NAVIGATION SYSTEM, Diagnostic DTC:B15D9

DTC Code DTC Name
B15D9 Operation Panel Disconnected

DESCRIPTION

The switch and volume assembly and multi-display are connected by an AVC-LAN communication line. When an AVC-LAN communication error occurs between the radio receiver assembly and switch and volume assembly, these DTCs will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15D9 Operation Panel Disconnected A device that is listed in the AVC-LAN connected device record of the master unit is missing.

  • Switch and volume assembly power source circuit

  • AVC-LAN circuit

  • Switch and volume assembly

  • Multi-display

  • Radio receiver assembly

  • Harness or connector

Tech Tips

For the AVC-LAN communication line, the radio receiver assembly is the master unit.

WIRING DIAGRAM

B000W61E02

CAUTION / NOTICE / HINT

Note


  • Inspect the fuse for circuits related to this system before performing the following procedure.

  • The following malfunctions may occur if a radio receiver assembly from another vehicle is installed to this vehicle. Therefore, when replacing the radio receiver assembly, be sure to replace it with new one.


    • Communication malfunction DTC is output

    • Does not operate normally

Tech Tips

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click here

PROCEDURE


  1. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Check for optional components.


      1. Check that optional components (including associated wiring) which generate radio waves are not installed.

        Result
        Result Proceed to
        Optional components (including associated wiring) are installed. A
        Optional components (including associated wiring) are not installed. B

        Tech Tips


        • Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

        • This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.


    B

    GO TO STEP 4 Click here

    A

  2. REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Remove optional components (including associated wiring).

      Note

      Do not remove optional components or associated wiring without the permission of the customer.

      Result
      Proceed to
      NEXT

    NEXT

  3. CHECK DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    2. Recheck for DTCs and check that no DTCs are output.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (COMMUNICATION MALFUNCTION DUE TO NOISE)

    NG

  4. CHECK HARNESS AND CONNECTOR (SWITCH AND VOLUME ASSEMBLY - BATTERY AND BODY GROUND)


    1. B000WIJC02
      *a

      Front view of wire harness connector

      (to Switch and Volume Assembly)

      Disconnect the switch and volume assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P86-3 (GND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      P86-1 (ACC) - P86-3 (GND) Engine switch on (ACC) 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (SWITCH AND VOLUME ASSEMBLY - MULTI-DISPLAY)


    1. Disconnect the P86 switch and volume assembly connector.

    2. Disconnect the P42 multi-display connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P86-4 (TX+) - P42-6 (TX1+) Always Below 1 Ω
      P86-8 (TX-) - P42-18 (TX1-) Always Below 1 Ω
      P86-4 (TX+) - Body ground Always 10 kΩ or higher
      P86-8 (TX-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK SWITCH AND VOLUME ASSEMBLY


    1. Replace the switch and volume assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (SWITCH AND VOLUME ASSEMBLY IS DEFECTIVE)

    NG

  7. CHECK MULTI-DISPLAY


    1. Replace the multi-display with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (MULTI-DISPLAY IS DEFECTIVE)

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here