SIDE AIRBAG SENSOR INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL DOOR SIDE AIRBAG SENSOR LH


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:


      • B000Y52

        Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • B000VJQ

        If this procedure is performed without disconnecting the negative (-) battery terminal, the airbag may deploy even if an impact is applied only to the door side airbag sensor LH. Therefore, make sure that the negative (-) battery terminal is disconnected before performing this procedure.

    3. Attach the claw to hold the door side airbag sensor LH in place.

    4. Install the nut.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

      Note


      • If the door side airbag sensor LH has been dropped, replace it with a new one.

      • When installing the door side airbag sensor LH, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

      • Tighten the nut while holding the door side airbag sensor LH.

    5. Check that there is no looseness in the installation parts of the door side airbag sensor LH.

    6. Connect the airbag connector.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.


      1. Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

        B000XAKC29
        *a Correct *b Incorrect
        *c CPA *d Housing

      2. While holding the CPA be sure to engage the connectors until they are locked and check that the CPA is in its original position (when locking, make sure that a click sound can be heard).

        Note

        Do not push down the upper part of the CPA shown in the illustration when connecting the airbag connector.

        B000UWBC31
        *a CPA Upper Part *b Housing Lock
        *c CPA *d Connection is Completed

  2. INSTALL NO. 1 FRONT DOOR HOLE COVER SUB-ASSEMBLY LH


    1. for Driver Side:


      1. Align with the installation holes on the vehicle side and No. 1 front door hole cover sub-assembly LH.

      2. B000Z0JC02
        *a Knob
        *b Lock Mark
        *c Lock Position
        B000WYJ Rotate in this Direction

        Pass the new clip through the installation holes so that the clip knob is perpendicular.

      3. With the clip knob installed perpendicular, rotate the clip knob 45° clockwise to align it to the lock mark and lock it.

        Note

        Do not reuse the clips after removing it.

        Tech Tips

        Use the same procedure for the other clips.

    2. for Passenger Side:


      1. Align with the installation holes on the vehicle side and No. 1 front door hole cover sub-assembly RH.

      2. B000ULNC02
        *a Knob
        *b Lock Mark
        *c Lock Position
        B000WYJ Rotate in this Direction

        Pass the new clip through the installation holes so that the clip knob is perpendicular.

      3. With the clip knob installed perpendicular, rotate the clip knob 45° clockwise to align it to the lock mark and lock it.

        Note

        Do not reuse the clips after removing it.

        Tech Tips

        Use the same procedure for the other clips.

    3. Check that the clip knob is in the lock position.

  3. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH (for Driver Side)

    Click here

  4. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY RH (for Front Passenger Side)

    Click here

  5. INSTALL FRONT DOOR TRIM COVER SUB-ASSEMBLY LH (for Driver Side)

    Click here

  6. INSTALL FRONT DOOR ASSIST GRIP ASSEMBLY RH (for Front Passenger Side)

    Click here

  7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Click here

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  8. INSTALL NO. 2 DECK BOARD

    Click here

  9. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  10. CHECK SRS WARNING LIGHT

    Click here