POP UP HOOD LIFTER(for Rear Side) DISPOSAL

CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any pop up hood lifter, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:


    • An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

    • Do not perform this procedure indoors or on rough roads where safety cannot be ensured. Also, do not deploy SRS parts near residential areas.

    • If this procedure is performed indoors or on rough roads where safety cannot be ensured, unforeseen injuries may occur. Also, the deployment noise creates a nuisance to nearby residents.

    B000YKX

    Tech Tips

    When scrapping a vehicle equipped with an SRS or disposing of the No. 2 pop up hood lifter assembly LH assembly, be sure to deploy the No. 2 pop up hood lifter assembly LH first in accordance with the procedure described below. If any abnormality occurs with the No. 2 pop up hood lifter assembly LH deployment, contact the Service Dept. of the distributor.

  2. DISPOSE OF NO. 2 POP UP HOOD LIFTER ASSEMBLY LH (When Installed in Vehicle)

    Note


    • When disposing of a No. 2 pop up hood lifter assembly LH, use an unneeded vehicle to deploy the No. 2 pop up hood lifter assembly LH.

    • Be sure to observe the following procedure when deploying the No. 2 pop up hood lifter assembly LH.

    Tech Tips

    Prepare a battery as the power source to deploy the No. 2 pop up hood lifter assembly LH.


    1. B000WWRN08

      Check the function of SST.

      Click here

      SST
      09082-00700

    2. Refer to Precaution.

      Click here

    3. Remove the No. 2 deck board.

      Click here

    4. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      B000Y52

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the airbag deploys for any reason, it may cause a serious accident.

    5. Remove the radiator support to frame seal RH.

      Click here

    6. Remove the radiator support to frame seal LH.

      Click here

    7. Remove the lower radiator air deflector.

      Click here

    8. Remove the front fender reinforcement top sub-assembly LH.

      Click here

    9. Remove the No. 3 cowl top panel insulator.


      1. for LHD:

        Click here

        for RHD:

        Click here

    10. B000WVTC01
      *a Housing Lock
      *b CPA
      *c CPA Upper Part
      B000WYJ Slide

      Disconnect No. 2 pop up hood lifter assembly LH connector.

      Note

      When disconnecting any No. 2 pop up hood lifter assembly LH connector, take care not to damage the wire harness.


      1. Push down the housing lock and slide the CPA. (At this time, the connector cannot be disconnected yet.)

      2. Push the housing lock again and disconnect the connector.

        Note

        Do not push down the upper part of the CPA shown in the illustration when disconnecting the No. 2 pop up hood lifter assembly LH connector.

    11. Install SST.

      CAUTION:

      Check that there is no looseness in the No. 2 pop up hood lifter assembly LH.


      1. B000WRCN01

        Connect the SST connector to the airbag connector.

        SST
        09082-00700
        09082-00820

        Note

        To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.

        CAUTION:


        • B000XPN

          Do not deploy if the No. 2 pop up hood lifter assembly LH is loose.

        • If deployed while the No. 2 pop up hood lifter assembly LH is loose, the No. 2 pop up hood lifter assembly LH may fly off and cause serious injuries.

      2. B000UXJC02
        *a 10 m (32.8 ft.) or more

        Move SST at least 10 m (32.8 ft.) away from the engine compartment of the vehicle.

      3. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

    12. Close the engine hood.

      CAUTION:

      Check that the engine hood is locked.

    13. Deploy the No. 2 pop up hood lifter assembly LH.


      1. Check that no one is within a 10 m (32.8 ft.) radius of the vehicle.

      2. Press the SST activation switch to deploy the No. 2 pop up hood lifter assembly LH.

        CAUTION:


        • Do not deploy with people inside or around the vehicle.

        • If deployed with people inside or around the vehicle, serious injuries may occur.

        B000VKW

        Tech Tips

        The No. 2 pop up hood lifter assembly LH is deployed as the LED of the SST activation switch comes on.

    14. Remove the No. 2 pop up hood lifter assembly LH.

      Click here

      CAUTION:


      • B000X62

        The No. 2 pop up hood lifter assembly LH becomes extremely hot when the No. 2 pop up hood lifter assembly LH is deployed, so do not touch it for at least 30 minutes after deployment.

      • If not left alone for 30 minutes or more, burns may occur when touched.

      • B000V7H

        Do not apply water etc. to a No. 2 pop up hood lifter assembly LH with a deployed No. 2 pop up hood lifter assembly LH.

      • If water is applied to the No. 2 pop up hood lifter assembly LH immediately after deployment, burns may occur from the resulting steam.

      • B000WVE

        Always wear safety glasses and gloves when handling a deployed No. 2 pop up hood lifter assembly LH.

      • If the No. 2 pop up hood lifter assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

      • After removal, quickly seal the No. 2 pop up hood lifter assembly LH in a plastic bag.

    15. Place the No. 2 pop up hood lifter assembly LH in a plastic bag, tie it tightly, and dispose of it according to local regulations.

      CAUTION:


      • B000U3L

        The No. 2 pop up hood lifter assembly LH becomes extremely hot when the No. 2 pop up hood lifter assembly LH is deployed, so do not touch it for at least 30 minutes after deployment.

      • If not left alone for 30 minutes or more, burns may occur when touched.

      • B000Y1I

        Do not apply water etc. to a No. 2 pop up hood lifter assembly LH with a deployed No. 2 pop up hood lifter assembly LH.

      • If water is applied to the No. 2 pop up hood lifter assembly LH immediately after deployment, burns may occur from the resulting steam.

      • B000YLC

        Always wear safety glasses and gloves when handling a deployed No. 2 pop up hood lifter assembly LH.

      • If the No. 2 pop up hood lifter assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

      • B000YIN

        Never dispose of a No. 2 pop up hood lifter assembly LH with an undeployed No. 2 pop up hood lifter assembly LH.

      • If an undeployed No. 2 pop up hood lifter assembly LH is disposed of, and then deploys for any reason, unforeseen injuries may occur.

      • Always wash your hands with water after completing the operation.

  3. DISPOSE OF NO. 2 POP UP HOOD LIFTER ASSEMBLY LH (When not Installed in Vehicle)

    Note

    Be sure to observe the following procedure when deploying the No. 2 pop up hood lifter assembly LH.

    Tech Tips

    Prepare a battery as the power source to deploy the No. 2 pop up hood lifter assembly LH.


    1. B000WWRN08

      Check the function of SST.

      Click here

      SST
      09082-00700

    2. Remove the No. 2 pop up hood lifter assembly LH.

      Click here

      CAUTION:

      B000Y52

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the No. 2 pop up hood lifter assembly LH deploys for any reason, it may cause a serious accident.

    3. B000WCQC16
      *a Wire Diameter
      *b Stripped Wire Cross Sectional Area

      Using braided wire, tie down the No. 2 pop up hood lifter assembly LH to an unneeded tire.

      Wire
      Cross-sectional area of stripped wire
      1.25 mm2 (0.0019 in.2) or more

      CAUTION:

      If the wire is too thin or an alternative object is used to tie down the No. 2 pop up hood lifter assembly LH, it may snap when the No. 2 pop up hood lifter assembly LH is deployed. Always use a wire for vehicle use with a cross sectional area of at least 1.25 mm2(0.0019 in.2).

      Tech Tips

      To calculate the area of the cross-sectional area of stripped wire:

      Cross sectional area = 3.14 x (Diameter)2/ 4


      1. B000Z20C02
        *a Width
        *b Inner Diameter
        *c extended section

        Position the No. 2 pop up hood lifter assembly LH inside the tire as shown in the illustration.

        Minimum tire size
        Must exceed the following dimensions
        Width
        185 mm (7.28 in.)
        Inner diameter
        360 mm (1.18 ft.)

        Note

        The tire may be damaged by the No. 2 pop up hood lifter assembly LH deployment, so use unneeded tire.

        Tech Tips

        Through the wire to pop up hood lifter installation hole.

    4. Install SST.


      1. B000WAPN01

        Connect the SST connector to the No. 2 pop up hood lifter assembly LH.

        SST
        09082-00820

    5. Place the tires.


      1. B000XEEC01
        *a Tires (2 or more)

        Place at least 2 tires under the tire to which the No. 2 pop up hood lifter assembly LH is tied.

      2. Place at least 2 tires onto the tire to which the No. 2 pop up hood lifter assembly LH is tied. The top tire should have a wheel installed.

        Note


        • Do not place the SST connector under the tire because it could be damaged.

        • The wheel and tires may be damaged by the No. 2 pop up hood lifter assembly LH deployment, so use an unneeded wheel and tires.

      3. B000YZU

        Tie the tires together with 2 wires.

        CAUTION:

        Make sure that the wires are tight. Looseness in the wires will result in the tires breaking loose when the No. 2 pop up hood lifter assembly LH is deployed.

    6. Install SST.


      1. B000UYJC01
        *a 10 m (32.8 ft.) or more

        Connect the SST connector.

        SST
        09082-00700

        Note

        To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.

      2. Move SST at least 10 m (32.8 ft.) away from the No. 2 pop up hood lifter assembly LH tied down to the tire.

    7. Deploy the No. 2 pop up hood lifter assembly LH.


      1. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

      2. Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the No. 2 pop up hood lifter assembly LH is tied.

      3. Press the SST activation switch to deploy the No. 2 pop up hood lifter assembly LH.

        CAUTION:


        • Do not deploy with people around the tire.

        • If deployed with people around the tire, serious injuries may occur.

        B000WVJ

        Tech Tips

        The No. 2 pop up hood lifter assembly LH is deployed as the LED of the SST activation switch comes on.

    8. Dispose of the No. 2 pop up hood lifter assembly LH.

      CAUTION:


      • B000U3L

        The No. 2 pop up hood lifter assembly LH becomes extremely hot when the No. 2 pop up hood lifter assembly LH is deployed, so do not touch it for at least 30 minutes after deployment.

      • If not left alone for 30 minutes or more, burns may occur when touched.

      • B000Y1I

        Do not apply water etc. to a No. 2 pop up hood lifter assembly LH with a deployed No. 2 pop up hood lifter assembly LH.

      • If water is applied to the No. 2 pop up hood lifter assembly LH immediately after deployment, burns may occur from the resulting steam.

      • B000YLC

        Always wear safety glasses and gloves when handling a deployed No. 2 pop up hood lifter assembly LH.

      • If the No. 2 pop up hood lifter assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

      • B000YIN

        Never dispose of a No. 2 pop up hood lifter assembly LH with an undeployed No. 2 pop up hood lifter assembly LH.

      • If an undeployed No. 2 pop up hood lifter assembly LH is disposed of, and then deploys for any reason, unforeseen injuries may occur.

      • Always wash your hands with water after completing the operation.


      1. Remove the No. 2 pop up hood lifter assembly LH from the tire.

      2. Place the No. 2 pop up hood lifter assembly LH in a plastic bag, tie it tightly, and dispose of it according to local regulations.