POP UP HOOD LIFTER(for Front Side) DISPOSAL

CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any pop up hood lifter, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. PRECAUTION

    CAUTION:


    • An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

    • Do not perform this procedure indoors or on rough roads where safety cannot be ensured. Also, do not deploy SRS parts near residential areas.

    • If this procedure is performed indoors or on rough roads where safety cannot be ensured, unforeseen injuries may occur. Also, the deployment noise creates a nuisance to nearby residents.

      B000UP0

    Tech Tips

    When scrapping a vehicle equipped with an SRS or disposing of the pop up hood lifter assembly LH, be sure to deploy the pop up hood lifter assembly LH first in accordance with the procedure described below. If any abnormality occurs with the pop up hood lifter assembly LH deployment, contact the Service Dept. of the distributor.

  2. DISPOSE OF POP UP HOOD LIFTER ASSEMBLY LH (When Installed in Vehicle)

    Note


    • When disposing of a pop up hood lifter assembly LH, use an unneeded vehicle to deploy the pop up hood lifter assembly LH.

    • Be sure to observe the following procedure when deploying the pop up hood lifter assembly LH.

    Tech Tips

    Prepare a battery as the power source to deploy the pop up hood lifter assembly LH.


    1. B000WWRN08

      Check the function of SST.

      Click here

      SST
      09082-00700

    2. Refer to Precaution.

      Click here

    3. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      B000Y52

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the pop up hood lifter assembly LH deploys for any reason, it may cause a serious accident.

    4. Remove the front airbag sensor LH.

      Click here

    5. B000WVTC01
      *a Housing Lock
      *b CPA
      *c CPA Upper Part
      B000WYJ Slide

      Disconnect pop up hood lifter assembly LH connector.

      Note

      When disconnecting any pop up hood lifter assembly LH connector, take care not to damage the wire harness.


      1. Push down the housing lock and slide the CPA. (At this time, the connector cannot be disconnected yet.)

      2. Push the housing lock again and disconnect the connector.

        Note

        Do not push down the upper part of the CPA shown in the illustration when disconnecting the pop up hood lifter assembly LH connector.

    6. Install SST.

      CAUTION:

      Check that there is no looseness in the pop up hood lifter assembly LH.


      1. B000YG1N01

        Connect the SST connector to the pop up hood lifter assembly LH connector.

        SST
        09082-00700
        09082-00820

        CAUTION:


        • B000W9W

          Do not deploy if the pop up hood lifter assembly LH is loose.

        • If deployed while the pop up hood lifter assembly LH is loose, the pop up hood lifter assembly LH may fly off and cause serious injuries.

        Note

        To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.

      2. B000UXJC02
        *a 10 m (32.8 ft.) or more

        Move SST at least 10 m (32.8 ft.) away from the engine compartment of the vehicle.

      3. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

    7. Close the engine hood.

      CAUTION:

      Check that the engine hood is locked.

    8. Deploy the pop up hood lifter assembly LH.


      1. Check that no one is within a 10 m (32.8 ft.) radius of the vehicle.

      2. Press the SST activation switch to deploy the pop up hood lifter assembly LH.

        CAUTION:


        • Do not deploy with people inside or around the vehicle.

        • If deployed with people inside or around the vehicle, serious injuries may occur.

        B000UH3

        Tech Tips

        The pop up hood lifter assembly LH is deployed as the LED of the SST activation switch comes on.

    9. Remove the pop up hood lifter assembly LH.

      Click here

      CAUTION:


      • B000YCT

        The pop up hood lifter assembly LH becomes extremely hot when the pop up hood lifter assembly LH is deployed, so do not touch it for at least 30 minutes after deployment.

      • If not left alone for 30 minutes or more, burns may occur when touched.

      • B000TUH

        Do not apply water etc. to a pop up hood lifter assembly LH with a deployed pop up hood lifter assembly LH.

      • If water is applied to the pop up hood lifter assembly LH immediately after deployment, burns may occur from the resulting steam.

      • B000Y0E

        Always wear safety glasses and gloves when handling a deployed pop up hood lifter assembly LH.

      • If the pop up hood lifter assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

      • After removal, quickly seal the pop up hood lifter assembly LH in a plastic bag.

    10. Dispose of the pop up hood lifter assembly LH.


      1. Place the pop up hood lifter assembly LH in a plastic bag, tie it tightly and dispose of it according to local regulations.

        CAUTION:


        • B000W7J

          The pop up hood lifter assembly LH becomes extremely hot when the pop up hood lifter assembly LH is deployed, so do not touch it for at least 30 minutes after deployment.

        • If not left alone for 30 minutes or more, burns may occur when touched.

        • B000TY3

          Do not apply water etc. to a pop up hood lifter assembly LH with a deployed pop up hood lifter assembly LH.

        • If water is applied to the pop up hood lifter assembly LH immediately after deployment, burns may occur from the resulting steam.

        • B000XZG

          Always wear safety glasses and gloves when handling a deployed pop up hood lifter assembly LH.

        • If the pop up hood lifter assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

        • B000YVG

          Never dispose of a pop up hood lifter assembly LH with an undeployed pop up hood lifter assembly LH.

        • If an undeployed pop up hood lifter assembly LH is disposed of, and then deploys for any reason, unforeseen injuries may occur.

        • Always wash your hands with water after completing the operation.

  3. DISPOSE OF POP UP HOOD LIFTER ASSEMBLY LH (When not Installed in Vehicle)

    Note

    Be sure to observe the following procedure when deploying the pop up hood lifter assembly LH.

    Tech Tips

    Prepare a battery as the power source to deploy the pop up hood lifter assembly LH.


    1. B000WWRN08

      Check the function of SST.

      Click here

      SST
      09082-00700

    2. Remove the pop up hood lifter assembly LH.

      Click here

      CAUTION:

      B000Y52

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • If the pop up hood lifter assembly LH deploys for any reason, it may cause a serious accident.

    3. B000WCQC16
      *a Wire Diameter
      *b Stripped Wire Cross Sectional Area

      Using braided wire, tie down the pop up hood lifter assembly LH to an unneeded tire.

      Wire
      Cross-sectional area of stripped wire
      1.25 mm2 (0.0019 in.2) or more

      CAUTION:

      If the wire is too thin or an alternative object is used to tie down the pop up hood lifter assembly LH, it may snap when the pop up hood lifter assembly LH is deployed. Always use a wire for vehicle use with a cross sectional area of at least 1.25 mm2(0.0019 in.2).

      Tech Tips

      To calculate the area of the cross-sectional area of stripped wire:

      Cross sectional area = 3.14 x (Diameter)2/ 4


      1. B000YLDC01
        *a Width
        *b Inner Diameter
        *c Extended Section

        Position the pop up hood lifter assembly LH inside the tire as shown in the illustration.

        Minimum tire size
        Must exceed the following dimensions
        Width
        185 mm (7.28 in.)
        Inner diameter
        360 mm (1.18 ft.)

        Note

        The tire may be damaged by the pop up hood lifter assembly LH deployment, so use unneeded tire.

    4. Install SST.


      1. B000YX4N01

        Connect the SST connector to the pop up hood lifter assembly LH.

        SST
        09082-00820

    5. Place the tires.


      1. B000YC1C01
        *a Tires (2 or more)

        Place at least 2 tires under the tire to which the pop up hood lifter assembly LH is tied.

      2. Place at least 2 tires onto the tire to which the pop up hood lifter assembly LH is tied. The top tire should have a wheel installed.

        Note


        • Do not place the SST connector under the tire because it could be damaged.

        • The wheel and tires may be damaged by the pop up hood lifter assembly LH deployment, so use an unneeded wheel and tires.

      3. B000YZU

        Tie the tires together with 2 wires.

        CAUTION:

        Make sure that the wires are tight. Looseness in the wires will result in the tires breaking loose when the pop up hood lifter assembly LH is deployed.

    6. Install SST.


      1. B000VGKC01
        *a 10 m (32.8 ft.) or more

        Connect the SST connector.

        SST
        09082-00700

        Note

        To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.

      2. Move SST at least 10 m (32.8 ft.) away from the pop up hood lifter assembly LH tied down to the tire.

    7. Deploy the pop up hood lifter assembly LH.


      1. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

      2. Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the pop up hood lifter assembly LH is tied.

      3. Press the SST activation switch to deploy the pop up hood lifter assembly LH.

        CAUTION:


        • Do not deploy with people around the tire.

        • If deployed with people around the tire, serious injuries may occur.

        B000WVJ

        Tech Tips

        The pop up hood lifter assembly LH is deployed as the LED of the SST activation switch comes on.

    8. Dispose of the pop up hood lifter assembly LH.

      CAUTION:


      • B000W7J

        The pop up hood lifter assembly LH becomes extremely hot when the pop up hood lifter assembly LH is deployed, so do not touch it for at least 30 minutes after deployment.

      • If not left alone for 30 minutes or more, burns may occur when touched.

      • B000TY3

        Do not apply water etc. to a pop up hood lifter assembly LH with a deployed pop up hood lifter assembly LH.

      • If water is applied to the pop up hood lifter assembly LH immediately after deployment, burns may occur from the resulting steam.

      • B000XZG

        Always wear safety glasses and gloves when handling a deployed pop up hood lifter assembly LH.

      • If the pop up hood lifter assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

      • B000YVG

        Never dispose of a pop up hood lifter assembly LH with an undeployed pop up hood lifter assembly LH.

      • If an undeployed pop up hood lifter assembly LH is disposed of, and then deploys for any reason, unforeseen injuries may occur.

      • Always wash your hands with water after completing the operation.


      1. Remove the pop up hood lifter assembly LH from the tire.

      2. Place the pop up hood lifter assembly LH in a plastic bag, tie it tightly, and dispose of it according to local regulations.