect: Fuse not shut off

      Disconnect: Fuse shut off

      		 -
      Status of Headlight ECU RH Fuse No. 1 headlight ECU sub-assembly RH fuse condition Connect or Disconnect

      Connect: Fuse not shut off

      Disconnect: Fuse shut off

      		 -
      Headlight ECU LH Fuse Shut Off History No. 1 headlight ECU sub-assembly LH fuse shut off history OFF or ON

      OFF: Fuse has no shut off history

      ON: Fuse has shut off history

      		 -
      Headlight ECU RH Fuse Shut Off History No. 1 headlight ECU sub-assembly RH fuse shut off history OFF or ON

      OFF: Fuse has no shut off history

      ON: Fuse has shut off history

      		 -

      Body Electrical > Power Integration No.3 > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Tail Input Signal Light control switch tail position input signal OFF or ON

      OFF: Light control switch in neither tail nor head position

      ON: Light control switch in tail or head position

      		 -
      Stop Light Input Signal Stop light switch assembly input signal OFF or ON

      OFF: Brake pedal released

      ON: Brake pedal depressed

      		 -
      Emergency Brake Input Signal Emergency brake input signal OFF or ON

      OFF: Emergency brake signal does not operate

      ON: Emergency brake signal operates

      		 Although the item is displayed on the GTS, it is not applicable to the vehicle.
      Rear Fog Light Input Signal Rear fog light switch input signal OFF or ON

      OFF: Rear fog light switch off

      ON: Rear fog light switch on

      		 w/ Rear Fog Light
      Back-up Light Input Signal Back-up light input condition OFF or ON

      OFF: Shift lever in any position other than R

      ON: Shift lever in R

      		 -
      Tail Welcome Light Input Signal Taillight input condition OFF or ON

      OFF: Welcome light is not operating

      ON: Welcome light is operating

      		 -
      Stop Light Output Signal Stop light input condition OFF or ON

      OFF: Stop light is off

      ON: Stop light is on

      		 Stop lights blink during emergency brake signal control
      Rear Fog Light Output Signal Rear fog light output condition OFF or ON

      OFF: Rear fog light not illuminated

      ON: Rear fog light illuminated

      		 w/ Rear Fog Light
      Back-up Light Output Signal Back-up light output condition OFF or ON

      OFF: Back-up light not illuminated

      ON: Back-up light illuminated

      		 -
      Tail Light No.1 Output Signal Taillight output OFF or ON

      OFF: Taillight not illuminated

      ON: Taillight illuminated

      		 Taillights blink while welcome light is operating
      Stop Light Output Current Stop light current 0 to 65535 A 2 A or less Stop light switch assembly current when output is on
      Rear Fog Light Output Current Rear fog light current 0 to 65535 A 2 A or less w/ Rear Fog Light
      Back-up Light Output Current Back-up light current 0 to 65535 A 25 A or less Back-up light current when output is on
      Tail Light No.1 Output Current Taillight current 0 to 65535 A 25 A or less Taillight current when output is on
      Status of Stop Light Fuse Stop light fuse Connect or Disconnect

      Connect: Fuse not shut off

      Disconnect: Fuse shut off

      		 -
      Status of Rear Fog Light Fuse Rear fog light fuse Connect or Disconnect

      Connect: Fuse not shut off

      Disconnect: Fuse shut off

      		 w/ Rear Fog Light
      Status of Back-up Light Fuse Back-up light fuse Connect or Disconnect

      Connect: Fuse not shut off

      Disconnect: Fuse shut off

      		 -
      Status of Tail Light No.1 Fuse Taillight fuse Connect or Disconnect

      Connect: Fuse not shut off

      Disconnect: Fuse shut off

      		 -
      Stop Light Fuse Shut Off History Stop light fuse shut off history OFF or ON

      OFF: Fuse has no shut off history

      ON: Fuse has shut off history

      		 -
      Rear Fog Light Fuse Shut Off History Rear fog light fuse shut off history OFF or ON

      OFF: Fuse has no shut off history

      ON: Fuse has shut off history

      		 w/ Rear Fog Light
      Back-up Light Fuse Shut Off History Back-up light fuse shut off history OFF or ON

      OFF: Fuse has no shut off history

      ON: Fuse has shut off history

      		 -
      Tail Light No.1 Fuse Shut Off History Taillight fuse shut off history OFF or ON

      OFF: Fuse has no shut off history

      ON: Fuse has shut off history

      		 -

      Body Electrical > Combination Meter > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Hazard Flasher Switch Hazard warning signal switch OFF or ON

      OFF: Hazard warning signal switch off

      ON: Hazard warning signal switch on

      		 -

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus:


      1. Body Electrical / HL AutoLeveling / Active Test.

      2. Body Electrical / HL AutoLeveling (Sub) / Active Test.

      3. Body Electrical / Main Body / Active Test.

      4. Body Electrical / Combination Meter / Active Test.

    5. Perform the Active Test according to the display on the GTS.


      Body Electrical > HL AutoLeveling > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Drive The Leveling Motor Headlight leveling motor OFF or ON Perform the Active Test with the engine switch on (IG) and vehicle stopped.
      Headlight Leveling Indicator "Headlight System Malfunction Visit Your Dealer" display OFF or ON -
      Clearance Light Clearance lights OFF or ON -
      Headlight Low Beam Low beam headlights OFF or ON -
      Headlight High Beam High beam headlights OFF or ON Light control switch in Head position.
      Daytime Running Light Daytime running lights OFF or ON -
      Cornering Light Cornering lights OFF or ON -

      Body Electrical > HL AutoLeveling (Sub) > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Clearance Light Clearance lights OFF or ON -
      Headlight Low Beam Low beam headlights OFF or ON -
      Headlight High Beam High beam headlights OFF or ON Light control switch in Head position.
      Daytime Running Light Daytime running lights OFF or ON -
      Cornering Light Cornering lights OFF or ON -

      Body Electrical > Main Body > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Exterior Light Outside handle lights OFF or ON -
      Taillight Relay Taillights and license plate light OFF or ON -
      Headlight Relay Low beam headlights OFF or ON -

      Body Electrical > Combination Meter > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Automatic High Beam Indicator Automatic high beam indicator light OFF or ON w/ Automatic High Beam System