NOISE FILTER REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the noise filter removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA/LDA system

Click here

Pre-collision system
Parking assist monitor system

Click here

Steering sensor zero point calibration Variable gear ratio steering system

Click here


  • Front Seat Assembly RH (Only for removal and installation)

  • Front Seat Assembly LH (Only for removal and installation)

 Initialize position control ECU Front Power Seat Control System

Click here

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

B000WAX

Click here

PROCEDURE


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. REMOVE NO. 2 DECK BOARD

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Click here

    CAUTION:

    B000Y52

    • Wait at least 90 seconds after disconnecting the cable from the negative(-) battery terminal to disable the SRS system.

      Click here

    • If the airbag deploys for any reason, it may cause a serious accident.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE FRONT SEAT ASSEMBLY LH

    Click here

  5. REMOVE REAR SEAT CUSHION ASSEMBLY

    Click here

  6. REMOVE REAR SEAT CUSHION LOCK HOOK

    Click here

  7. REMOVE REAR SEAT SIDE GARNISH

    Click here

  8. REMOVE REAR SEATBACK COVER

    Click here

  9. REMOVE REAR SEATBACK ASSEMBLY LH

    Click here

  10. REMOVE RADIO SETTING CONDENSER (for High Mounted Stop Light)

    Note

    When a terminal cover is removed, the radio setting condenser must be replaced because the terminal covers and condenser are supplied as a set.


    1. B000V2C

      Remove the bolt.

    2. Detach the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.

    3. B000Y7DC03
      B000WYJ Remove in this Direction

      Detach the claw and pull out the cover as shown in the illustration.

    4. B000YOZ

      Using a screwdriver, detach the claws and remove the 2 terminal covers with wire harness from the condenser.

    5. B000YNA

      Using a screwdriver, bend back and break off the claw as shown in the illustration.

    6. Remove the terminal cover from the wire harness.

      Note


      • Make sure to hold the crimping side of the terminal when disconnecting the wire harness from the terminal cover.

      • Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.

      • Check for deformation of the terminal after the wire harness has been removed from the terminal cover.

  11. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  12. REMOVE QUARTER INSIDE TRIM BOARD LH

    Click here

  13. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

    Click here

  14. REMOVE OUTER LAP BELT ANCHOR COVER

    Click here

  15. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)

    Click here

  16. REMOVE QUARTER TRIM PANEL ASSEMBLY LH

    Click here

  17. REMOVE RADIO SETTING CONDENSER (for Window Defogger)

    Note

    When the terminal cover is removed, the radio setting condenser must be replaced because the terminal cover and condenser are supplied as a set.


    1. B000XYE

      Remove the bolt.

    2. Detach the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.

    3. B000YGGC02
      B000WYJ Remove in this Direction

      Using a screwdriver, detach the claws and remove the terminal cover with wire harness from the condenser.

    4. B000X9S

      Using a screwdriver, bend back and break off the claw as shown in the illustration.

      Note


      • Make sure to hold the crimping side of the terminal when disconnecting the wire harness from the terminal cover.

      • Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.

      • Check for deformation of the terminal after the wire harness has been removed from the terminal cover.