WASHER MOTOR REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the washer jar assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA/LDA system

Click here

Pre-collision system
Parking assist monitor system

Click here

Steering sensor zero point calibration Variable gear ratio steering system

Click here

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    Click here

    B000WAX

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. REMOVE NO. 2 DECK BOARD

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Click here

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative(-) battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    B000Y52

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE FRONT WHEEL LH

    Click here

  5. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

    Click here

  6. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

    Click here

  7. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH


    1. B000VU3

      Remove the 4 screws and front wheel opening extension pad LH.

  8. REMOVE ENGINE SIDE COVER LH


    1. B000UHW

      Remove the 4 clips.

    2. Detach the claw and remove the engine side cover LH.

  9. REMOVE FRONT FENDER LINER LH


    1. B000VN0

      Remove the 4 screws.

    2. B000YJ4C01
      *a 90°

      Using a screwdriver, turn the 3 pin hold clips 90° and remove them.

    3. B000YMW

      Remove the 2 screws and clip.

    4. B000TPC

      Remove the 3 clips.

    5. B000YUA

      Remove the 6 clips.

    6. B000UPK

      Remove the 5 screws.

    7. B000WDEC01
      B000WYJ Remove in this Direction (1)
      B000YNM Remove in this Direction (2)

      Bend the front fender liner LH inward and remove it while sliding the duct towards the bottom of the vehicle as shown in the illustration.

  10. DRAIN WINDSHIELD WASHER FLUID


    1. B000XIX

      Disconnect the washer hose and drain the windshield washer fluid.

      Tech Tips

      Prepare a container before performing the procedure.

  11. REMOVE WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY


    1. B000V0MC01
      B000WYJ Remove in this Direction

      Disconnect the connector.

    2. Disconnect the washer hose.

    3. Pull in the direction of the arrow shown in the illustration and remove the windshield washer motor and pump assembly.

    4. Remove the grommet.

  12. REMOVE FRONT BUMPER COVER

    Click here

  13. REMOVE HEADLIGHT CLEANER HOSE

    Click here

  14. REMOVE NO. 2 FRONT BUMPER MOUNTING BRACKET

    Click here

  15. REMOVE PEDESTRIAN DETECTION CHAMBER ASSEMBLY

    Click here

  16. REMOVE FRONT BUMPER ENERGY ABSORBER

    Click here

  17. REMOVE HEADLIGHT ASSEMBLY LH

    Click here

  18. REMOVE LOWER ARM BRACKET BRACE SUB-ASSEMBLY LH

    Click here

  19. REMOVE LOWER ARM BRACKET BRACE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side

  20. REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY

    Click here

  21. REMOVE WASHER INLET SUB-ASSEMBLY


    1. B000WOX

      Detach the claw and remove the washer inlet sub-assembly.

  22. REMOVE WINDSHIELD WASHER JAR ASSEMBLY


    1. B000VX2C01
      *a Main Nozzle Side
      *b Sub Nozzle Side

      Disconnect the clamp and washer hose at the position shown in the illustration.

    2. B000UJE

      Disconnect the 2 connectors and clamps.

    3. B000Y30

      Remove the 3 bolts, detach the guide and remove the windshield washer jar assembly.

  23. REMOVE LEVEL WARNING SWITCH ASSEMBLY

    Click here

  24. REMOVE HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY

    Click here

  25. REMOVE HEADLIGHT CLEANER CONTROL RELAY

    Click here