STEERING COLUMN ASSEMBLY INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. INSTALL STEERING SLIDING WITH SHAFT YOKE SUB-ASSEMBLY


    1. w/o VGRS:


      1. B000XN5C03
        *a Matchmark

        Connect the steering sliding with shaft yoke sub-assembly to the No. 2 steering intermediate shaft assembly.

        Note

        Align the matchmarks on the steering sliding yoke sub-assembly and No. 2 steering intermediate shaft assembly.

      2. Temporarily install the bolt.

    2. w/ VGRS:


      1. B000VZOC04
        *a Matchmark

        Connect the steering sliding with shaft yoke sub-assembly to the steering actuator assembly.

        Note

        Align the matchmarks on the steering sliding with shaft yoke sub-assembly and steering actuator assembly.

      2. Temporarily install the bolt.

  2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  3. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (w/o VGRS)


    1. B000Z01C02
      *a Matchmark

      Install the steering sliding with shaft yoke sub-assembly to the rack and pinion power steering gear assembly.

      Note

      Align the matchmarks on the steering sliding with shaft yoke sub-assembly and rack and pinion power steering gear assembly.

    2. B000VPP

      Install the bolt.

      Torque:
      35.3 N*m  { 360 kgf*cm, 26 ft.*lbf }

    3. Tighten the clamp.

  4. INSTALL STEERING ACTUATOR ASSEMBLY (w/ VGRS)

    Click here

  5. INSTALL STEERING COLUMN ASSEMBLY


    1. w/o VGRS:


      1. B000WEBC01
        *a Matchmark

        Install the steering column assembly to the No. 2 steering intermediate shaft assembly.

        Note

        Align the matchmarks on the steering column assembly and No. 2 steering intermediate shaft assembly.

    2. w/ VGRS:


      1. B000W24C01
        *a Matchmark

        Install the steering column assembly to the steering actuator assembly.

        Note

        Align the matchmarks on the steering column assembly and steering actuator assembly.

    3. Install the steering column assembly with the 2 nuts and bolt.

      Torque:
      36 N*m  { 367 kgf*cm, 27 ft.*lbf }

    4. w/o VGRS:


      1. B000X9N

        Install the bolt.

        Torque:
        35.3 N*m  { 360 kgf*cm, 26 ft.*lbf }

    5. w/ VGRS:


      1. B000V2W

        Install the bolt.

        Torque:
        35.3 N*m  { 360 kgf*cm, 26 ft.*lbf }

    6. Connect each connector and engage each wire harness clamp to the steering column assembly.

    7. B000VLR

      Tighten the bolt.

      Torque:
      35.3 N*m  { 360 kgf*cm, 26 ft.*lbf }

  6. INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

    Click here

  7. INSTALL FRONT WHEEL

    Click here

  8. INSTALL HEATER TO CENTER REGISTER SUB DUCT

    Click here

  9. INSTALL NO. 2 AIR DUCT

    Click here

  10. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  11. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

    Note


    • Do not replace the spiral cable with sensor sub-assembly with the battery connected and the engine switch on (IG).

    • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the engine switch on (IG).

    • Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.


    1. B000WQW

      Using pliers, support the band clamp while loosened and set the turn signal switch assembly with spiral cable sub-assembly.

    2. B000XXMC01
      B000WYJ Install in this Direction

      Engage the claw to install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly as shown in the illustration.

    3. Tighten the band clamp.

    4. Connect each connector to the turn signal switch assembly with spiral cable sub-assembly.

  12. INSTALL UPPER STEERING COLUMN COVER


    1. B000Y4YC01
      B000WYJ Install in this Direction

      Engage the claw to install the upper steering column cover.

    2. B000WT5C03
      B000WYJ Install in this Direction

      Attach the guides and claws in the direction indicated by the arrow in the illustration.

  13. INSTALL LOWER STEERING COLUMN COVER SUB-ASSEMBLY


    1. B000Z6DC01
      B000WYJ Install in this Direction

      Insert the lower steering column cover sub-assembly in the direction indicated by the arrow.

      Note

      Do not damage the tilt and telescopic switch.

    2. Engage the 2 claws.

    3. B000YIHC01
      B000WYJ Install in this Direction

      Engage the claw to install the lower steering column cover sub-assembly to the upper steering column cover.

    4. Install the 3 screws.

  14. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  15. INSPECT AND ADJUST SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

    Click here

  16. INSTALL STEERING WHEEL ASSEMBLY

    Click here

  17. CHECK STEERING WHEEL CENTER POINT

  18. INSTALL HORN BUTTON ASSEMBLY

    Click here

  19. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM


    1. Reset the auto tilt away function setting to the previous condition by changing the customize parameter.

      Click here

  20. PERFORM VARIABLE GEAR RATIO STEERING SYSTEM CALIBRATION (w/ VGRS)

    Click here

  21. ADJUST PARKING ASSIST MONITOR SYSTEM

    Click here