FRONT SEAT ASSEMBLY INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:


  • Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

B000ZBZ

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL FRONT SEAT ASSEMBLY LH


    1. B000U2O

      Place the front seat assembly LH in the cabin.

      Note


      • 2 or more people are required when carrying the front seat assembly LH out of the vehicle.

      • Protect the front seat legs.

      • Do not damage the front seat assembly LH, body exterior or interior parts.

    2. Tilt the front seat assembly LH backward.

      Note

      Do not damage the front seat assembly LH or interior parts.

    3. B000WX2C05
      *a Front Seat Airbag Assembly LH Connector

      Connect the 3 connectors and attach the wire harness protector clamps.

    4. Connect the front seat airbag assembly LH connector under the front seat assembly LH.


      1. Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

        B000W2VC02
        *a Correct *b Incorrect
        *c Yellow CPA - -

      2. Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

        Note


        • Be careful not to damage the connector or wire harness of the front seat airbag assembly LH.

        • When connecting the connector, make sure to push it straight in.

        • Do not hold any parts other than the yellow CPA when connecting the connector.

        • If the upper portion of the yellow CPA is held when connecting the connector, the partial connection prevention mechanism will not function due to deformation of the yellow CPA. Therefore, hold the sides of the yellow CPA.

    5. Insert the location pin of the front seat assembly LH on the seat rail front side into the hole on the vehicle side.

    6. Temporarily install the front seat assembly LH with the 4 "TORX" screws.

    7. Connect the cable to the negative (-) battery terminal.

      Click here

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

    8. Operate the slide and vertical power seat switch knob to slide the front seat assembly LH to the rearmost position.

    9. B000UL1N01

      Using a T50 "TORX" socket wrench, tighten the 2 "TORX" screws in the order shown in the illustration.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

    10. Operate the slide and vertical power seat switch knob to slide the front seat assembly LH to the frontmost position.

    11. B000UDIN01

      Using a T50 "TORX" socket wrench, tighten the 2 "TORX" screws in the order shown in the illustration.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  2. INSTALL INNER SEAT TRACK BRACKET COVER LH


    1. B000YK3C01
      *a Guide Pin
      B000WYJ Install in this Direction

      Slide in the installation direction shown in the illustration to attach the guides.

    2. Attach the guide pin to install the inner seat track bracket cover LH.

  3. INSTALL OUTER SEAT TRACK COVER LH


    1. B000YIOC01
      *a Guide Pin
      B000WYJ Install in this Direction (1)
      B000YNM Install in this Direction (2)

      Slide in the installation direction (1) shown in the illustration to attach the guides and guide pin.

    2. Push in the installation direction (2) shown in the illustration, attach the claws and install the outer seat track cover LH.

  4. INSTALL FRONT INNER SEAT TRACK BRACKET COVER LH


    1. Operate the slide and vertical power seat switch knob to slide the front seat assembly LH to the rearmost position.

    2. B000VB0C01
      B000WYJ Install in this Direction (1)
      B000YNM Install in this Direction (2)

      Slide in the installation direction (1) shown in the illustration to attach the guides.

    3. Push in the installation direction (2) shown in the illustration, attach the claws and install the front inner seat track bracket cover LH.

  5. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER LH


    1. B000W59C02
      B000WYJ Install in this Direction (1)
      B000YNM Install in this Direction (2)

      Slide in the installation direction (1) shown in the illustration to attach the guides.

    2. Push in the installation direction (2) shown in the illustration, attach the claws and install the front outer seat track bracket cover LH.

  6. INSTALL FRONT SEAT HEADREST ASSEMBLY


    1. Operate the slide and vertical power seat switch knob to set the seat cushion height of the front seat assembly LH to the uppermost position.

    2. Operate the reclining power seat switch knob to adjust the seatback of the front seat assembly LH to a position where the front seat headrest assembly can be installed.

    3. for Standard Seat Type:


      1. Connect the connector.

    4. While pressing the lock release knob, slowly insert the front seat headrest assembly until it reaches the bottom.

      Note

      Lightly lift the front seat headrest assembly upwards and check that it locks.

  7. INSTALL NO. 2 DECK BOARD

    Click here

  8. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM


    1. Reset the auto tilt away function setting to the previous condition by changing the customize parameter.

      Click here

  9. INITIALIZATION OF SEAT ECU

    Click here

  10. INSPECT SRS WARNING LIGHT

    Click here

  11. INSPECT SEAT BELT WARNING SYSTEM

    Click here

  12. INSPECT FRONT SEAT ASSEMBLY

    Click here

  13. INSPECT SEAT HEATER SYSTEM (w/ Seat Heater System)

    Click here

  14. INSPECT CLIMATE CONTROL SEAT SYSTEM

    Click here