CHILD RESTRAINT SEAT TETHER ANCHOR REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the child restraint seat tether anchor bracket removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA/LDA system

Click here

Pre-collision system
Parking assist monitor system

Click here

Steering sensor zero point calibration Variable gear ratio steering system

Click here


  • Front seat assembly LH (Only for removal and installation)

  • Front seat assembly RH (Only for removal and installation)

 Initialize position control ECU Front Power Seat Control System

Click here

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

    Click here

  2. REMOVE FRONT SEAT ASSEMBLY LH

    Click here

  3. REMOVE FRONT SEAT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  4. REMOVE REAR SEAT CUSHION ASSEMBLY

    Click here

  5. REMOVE REAR SEAT CUSHION LOCK HOOK

    Click here

  6. REMOVE REAR SEAT SIDE GARNISH

    Click here

  7. REMOVE REAR SEATBACK COVER

    Click here

  8. REMOVE REAR SEATBACK ASSEMBLY LH

    Click here

  9. REMOVE REAR SEATBACK ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  10. REMOVE QUARTER INSIDE TRIM BOARD LH

    Click here

  11. REMOVE QUARTER INSIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  12. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

    Click here

  13. REMOVE REAR SEAT INNER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the rear No. 1 seat inner belt assembly LH.

  14. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  15. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  16. REMOVE OUTER LAP BELT ANCHOR COVER

    Click here

  17. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH(FLOOR ANCHOR)

    Click here

  18. REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH(FLOOR ANCHOR)

    Tech Tips

    Use the same procedure described for the LH side.

  19. REMOVE QUARTER TRIM PANEL ASSEMBLY LH

    Click here

  20. REMOVE QUARTER TRIM PANEL ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  21. REMOVE CENTER PILLAR GARNISH ASSEMBLY LH

    Click here

  22. REMOVE CENTER PILLAR GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  23. REMOVE INNER ROOF SIDE GARNISH LH

    Click here

  24. REMOVE INNER ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  25. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH

    Click here

  26. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  27. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH

    Click here

  28. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  29. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR COVER

    Tech Tips

    Use the same procedure for the other side.


    1. B000UERC01
      B000WYJ Remove in this Direction

      Using moulding remover A, push in the direction indicated by the arrow shown in the illustration to detach the claws.

    2. Slide in the removal direction shown in the illustration to detach the guides and remove the child restraint seat tether anchor cover.

  30. REMOVE NO. 3 SPEAKER ASSEMBLY WITH BOX

    Click here

  31. REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH(FLOOR ANCHOR)

    Click here

  32. REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH(FLOOR ANCHOR)

    Tech Tips

    Use the same procedure described for the LH side.

  33. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY

    Click here

  34. REMOVE ROOM PARTITION PANEL INSULATOR

    Click here

  35. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET

    Tech Tips

    Use the same procedure for the other side.


    1. B000VRW

      Remove the bolt.

    2. Detach the guide and remove the child restraint seat tether anchor bracket.