INSTRUMENT PANEL SAFETY PAD REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the instrument panel safety pad sub-assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA/LDA system

Click here

Pre-collision system
Parking assist monitor system

Click here

Steering sensor zero point calibration Variable gear ratio steering system

Click here

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

B000WAX

Click here

Tech Tips


  • Use the same procedure as for the LHD and RHD vehicles.

  • The procedure listed below is for the LHD vehicles.

PROCEDURE


  1. TABLE OF BOLT, SCREW AND NUT

    Tech Tips

    All bolts and screws relevant to installing and removing the instrument panel are shown along with their alphabetic code in the table below.

    B000UEWE03

  2. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  3. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  4. CHANGE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS

    Click here

  5. REMOVE NO. 2 DECK BOARD

    Click here

  6. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Click here

    CAUTION:

    B000Y52

    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Click here

    • If the airbag deploys for any reason, it may cause a serious accident.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  7. REMOVE CENTER UPPER INSTRUMENT CLUSTER FINISH PANEL


    1. B000Z60C01
      B000WCN Place hands here
      B000WYJ Remove in this Direction

      Place both hands at the position shown in the illustration and pull towards the rear of the vehicle to detach the clips, claw and guides.

    2. B000W0UC01
      B000WYJ Remove in this Direction

      Lift up the center upper instrument cluster finish panel as shown in the illustration to remove it.

  8. REMOVE METER HOOD SUB-ASSEMBLY


    1. B000UQX

      Disconnect the 2 connectors.

    2. B000USRN01

      Remove the screw <F> or <H> and 2 screws.

    3. B000U8L

      Remove the 2 screws.

    4. B000VGHC01
      B000WCN Place hand here
      B000WYJ Remove in this Direction

      Pull the part in the removal direction shown in the illustration to detach the clips and guides and remove the meter hood.

  9. REMOVE COMBINATION METER ASSEMBLY

    Click here

  10. REMOVE FRONT DOOR SCUFF PLATE LH


    1. B000Z8BC01
      B000WCN Place hand here
      B000WYJ Remove in this Direction

      Place your hand at the position shown in the illustration and open the front door scuff plate LH towards the center of the vehicle. Then, lift it up in the direction of the arrow to detach the claws and guide.

    2. B000V2QC01
      B000WCN Place hands here
      B000WYJ Remove in this Direction
      B000XM7 Order of Removal

      Place both hands in the gap in the vehicle and while pulling in the direction of the arrow shown in the illustration to detach the clips, claws and guide and remove the front door scuff plate LH.

  11. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  12. REMOVE FRONT DOOR OPENING TRIM COVER LH


    1. B000V0XC01
      B000WCN Place hand here
      B000WYJ Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction of the arrow to detach the claws and guide and remove the front door opening trim cover LH.

  13. REMOVE FRONT DOOR OPENING TRIM COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  14. REMOVE FRONT DOOR NO. 2 OPENING TRIM COVER LH


    1. B000TX2C01
      B000WCN Place hand here
      B000WYJ Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claws.

    2. B000VCUC01
      B000WCN Place hand here
      B000WYJ Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction of the arrow to detach the clip and claw and remove the front door No. 2 opening trim cover LH.

  15. REMOVE FRONT DOOR NO. 2 OPENING TRIM COVER RH


    1. B000TRLC01
      B000WCN Place hand here
      B000WYJ Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claws.

    2. B000XTYC01
      B000WCN Place hand here
      B000WYJ Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction of the arrow to detach the clip and claw and remove the front door No. 2 opening trim cover RH.

  16. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. for LHD:


      1. B000X7T

        Remove the 2 screws.

      2. B000WU5C01
        B000WYJ Remove in this Direction

        Detach the claws and lower the No. 1 instrument panel under cover sub-assembly in the direction of the arrow shown in the illustration.

      3. B000WEKC01
        B000WYJ Remove in this Direction

        Detach the claw of the arrow shown in the illustration.

      4. B000YQQ

        Disconnect the connector.

      5. B000VD9C01
        B000WYJ Remove in this Direction

        Pull in the direction of the arrow shown in the illustration to detach the guides and remove the No. 1 instrument panel under cover sub-assembly.

    2. for RHD:


      1. B000XPQ

        Remove the 2 screws.

      2. B000TQEC02
        B000WYJ Remove in this Direction

        Detach the claws and lower the No. 1 instrument panel under cover sub-assembly in the direction of the arrow shown in the illustration.

      3. B000Z17

        Disconnect the connector.

      4. B000Y4IC03
        B000WYJ Remove in this Direction

        Pull in the direction of the arrow shown in the illustration to detach the guides and remove the No. 1 instrument panel under cover sub-assembly.

  17. REMOVE NO. 1 GLOVE COMPARTMENT PANEL


    1. B000W6SC01
      B000WCN Place hand here
      B000WYJ Remove in this Direction
      B000XM7 Order of Removal

      Place your hand at the position shown in the illustration and pull the No. 1 glove compartment panel towards the rear of the vehicle to detach the clips and remove the No. 1 glove compartment panel.

  18. REMOVE CONSOLE BOX ASSEMBLY (for LHD)

    Click here

  19. REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY (for RHD)

    Click here

  20. REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY


    1. B000XGGC01
      B000WCG Protective Tape

      Apply protective tape at the position shown in the illustration.

    2. B000UGC

      Insert moulding remover A at the position shown in the illustration and detach the claw.

    3. B000YKDC02
      B000WCN Place hand here
      B000WYJ Remove in this Direction
      B000XM7 Order of Removal

      Place your hand in the gap and pull diagonally to the upper rear of the vehicle to detach the claws and guides and remove the No. 2 instrument panel garnish sub-assembly.

  21. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. B000YQC

      Detach the claw and guides and remove the hood lock control lever sub-assembly from the No. 1 instrument panel safety pad sub-assembly.

  22. REMOVE NO. 1 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY


    1. B000UKPN01

      Remove the 3 bolts <E>.

    2. B000VSSC01
      B000WCN Place hand here
      B000WYJ Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claws and guide.

    3. B000VM8C01
      B000WCN Place hand here
      B000WYJ Remove in this Direction

      Pull in the direction indicated by the arrow shown in the illustration to detach the clips.

    4. B000Y8L

      Detach the clamp and disconnect the 2 connectors.

    5. B000W6H

      Detach the clamps and disconnect the 2 connectors and remove the No. 1 instrument panel safety pad sub-assembly.

  23. REMOVE INSTRUMENT PANEL REGISTER BEZEL


    1. B000V37C01
      B000WCN Place hand here
      B000WYJ Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claws.

    2. B000YV6C01
      B000WCN Place hand here
      B000WYJ Remove in this Direction

      Pull in the direction of the arrow shown in the illustration to detach the claws and remove the instrument panel register bezel.

  24. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY

    Click here

  25. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET

    Click here

  26. REMOVE ANTENNA DIVIDER (w/ Telematics Transceiver)

    Click here

  27. REMOVE TELEPHONE TRANSCEIVER ASSEMBLY (w/ Telematics Transceiver)

    Click here

  28. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. B000X2LC01
      B000WCG Protective Tape

      Apply protective tape at the position shown in the illustration.

    2. B000UB3C01
      B000WCN Place hand here
      B000WYJ Remove in this Direction

      Pull in the direction of the arrow shown in the illustration to detach the claws.

    3. B000W10

      Pull the No. 2 instrument panel register assembly and disconnect the connector and remove the No. 2 instrument panel assembly.

  29. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. B000VSBC01
      B000WYJ Remove in this Direction

      Detach the claws and lower the No. 2 instrument panel under over sub-assembly in the direction of the arrow shown in the illustration.

    2. B000U81

      Disconnect the connector.

    3. B000Z0EC01
      B000WYJ Remove in this Direction

      Pull in the direction of the arrow shown in the illustration to detach the guides and remove the No. 2 instrument panel under cover.

  30. REMOVE NO. 2 GLOVE COMPARTMENT PANEL


    1. B000W2UC01
      B000WCN Place hand here
      B000WYJ Remove in this Direction

      Place your hand at the position shown in the illustration and pull the No. 2 glove compartment panel towards the outside of the vehicle to detach the claws and remove the No. 2 glove compartment panel.

    2. w/ Airbag Cut Off Switch:

      Disconnect the connector.

  31. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  32. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    1. B000Z5CC01
      B000XM7 Bolt <E>
      B000TT4 Screw <G>

      Detach the clamp.

    2. Remove the 2 bolts <E> and 2 screws <G>.

    3. B000Z3PC01
      B000WCN Place hand here
      B000WYJ Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claws.

    4. B000W9FC01
      *a Clamp
      *b Hook

      Detach the clamps and hook and remove the glove compartment box assembly.

    5. Disconnect the 3 connectors.

  33. REMOVE MULTI-DISPLAY

    Click here

  34. REMOVE FRONT PILLAR GARNISH LH

    Click here

  35. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  36. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. for LHD:


      1. B000V9J

        Disconnect the 2 connectors.

      2. B000WBY

        Detach the claw and remove the connector holder.

    2. B000YH5C01
      B000WCN Place hand here
      B000WYJ Remove in this Direction

      Lift up the part in the removal direction shown in the illustration to detach the claws.

    3. B000YLUC01
      B000WYJ Remove in this Direction

      Pull in the direction of the arrow shown in the illustration to detach the guides and remove the No. 1 instrument panel speaker panel sub-assembly.

  37. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. for RHD:


      1. B000V9J

        Disconnect the 2 connectors.

      2. B000WBY

        Detach the claw and remove the connector holder.

    2. B000V0PC01
      B000WCN Place hand here
      B000WYJ Remove in this Direction

      Lift up the part in the removal direction shown in the illustration to detach the claws.

    3. B000TY2C01
      B000WYJ Remove in this Direction

      Pull in the direction of the arrow shown in the illustration to detach the guides and remove the No. 2 instrument panel speaker panel sub-assembly.

  38. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

    Click here

  39. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  40. REMOVE STEERING WHEEL SWITCH HOUSING

    Click here

  41. REMOVE NO. 2 AIR DUCT


    1. B000WYYC02
      B000WYJ Remove in this Direction

      Remove the 2 bolts and No. 2 air duct in the direction of the arrow shown in the illustration.

  42. REMOVE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY (w/ Double Locking System)

    Click here

  43. REMOVE HEATER TO REGISTER CENTER SUB DUCT


    1. B000VMGN01

      Remove the 2 screws <F> or <H> and heater to register center sub duct.

  44. REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY


    1. for LHD:


      1. B000WWMC03
        *A w/ Clearance Sonar System
        B000XM7 Bolt <A>
        B000TT4 Nut <B>

        Detach the clamps.

      2. Remove the bolt <A>, nut <B> and No. 3 instrument panel to cowl brace sub-assembly.

    2. for RHD:


      1. B000YZ7C05
        *A w/ Clearance Sonar System
        *1 DLC3
        B000XM7 Bolt <A>
        B000TT4 Nut <B>

        Detach the clamps.

      2. Detach the claws and remove the DLC3.

      3. Remove the bolt <A>, nut <B> and No. 3 instrument panel to cowl brace sub-assembly.

  45. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY


    1. Disconnect airbag connector:


      1. Push down the housing lock and slide the CPA to release the lock.

        Note

        Do not pull while holding the wire harness.

        B000VVMC02
        *a Housing Lock *b CPA
        *c Disconnect the connector lock - -

      2. With the housing lock pushed down again, slide the CPA to disconnect the airbag connector.

      3. After disconnecting the airbag connector, check that the CPA is positioned further back than the housing.

        B000VXLC05
        *a CORRECT *b INCORRECT
        *c CPA *d Housing
    2. B000TTQN01

      Remove the 2 bolts <I>.

    3. for LHD:


      1. B000XHO

        Detach the clamp and disconnect the connector.

      2. B000TPO

        Detach the clamps.

      3. B000UFZ

        Disconnect the connector.

    4. for RHD:


      1. B000USQ

        Detach the clamp and disconnect the connector.

      2. B000ULR

        Detach the clamps.

      3. B000YR6

        Disconnect the connector.

    5. B000YL8

      Disconnect the 2 connectors.

    6. for LHD:


      1. Detach the claws and remove the cooler thermistor (recirculated air temperature) from the instrument panel safety pad sub-assembly.

        B000WGOC01
        *1 Cooler Thermistor (Recirculated Air Temperature) - -
        B000XM7 Bolt <E> B000TT4 Nut <C> or <D>

      2. Detach the clamp.

      3. Remove the 8 bolts <E>, and nut <C> or <D>.

    7. for RHD:


      1. Detach the claws and remove the cooler thermistor (recirculated air temperature) from the instrument panel safety pad sub-assembly.

        B000WZUC04
        *1 Cooler Thermistor (Recirculated Air Temperature) - -
        B000XM7 Bolt <E> B000TT4 Nut <C> or <D>

      2. Remove the 8 bolts <E>, and nut <C> or <D>.

    8. Pull as shown in the illustration to detach the guides.

      B000UD4C01
      B000WYJ Remove in this Direction - -

    9. Lift up the instrument panel safety pad sub-assembly as shown in the illustration to remove it.

      B000WCHC01
      B000WYJ Remove in this Direction - -