FRONT SEATBACK HEATER INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:


  • Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

B000ZBZ

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL SEPARATE TYPE FRONT SEATBACK COVER (FRONT SEATBACK HEATER) (for Standard Seat Type)

    Tech Tips

    When installing a separate type front seatback cover(front seatback heater), refer to Precaution in order to prevent wrinkles from forming.

    Click here


    1. Set the separate type front seatback cover(front seatback heater) on the separate type front seatback pad.

    2. Using hog ring pliers, install the separate type front seatback cover(front seatback heater) to the separate type front seatback pad with 9 new hog rings in the order indicated in the illustration.

      B000VXPC01
      *a Hog Ring Pliers - -

      Note


      • Be careful not to damage the separate type front seatback cover(front seatback heater).

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover(front seatback heater).

    3. B000YW4C02
      B000WYJ Install in this Direction

      Pass the bracket of the separate type front seatback cover(front seatback heater) through the hole on the separate type front seatback pad.

  2. INSTALL FRONT SEATBACK PAD WITH COVER LH (FRONT SEATBACK HEATER) (for Sports Seat Type)


    1. Set the front seatback pad with cover LH(front seatback heater) on the front seatback frame sub-assembly LH.

    2. B000WNAC02
      *a Bracket

      Attach the wire harness clamp.

    3. Install the bracket with a new nut.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Note


      • Be sure to wrap the front seat airbag assembly LH with the bracket when installing.

      • Check that the band is not twisted after installing the bracket.

      • If the bracket is not securely installed, the front seat airbag assembly LH may not deploy properly. For this reason, the bracket must be securely installed.

    4. B000X8CC01
      *a Fastener
      *b Pocket
      B000WYJ Close in this Direction

      Close the fasteners and insert them into the pockets.

    5. B000VUP

      Attach the hooks.

  3. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Standard Seat Type)

    Click here

  4. INSTALL FRONT UPPER SEATBACK COVER SUB-ASSEMBLY LH (for Standard Seat Type)

    Click here

  5. INSTALL FRONT SEAT HEADREST SUPPORT (for Standard Seat Type)

    Click here

  6. INSTALL FRONT SEAT HEADREST SUPPORT (for Sports Seat Type)

    Click here

  7. INSTALL FRONT SEATBACK SUB-ASSEMBLY LH (FRONT SEATBACK HEATER) (for Standard Seat Type)


    1. B000VRYC01
      B000WYJ Install in this Direction

      Push in the installation direction shown in the illustration to attach the hooks and temporarily install the front seatback sub-assembly LH(front seatback heater).

    2. B000WI8C01
      *a Hook
      *b Hole
      B000WYJ Install in this Direction

      Fold back the separate type front seatback cover.

    3. B000XY3C02
      *a Fastening Tape

      Attach the fastening tape.

    4. Pass the hooks through the hole on the separate type front seatback cover.

    5. B000W2H

      Attach the hooks.

    6. B000XD7

      Fold back the front upper seatback cover sub-assembly LH and install the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    7. B000WI9

      Fold back the front upper seatback cover sub-assembly LH and install the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    8. B000XGB

      Fold back the front upper seatback cover sub-assembly LH and install the bolt.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    9. Return the front upper seatback cover sub-assembly LH.

    10. B000X4BC01
      *a Wire Harness Clamp
      *b Hook
      B000WYJ Install in this Direction

      Pass the wire harness of the front seatback sub-assembly LH(front seatback heater) through the hole on the separate type front seatback cover.

    11. Connect the connector and attach the wire harness clamp.

    12. Attach the hooks.

    13. B000WMQC01
      B000WYJ Close in this Direction

      Return the separate type front seatback cover and close the fasteners.

    14. B000YUF

      Attach the hooks.

  8. INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY LH

    Click here

  9. INSTALL SEAT ADJUSTER COVER CAP LH

    Click here

  10. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY

    Click here

  11. INSTALL LIMIT SWITCH ASSEMBLY

    Click here

  12. INSTALL FRONT INNER SEAT CUSHION SHIELD LH

    Click here

  13. INSTALL FRONT SEAT CUSHION SHIELD LH

    Click here

  14. INSTALL FRONT SEAT ASSEMBLY LH

    Click here

  15. INITIALIZATION OF SEAT ECU

    Click here