FRONT SEAT OUTER BELT ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front seat outer belt assembly LH removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA/LDA system

Click here

Pre-collision system
Parking assist monitor system

Click here

Steering sensor zero point calibration Variable gear ratio steering system

Click here


  • Front seat assembly LH (Only for removal and installation)

  • Front seat assembly RH (Only for removal and installation)

 Initialize position control ECU Front Power Seat Control System

Click here

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

B000WAX

Click here

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

    Click here

  2. REMOVE FRONT SEAT ASSEMBLY LH

    Click here

  3. REMOVE REAR SEAT CUSHION ASSEMBLY

    Click here

  4. REMOVE REAR SEAT CUSHION LOCK HOOK

    Click here

  5. REMOVE REAR SEAT SIDE GARNISH

    Click here

  6. REMOVE REAR SEATBACK COVER

    Click here

  7. REMOVE REAR SEATBACK ASSEMBLY LH

    Click here

  8. REMOVE QUARTER INSIDE TRIM BOARD LH

    Click here

  9. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

    Click here

  10. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  11. REMOVE OUTER LAP BELT ANCHOR COVER


    1. B000VW3C01
      *a Guide A
      *b Guide B
      B000WYJ Remove in this Direction (1)
      B000YNM Remove in this Direction (2)

      Place your hands at the positions shown in the illustration and pull in the removal direction (1) to detach guide A.

    2. Slide in the removal direction (2) shown in the illustration to detach guide B and remove the outer lap belt anchor cover.

  12. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH(FLOOR ANCHOR)


    1. B000VPK

      Remove the bolt and floor anchor of the front seat outer belt assembly LH.

  13. REMOVE QUARTER TRIM PANEL ASSEMBLY LH

    Click here

  14. REMOVE CENTER PILLAR GARNISH ASSEMBLY LH

    Click here

  15. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH


    1. B000U9C

      Remove the bolt and shoulder anchor of the front seat outer belt assembly LH.

    2. B000VCHC01
      *a Locking Button
      *b Release
      B000WCG Protective Tape

      Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.

      Tech Tips

      Tape the screwdriver tip before use.

    3. Disconnect the tension reducer connector.

    4. B000YNX

      Remove the 2 bolts.

    5. Detach the guides and remove the front seat outer belt assembly LH.

  16. REMOVE FRONT SEAT BELT RETRACTOR COVER LH


    1. B000WB1C01
      B000WYJ Remove in this Direction (1)
      B000YNM Remove in this Direction (2)

      Pull in the removal direction (1) shown in the illustration to detach the claw.

    2. Slide in the removal direction (2) shown in the illustration to detach the guide and remove the front seat belt retractor cover LH.