AIRBAG SYSTEM, Diagnostic DTC:B1835/58, B1836/58, B1837/58, B1838/58

DTC Code DTC Name
B1835/58 Short in Curtain Shield Squib LH Circuit
B1836/58 Open in Curtain Shield Squib LH Circuit
B1837/58 Short to GND in Curtain Shield Squib LH Circuit
B1838/58 Short to B+ in Curtain Shield Squib LH Circuit

DESCRIPTION

The curtain shield squib LH circuit consists of the airbag ECU assembly and curtain shield airbag assembly LH.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the curtain shield squib LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1835/58 Short in Curtain Shield Squib LH Circuit

One of the following conditions is met:


  • The airbag ECU assembly detects a line short circuit signal 5 times in the curtain shield squib LH circuit during the primary check.

  • A curtain shield airbag assembly LH malfunction.

  • An airbag ECU assembly malfunction.

  • Floor wire

  • Curtain shield airbag assembly LH

  • Airbag ECU assembly

 Comes on Applicable
B1836/58 Open in Curtain Shield Squib LH Circuit

One of the following conditions is met:


  • The airbag ECU assembly detects an open circuit signal in the curtain shield squib LH circuit for 2 seconds.

  • A curtain shield airbag assembly LH malfunction.

  • An airbag ECU assembly malfunction.

  • Floor wire

  • Curtain shield airbag assembly LH

  • Airbag ECU assembly

 Comes on Applicable
B1837/58 Short to GND in Curtain Shield Squib LH Circuit

One of the following conditions is met:


  • The airbag ECU assembly detects a short circuit to ground signal in the curtain shield squib LH circuit for 0.5 seconds.

  • A curtain shield airbag assembly LH malfunction.

  • An airbag ECU assembly malfunction.

  • Floor wire

  • Curtain shield airbag assembly LH

  • Airbag ECU assembly

 Comes on Applicable
B1838/58 Short to B+ in Curtain Shield Squib LH Circuit

One of the following conditions is met:


  • The airbag ECU assembly detects a short circuit to B+ signal in the curtain shield squib LH circuit for 0.5 seconds.

  • A curtain shield airbag assembly LH malfunction.

  • An airbag ECU assembly malfunction.

  • Floor wire

  • Curtain shield airbag assembly LH

  • Airbag ECU assembly

 Comes on Applicable

WIRING DIAGRAM

B000X65E28
*a Curtain Shield Airbag Assembly LH
*b Airbag ECU Assembly

CAUTION / NOTICE / HINT

Note


  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

    Click here

Tech Tips

To perform the simulation method, enter check mode (signal check) with the GTS (Click here ), and then wiggle each connector of the airbag system or drive the vehicle on various types of road Click here.

Click here

PROCEDURE


  1. CHECK CONNECTORS


    1. B000YSRC33
      *1 Curtain Shield Airbag Assembly LH
      *2 Airbag ECU Assembly
      *3 Floor Wire

      Turn the engine switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the curtain shield airbag assembly LH and airbag ECU assembly.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the curtain shield airbag assembly LH and airbag ECU assembly.

    5. Check that the terminals of the connectors are not deformed or damaged.

      OK
      The terminals are not deformed or damaged.

    6. Check that the floor wire connector (on the curtain shield airbag assembly LH side) is not loose, deformed or damaged.

      OK
      The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.

    7. Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.

      OK
      The short springs are not deformed or damaged.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  2. CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH


    1. B000YRWC18
      *1 Curtain Shield Airbag Assembly LH
      *2 Airbag ECU Assembly
      *3 SST
      *a

      Front view of wire harness connector

      (to Curtain Shield Airbag Assembly LH)

      Connect the connector to the airbag ECU assembly.

    2. Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

      CAUTION:

      Never connect the tester to the curtain shield airbag assembly LH for measurement, as this may lead to a serious injury due to airbag deployment.

      Note


      • Do not forcibly insert SST into the terminals of the connector when connecting SST.

      • Insert SST straight into the terminals of the connector.

      SST
      09843-18061

    3. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    4. Turn the engine switch on (IG), and wait for at least 60 seconds.

    5. Clear the DTCs.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the engine switch off.

    7. Turn the engine switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      Result
      Proceed to
      DTC B1835/58, B1836/58, B1837/58 or B1838/58 is not output
      DTC B1835/58, B1836/58, B1837/58 or B1838/58 is output

      Tech Tips

      Codes other than DTC B1835/58, B1836/58, B1837/58 and B1838/58 may be output at this time, but they are not related to this check.

    9. Turn the engine switch off.

    10. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    11. Disconnect SST from connector C.


    DTC B1835/58, B1836/58, B1837/58 or B1838/58 is not output

    REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY LH Click here

    DTC B1835/58, B1836/58, B1837/58 or B1838/58 is output

  3. CHECK FLOOR WIRE


    1. B000TWWC03
      *1 Curtain Shield Airbag Assembly LH
      *2 Airbag ECU Assembly
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Curtain Shield Airbag Assembly LH)
      B000XM7 Release the activation prevention mechanism

      Disconnect the floor wire from the airbag ECU assembly.

    2. Check for a short to B+ in the circuit.


      1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

      2. Turn the engine switch on (IG).

      3. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Switch Condition Specified Condition
        X62-1 (ICL+) - Body ground Engine switch on (IG) Below 1 V
        X62-2 (ICL-) - Body ground Engine switch on (IG) Below 1 V

      4. Turn the engine switch off.

      5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Check for an open in the circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        X62-1 (ICL+) - X62-2 (ICL-) Always Below 1 Ω

    4. Check for a short to ground in the circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        X62-1 (ICL+) - Body ground Always 1 MΩ or higher
        X62-2 (ICL-) - Body ground Always 1 MΩ or higher

    5. Check for a short in the circuit.


      1. Release the activation prevention mechanism built into connector B.

        Click here

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        X62-1 (ICL+) - X62-2 (ICL-) Always 1 MΩ or higher

      3. Restore the released activation prevention mechanism of connector B to the original condition.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  4. CHECK DTC


    1. B000ZCIC12
      *1 Curtain Shield Airbag Assembly LH
      *2 Airbag ECU Assembly

      Connect the connectors to the curtain shield airbag assembly LH and airbag ECU assembly.

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Turn the engine switch on (IG), and wait for at least 60 seconds.

    4. Clear the DTCs.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the engine switch off.

    6. Turn the engine switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      Result
      Proceed to
      DTC B1835/58, B1836/58, B1837/58 or B1838/58 is not output
      DTC B1835/58, B1836/58, B1837/58 or B1838/58 is output

      Tech Tips

      Codes other than DTC B1835/58, B1836/58, B1837/58 and B1838/58 may be output at this time, but they are not related to this check.


    DTC B1835/58, B1836/58, B1837/58 or B1838/58 is not output

    USE SIMULATION METHOD TO CHECK Click here

    DTC B1835/58, B1836/58, B1837/58 or B1838/58 is output

    REPLACE AIRBAG ECU ASSEMBLY Click here