AIRBAG SYSTEM OPERATION CHECK


  1. PRECAUTION FOR OPERATION CHECK

    CAUTION:

    Use the correct procedure to replace the airbag parts.

    B000VVE

  2. CHECK SRS WARNING LIGHT


    1. Primary check


      1. Turn the engine switch on (IG) and check that the SRS warning light turn on.

      2. Turn the engine switch off. Wait for at least 2 seconds, and then turn the engine switch on (IG). The SRS warning light comes on for approximately 6 seconds and diagnosis of the airbag system (including the seat belt pretensioners) is performed.

        Note

        Turn the engine switch off when the battery is connected.

        Tech Tips


        • If the warning light remains on for approximately 6 seconds or more after the engine switch has been turned on (IG), there may be a malfunction with the SRS airbag system.

        • If the warning light occasionally turns on approximately 6 seconds or more after the engine switch has been turned on (IG), there may be a short to +B, short to ground or an open in the SRS warning light circuit.

        • If the warning light illuminates after turning the engine switch off or on (ACC), there may be a malfunction in the power source circuit or combination meter assembly.

        • The SRS warning light turns off, and then turns on. This blinking pattern indicates a source voltage drop. The SRS warning light turns off 10 seconds after the source voltage returns to normal.

  3. FUNCTION OF PASSENGER AIRBAG ON/OFF INDICATOR (w/ Airbag Cutoff Switch)


    1. Initial check


      1. Turn the engine switch on (IG).

      2. The passenger airbag ON/OFF indicator comes on for approximately 4 seconds, and then goes off for approximately 2 seconds.

      3. Approximately 6 seconds after the engine switch is turned on (IG), the passenger airbag ON/OFF indicator will indicate ON/OFF according to the airbag cutoff switch cylinder sub-assembly condition as listed below.

        Indicator Operation
        Airbag Cutoff Switch Cylinder Sub-assembly Condition Passenger Airbag ON/OFF Indicator SRS Warning Light
        ON Indicator OFF Indicator
        On On Off Off
        Off Off On Off
        Switch failure Off On On

        Tech Tips

        If the passenger airbag ON/OFF indicator does not operate as specified in the table according to the airbag cutoff switch cylinder sub-assembly status and the SRS warning light is not illuminated, no DTC will be output. Therefore, perform troubleshooting for Trouble in Passenger Airbag ON/OFF Indicator.

        B000XU7E52

  4. CHECK PASSENGER AIRBAG ON/OFF INDICATOR (w/ Airbag Cutoff Switch)


    1. Turn the engine switch on (IG).

    2. B000UAYC01
      *A Type A
      *B Type B

      Check that the passenger airbag ON/OFF indicator ("ON" and "OFF") comes on for approximately 4 seconds, and then goes off for approximately 2 seconds.

      Tech Tips

      In order to check the operation of the passenger airbag ON/OFF indicator when approximately 6 seconds have elapsed after turning the engine switch on (IG), refer to the table in the previous step.

  5. CHECK HORN BUTTON ASSEMBLY

    Click here

  6. CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

    Click here

  7. CHECK FRONT SEAT AIRBAG ASSEMBLY

    Click here

  8. CHECK CURTAIN SHIELD AIRBAG ASSEMBLY

    Click here

  9. CHECK LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  10. CHECK LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  11. CHECK FRONT SEAT OUTER BELT ASSEMBLY

    Click here

  12. CHECK REAR NO. 1 SEAT OUTER BELT ASSEMBLY

    Click here

  13. CHECK AIRBAG ECU ASSEMBLY

    Click here

  14. CHECK FRONT AIRBAG SENSOR

    Click here

  15. CHECK SIDE AIRBAG SENSOR ASSEMBLY

    Click here

  16. CHECK REAR AIRBAG SENSOR

    Click here

  17. CHECK DOOR SIDE AIRBAG SENSOR

    Click here

  18. CHECK SEAT POSITION AIRBAG SENSOR

    Click here

  19. CHECK HARNESS AND CONNECTOR


    1. for Vehicle not Involved in Collision


      1. Perform a diagnostic system check.

    2. for Vehicle Involved in Collision and Airbag not Deployed


      1. Perform a diagnostic system check.

    3. for Vehicle Involved in Collision and Airbag is Deployed


      1. Perform a diagnostic system check.

      2. Check any of the wire harnesses in exposed contact with the airbag wire harness for damage.

      3. Check the connector of the airbag wire harness for scratches, cracks or damage.